Search PubMed⌕ Search

Biomedical subjects

Georges Guiochon

Publications and source records attributed to Georges Guiochon.

At least 37 records · Page 2Linked to original sources
PubMed2006

Extension of Tóth Psi function from gas-solid to liquid-solid equilibria and application to reversed-phase liquid chromatography systems.

The extension of the Psi function developed by Tóth from equilibria taking place at gas-solid interfaces to those taking place at liquid-solid interfaces was investigated. The results were applied to conventional liquid-solid systems used in reversed-phase liquid chromatography (RPLC). The adsorbents in these systems are made of porous silica having a hydrophobic solid surface obtained by chemically bonding C(18) alkyl chains to a porous silica gel then endcapping the surface with trimethylsilyl groups. The liquid is an aqueous solution of an organic solvent, most often methanol or acetonitrile. The probe compound used here is phenol. Adsorption data of phenol were measured using the dynamic frontal analysis (FA) method. The excess adsorption of the organic solvent was measured using the minor disturbance (MD) method. Activity coefficients in the bulk were estimated through the UNIFAC group contributions. The results show that the Psi function predicts 90% of the total free energy of immersion, DeltaF, of the solid when the concentration of phenol is moderate (typically less than 10 g/L). At higher concentrations, the nonideal behavior of the bulk liquid phase becomes significant and it may contribute up to about 30% of DeltaF. The high concentration of adsorbed molecules of phenol at the interface decreases the interfacial tension, sigma, by about 18 mN/m, independently of the structure of the adsorbed phase and of the nature of the organic solvent.

Journal Article↗
PubMed2006

Adsorption behavior of the (+/-)-Tröger's base enantiomers in the phase system of a silica-based packing coated with amylose tri(3,5-dimethyl carbamate) and 2-propanol and molecular modeling interpretation.

The binary adsorption isotherms of the enantiomers of Tröger's base in the phase system made of Chiral Technologies ChiralPak AD [a silica-based packing coated with amylose tri(3,5-dimethyl carbamate)] as the chiral stationary phase (CSP) and 2-propanol as the mobile phase were measured by the perturbation method. The more retained enantiomer exhibits a S-shaped adsorption isotherm with a clear inflection point, the concentration of the less retained enantiomer having practically no competitive influence on this isotherm: In the entire range of concentrations studied, dq2/dC1 approximately 0. By contrast, the less retained enantiomer has a Langmuir adsorption isotherm when pure. At constant mobile phase concentrations, however, its equilibrium concentration in the adsorbed phase increases with increasing concentration of the more retained enantiomer and dq1/dC2 > 0. This cooperative adsorption behavior, opposed to the classical competitive behavior, is exceedingly rare but was clearly demonstrated in this case. Two adsorption isotherm equations that account for these physical observations were derived. They are based on the formation of an adsorbed multi-layer, as suggested by the isotherm data. The excellent agreement between the experimental overloaded elution profiles of binary mixtures and the profiles calculated with the equilibrium-dispersive model validates this binary isotherm model. The adsorption energies calculated by molecular mechanics (MM) and by molecular dynamics (MD) indicate that the chiral recognition arising from the different interactions between the functional groups of the CSP and the molecules of the Tröger's base enantiomers are mainly driven by their Van der Waals interactions. The MD data suggest that the interactions of the (-)-Tröger's base with the CSP are more favored by 8+/-(5) kJ/mol than those of (+)-Tröger's base. This difference seems to be a contributing factor to the increased retention of the - enantiomer on this chromatographic system. The modeling of the data also indicates that both enantiomers can form high stoichiometry complexes while binding onto the stationary phase, in agreement with the results of the equilibrium isotherm studies.

2-Propanol↗
PubMed2005

A chromatographic estimate of the degree of surface heterogeneity of RPLC packing materials. III. Endcapped amido-embedded reversed phase.

The difference in adsorption behavior between a conventional monomeric endcapped C18 stationary phase (3.43 micromol/m2) and an endcapped polymeric RP-Amide phase (3.31 micromol/m2) was investigated. The adsorption isotherms of four compounds (phenol, caffeine, sodium 2-naphthalene sulfonate, and propranololium chloride) were measured by frontal analysis (FA) and the degree of heterogeneity of each phase for each solute was characterized by their adsorption energy distributions (AED), derived using the Expectation-Maximization method. The results show that only certain analytes (phenol and 2-naphthalene sulfonate) are sensitive to the presence of the polar embedded amide groups within the RP phase. Their binding constants on the amide-bonded phase are significantly higher than on conventional RPLC phases. Furthermore, an additional type of adsorption sites was observed for these two compounds. However, these sites having a low density, their presence does not affect much the retention factors of the two analytes. On the other hand, the adsorption behavior of the other two analytes (caffeine and propranololium chloride) is almost unaffected by the presence of the amide group in the bonded layer. Strong selective interactions may explain these observations. For example, hydrogen-bond interactions between an analyte (e.g., phenol or naphthalene sulfonate) and the carbonyl group (acceptor) or the nitrogen (donor) of the amido-embedded group may take place. No such interactions may take place with either caffeine or the cation propranololium chloride. This study confirms the hypothesis that analytes have ready access to locations deep inside the bonded layer, where the amide groups are present.

Adsorption↗
PubMed2005

A chromatographic estimate of the degree of heterogeneity of RPLC packing materials. 1. Non-endcapped polymeric C30-bonded stationary phase.

A new chromatographic method estimating the degree of heterogeneity of RPLC packing materials is based on the results of systematic measurements of the adsorption data in a wide concentration range for selected probe compounds. These data are acquired by frontal analysis (FA), modeled, and used for the calculation of the adsorption energy distribution (AED). Four compounds were used, two neutral compounds of different molecular sizes (caffeine and phenol) and two ionizable compounds of opposite charges, 2-naphthalene sulfonate, an anion, and propranololium, a cation. This work was done on a C30-bonded silica stationary phase (Prontosil-C30), using the same aqueous mobile phase (30% methanol, v/v) for all compounds, except that sodium chloride (25 mM) was added to elute the ionizable compounds. All four adsorption isotherms have Langmuirian behavior. The AEDs are tri-modal for phenol, quadri-modal for caffeine. The total saturation capacity of the stationary phase is four-fold lower for caffeine than for phenol, due in part to its larger molecular size. The equilibrium constants on the low-energy sites of types 1 and 2 are eight-fold larger. These two types of sites characterize the heterogeneity of the bonded layer itself. The density of the high-energy sites of types 3 and 4 is higher for caffeine, suggesting that caffeine molecules can be accommodated in some hydrophobic cages into which smaller molecules like phenol cannot. These high-energy types of sites characterize the heterogeneity of the whole stationary phase (silica support included). The ionizable compounds have larger molecules than the neutral ones and, accordingly, a lower relative density of sites of type 2 to sites of type 1. A tri-modal and a quadri-modal energy distributions were observed for the 2-naphthalene sulfonate anion and the propranololium cation, respectively. The fourth types of sites measured and its unusually high equilibrium constant are most probably due to ion-exchange interactions between the non-endcapped ionized silanols and the propranololium ion. No such strong interactions are observed with the anionic compound.

Adsorption↗
PubMed2005

A chromatographic estimate of the degree of surface heterogeneity of reversed-phase liquid chromatography packing materials. II-Endcapped monomeric C18-bonded stationary phase.

In a previous report, the heterogeneity of a non-endcapped C30-bonded stationary phase was investigated, based on the results of the measurements of the adsorption isotherms of two neutral compounds (phenol and caffeine) and two ionizable compounds (sodium naphthalene sulfonate and propranololium chloride) by frontal analysis (FA). The same method is applied here for the characterization of the surface heterogeneity of two new brands of endcapped C18-bonded stationary phases (Gemini and Sunfire). The adsorption isotherms of the same four chemicals were measured by FA and the results confirmed by the independent calculation of the adsorption energy distribution (AED), using the expectation-maximization (EM) method. The effect of the length of the bonded alkyl chain was investigated. Shorter alkyl-bonded-chains (C18 versus C30) and the end-capping of the silica surface contribute to decrease the surface heterogeneity under the same experimental conditions (30% methanol, 25 mM NaCl). The AEDs of phenol and caffeine are bimodal with the C18-bonded columns while they are trimodal and quadrimodal, respectively, with a non-endcapped C30-bonded column. The "supersites" (adsorption energy > 20 kJ/mol) found on the C30-Prontosil column and attributed to a cation exchange mechanism completely disappear on the C18-Gemini and C18-Sunfire, probably because the end-capping of the silica surface eliminates most if not all the ionic interactions.

Adsorption↗
PubMed2005

Critical contribution of nonlinear chromatography to the understanding of retention mechanism in reversed-phase liquid chromatography.

The retention of most compounds in RPLC proceeds through a combination of several independent mechanisms. We review a series of recent studies made on the behavior of several commercial C18-bonded stationary phases and of the complex, mixed retention mechanisms that were observed in RPLC. These studies are essentially based on the acquisition of adsorption isotherm data, on the modeling, and on the interpretation of these data. Because linear chromatography deals only with the initial slope of the global, overall, or apparent isotherm, it is unable fully to describe the complete adsorption mechanism. It cannot even afford clues as to the existence of several overlaid retention mechanisms. More specifically, it cannot account for the consequences of the surface heterogeneity of the packing material. The acquisition of equilibrium data in a wide concentration range is required for this purpose. Frontal analysis (FA) of selected probes gives data that can be modeled into equilibrium isotherms of these probes and that can also be used to calculate their adsorption or affinity energy distribution (AED). The combination of these data, the detailed study of the best constants of the isotherm model, the determination of the influence of experimental parameters (e.g., buffer pH and pI, temperature) on the isotherm constants provide important clues regarding the heterogeneity of the adsorbent surface and the main properties of the adsorption mechanisms. The comparison of similar data obtained for the adsorption of neutral and ionizable compounds, treated with the same approach, and the investigation of the influence on the thermodynamics of phase equilibrium of the experimental conditions (temperature, average pressure, mobile phase composition, nature of the organic modifier, and, for ionizable compounds, of the ionic strength, the nature, the concentration of the buffer, and its pH) brings further information. This review provides original conclusions regarding retention mechanisms in RPLC.

Adsorption↗
PubMed2005

Thermodynamic analysis of the heterogenous binding sites of molecularly imprinted polymers.

The thermodynamic interactions of two polymers, one Fmoc-L-Trp-imprinted (MIP), the other one an unimprinted reference (NIP), with the two Fmoc-tryptophan enantiomers were studied by frontal analysis, which allows accurate measurements of the adsorption isotherms. These isotherms were acquired at temperatures of 40, 50, 60, and 70 degrees C, for sample concentrations ranging between 0.005 and 40 mM. The mobile phase used was acetonitrile with one percent acetic acid as an organic modifier. Within the measured concentration ranges, the tri-Langmuir isotherm model accounts best for the isotherm data of both enantiomers on the MIP, the bi-Langmuir model for the isotherm data of Fmoc-L-Trp on the NIP. These isotherm models were selected using three independent processes: statistical tests on the results from regression of the isotherm data to different isotherm models; calculation of the affinity energy distribution from the raw isotherm data; comparison of the experimental and the calculated band profiles. The isotherm parameters obtained from these best selected isotherm models showed that the enantiomeric selectivity does not change significantly with temperature, while the affinity of the substrates for both the MIP and the NIP decrease considerably with increasing temperatures. These temperature effects on the binding performance of the MIP were clarified by considering the thermodynamic functions (i.e., the standard molar Gibbs free energy, the standard molar entropy of adsorption, and the standard molar enthalpy of adsorption) for each identified type of adsorption sites, derived from the Van't Hoff equation. This showed that the entropy of transfer of Fmoc-L-Trp from the mobile to the MIP stationary phase is the dominant driving force for the selective adsorption of Fmoc-L-Trp onto the enantioselective binding sites. This entropy does not change significantly with increasing temperatures from 40 to 70 degrees C.

Adsorption↗
PubMed2005

Comparison of chromatographic band profiles obtained under microwave irradiated and non-irradiated reversed-phase liquid chromatography column.

The possible influence of the application of microwave energy to a reversed-phase liquid chromatography column on the mass transfer kinetics and the thermodynamics of equilibrium between mobile and stationary phases was examined. Chromatograms of propylbenzene and phenol were recorded under the same experimental conditions, on the same column, successively irradiated and not. The effect of microwave irradiation on the mass transfer kinetics was determined by measuring the second moment of small pulses of propylbenzene in a 70:30 (v/v) solution of methanol in water and microwave outputs of 15 and 30 W. The effect of microwave irradiation on the equilibrium thermodynamics was determined by measuring the elution time of breakthrough curves of phenol at high concentrations in a 20:80 (v/v) solution of methanol and water and microwave outputs of 15, 50, and 150 W. A qualitative comparison of the profiles of the propylbenzene peaks obtained with and without irradiation suggests that this irradiation affects significantly the peak shapes. However, a qualitative comparison of the profiles of the breakthrough curves of phenol obtained with and without irradiation suggests that this irradiation has no significant effect on their shapes. The peak sharpening observed may be due to an increase in the diffusivity, resulting from the dielectric polarization under microwave irradiation. This effect is directly related to an increase of the rate of mass transfers in the column. In contrast, the similarity of the overloaded band profiles at high concentrations suggests that the equilibrium thermodynamics is unaffected by microwave irradiation. This may be explained by the transparence of the stationary phase to microwaves at 2.45 GHz. The column temperature was measured at the column outlet under irradiation powers of 15, 30, 50, and 150 W. It increases with increasing power, the corresponding effluent temperatures being 25+/-1, 30+/-1, 35+/-1, and 45+/-1 degrees C, respectively.

Chromatography, Liquid↗
PubMed2005

Adsorption of the enantiomers of 3-chloro-1-phenyl-propanol on silica-bonded chiral quinidine carbamate.

The interactions of 3-chloro-1-phenyl-propanol with a quinidine carbamate-bonded chiral stationary phase under NPLC conditions were studied by measuring the adsorption isotherm data of its enantiomers by frontal analysis, modeling these data with a suitable isotherm model, and comparing the experimental overloaded elution band profiles with those calculated with this isotherm and the equilibrium dispersive model of liquid chromatography. The affinity energy distribution was calculated from the adsorption isotherm data. The results show that the surface of the adsorbent is heterogeneous and exhibits a bimodal adsorption energy distribution. This fact is interpreted in terms of the presence of two different types of adsorption sites on the stationary phase, nonselective and enantioselective sites. Albeit the bi-Langmuir isotherm model successfully accounts for the single-component data corresponding to both enantiomers, the competitive bi-Langmuir isotherm model does not allow an accurate prediction of the overloaded band profiles of the racemic mixture. Thermodynamic data are drawn for explanation. Some aspects of the retention mechanism are discussed in the light of the data obtained.

Adsorption↗
PubMed2005

Chromatographic separation of phenylpropanol enantiomers on a quinidine carbamate-type chiral stationary phase.

The retention and the separation of the enantiomers of 1-phenylpropanol (1PP), 2-phenylpropanol (2PP), and 3-chloro-1-phenylpropanol (3CPP) on silica-bonded quinidine carbamate under normal phase HPLC conditions were investigated. A relatively high selectivity of the stationary phase for 3CPP and 1PP (alpha approximately 1.07-1.09) was achieved with eluents containing ethyl acetate as the polar modifier. These mobile phases were examined in detail. Based on the set of chromatographic and thermodynamic data collected, conclusions regarding the mechanism of enantioselectivity and the structure of the selector chiral center are made.

Acetates↗
PubMed2005

Chromatographic behavior of the enantiomers of 2,2,2-trifluoro-1-(9-anthryl)ethanol on a quinidine-carbamate chiral stationary phase.

The enantioseparation of 2,2,2-trifluoro-1-(9-anthryl)ethanol on silica-bonded quinidine carbamate was examined under linear chromatographic conditions. The significant impact of nonselective adsorption on the retention was demonstrated. The influences of a polar additive in the mobile phase on the retention, the selectivity and the thermodynamic quantities of the retention were measured. A small effect of the pressure on the selectivity and on the accuracy of the thermodynamic measurements was observed.

Acetonitriles↗
PubMed2005

Effects of high pressure in liquid chromatography.

All the experimental parameters that the chromatographers are used to consider as constant (the column length and its diameter, the particle size, the column porosities, the phase ratio, the column hold-up volume, the pressure gradient along the column, the mobile phase density and its viscosity, the diffusion coefficients, the equilibrium constants, the retention factors, the efficiency parameters) depend on pressure to some extent. While this dependence is negligible as long as experiments, measurements, and separations are carried out under conventional pressures not exceeding a few tens of megapascal, it is no longer so when the inlet pressure becomes much larger and exceeds 100 MPa. Equations are developed to determine the extent of the influence of pressure on all these parameters and to account for it. The results obtained are illustrated with graphics. The essential results are that (1) many parameters depend on the inlet pressure, hence on the flow rate; (2) the apparent reproducibility of parameters as simple as the retention factor will be poor if measurements are carried out at different flow rates, unless due corrections are applied to the results; (3) the influence of the temperature on the equilibrium constants should be studied under constant inlet pressure rather than at a constant flow rate, to minimize the coupling effect of pressure and temperature through the temperature dependence of the viscosity; and (4) while reproducibility of results obtained at constant pressure and flow rate will not be affected, method development becomes far more complex because of the pressure dependence of everything.

Chromatography, High Pressure Liquid↗
PubMed2005

Separation mechanism of nortriptyline and amytriptyline in RPLC.

The single and the competitive equilibrium isotherms of nortriptyline and amytriptyline were acquired by frontal analysis (FA) on the C18- bonded discovery column, using a 28/72 (v/v) mixture of acetonitrile and water buffered with phosphate (20 mM, pH 2.70). The adsorption energy distributions (AED) of each compound were calculated from the raw adsorption data. Both the fitting of the adsorption data using multi-linear regression analysis and the AEDs are consistent with a trimodal isotherm model. The single-component isotherm data fit well to the tri-Langmuir isotherm model. The extension to a competitive two-component tri-Langmuir isotherm model based on the best parameters of the single-component isotherms does not account well for the breakthrough curves nor for the overloaded band profiles measured for mixtures of nortriptyline and amytriptyline. However, it was possible to derive adjusted parameters of a competitive tri-Langmuir model based on the fitting of the adsorption data obtained for these mixtures. A very good agreement was then found between the calculated and the experimental overloaded band profiles of all the mixtures injected.

Adsorption↗
PubMed2005

Adsorption on molecularly imprinted polymers of structural analogues of a template. Single-component adsorption isotherm data.

The equilibrium adsorption isotherms on two otherwise identical polymers, one imprinted with Fmoc-L-tryptophan (Fmoc-L-Trp) (MIP), the other nonimprinted (NIP), of compounds that are structural analogues of the template were acquired by frontal analysis (FA) in an acetonitrile/acetic acid (99/1 v/v) mobile phase, over a wide concentration range (from 0.005 to 50 mM). These analogues were Fmoc-L-tyrosine, Fmoc-L-serine, Fmoc-L-phenyalanine, Fmoc-glycine (Fmoc-Gly), Fmoc-L-tryptophan pentafluorophenyl ester (Fmoc-L-Trp(OPfp)), and their antipodes. These substrates have different numbers of functional groups able to interact with the 4-vinylpyridine groups of the polymer. For a given number of the functional groups, these substrates have different hydrophobicities of their side groups (as indicated by their partition coefficients (log P(ow)) in the octanol-water system (e.g., from 4.74 for Fmoc-Trp to 2.53 for Fmoc-Gly)). Statistical results from the fitting of the FA data to Langmuirian isotherm models, the calculation of the affinity energy distribution, and the comparison of calculated and experimental band profiles show that all these sets of FA data are best accounted for by a tri-Langmuir isotherm model, except for the data of Fmoc-L-Trp(OPfp) that are best modeled by a simple Langmuir isotherm. So, all compounds but Fmoc-L-Trp(OPfp) find three different types of adsorption sites on both the MIP and the NIP. The properties of these different types of sites were studied systematically. The results show that the affinity of the structural analogues for the NIP is controlled mostly by the number of the functional groups on the substrates and somewhat by the hydrophobicity of their side groups. These two factors control also the MIP affinity toward the enantiomers of the structural analogues that have a stereochemistry different from that of the template. In contrast, the affinity of the highest affinity sites of the MIP toward the enantiomers of these structural analogues that have the same stereochemistry as the template is highest for the imprinted molecule (Fmoc-L-Trp). The separation of the template from the substrates with the same stereochemistry is influenced by the number of the functional groups on the substrates that can interact with the highest affinity sites on the MIP. The separation of the enantiomers of the analogues of the substrates was also achieved on the MIP, and these enantiomeric separations are influenced by the hydrophobicity of the substrates.

Journal Article↗
PubMed2005

Effect of microwave dielectric heating on intraparticle diffusion in reversed-phase liquid chromatography.

The influence of microwave (MW) irradiation on the mass transfer kinetics in reversed-phase liquid chromatography (RPLC) was studied by placing a column in a microwave oven and measuring the incremental change in the temperature of the column effluent stream at various microwave energies and mobile phase compositions. The microwave energy dissipated in the column was set between 15 and 200 W and the mobile phase composition used varied from 100 to 70, 50, and 10% methanol in water at 1.2 mL/min. At all the mobile phase compositions considered, the effluent temperature increased with increasing microwave energy. At 70% methanol, the mobile phase flow rate was set at 1.2, 2.0, and 2.8 mL/min. At 1.2 mL/min, the effluent temperatures at the lowest (15 W) and highest (200 W) microwave energy inputs were 25 +/- 1 degrees C and 41 +/- 1 degrees C for pure methanol, 25 +/- 1 degrees C and 48 +/- 1 degrees C for 70% methanol, 25 +/- 1 degrees C and 50 +/- 1 degrees C for 50% methanol, and, 25 +/- 1 degrees C and 52 +/- 1 degrees C for 10% methanol, respectively. With 70% methanol and microwave energy inputs of 15, 30, and 50 W, the effluent temperature did not change with increasing flow rate; a considerable change was observed at 100, 150, and 200 W between 1.2 and 2.0 mL/min and none between 2.0 and 2.8 mL/min. Chromatographic elution band profiles of propylbenzene were recorded under linear conditions, in 70% methanol solutions, for microwave energy inputs of 0, 15 and 30 W, at constant temperature. The intraparticle diffusion coefficient, De, under microwave irradiation was ca. 20% higher than without irradiation. These preliminary results suggest that microwave irradiation may have a considerable influence on intraparticle diffusion in RPLC.

Chromatography, Liquid↗
PubMed2005

Calibration of a detector for nonlinear responses.

A calibration curve is often needed to derive from the record of the detector signal the actual concentration profile of the eluate in many studies of the thermodynamic and kinetic of adsorption by chromatography. The calibration task is complicated in the frequent cases in which the detector response is nonlinear. The simplest approach consists in preparing a series of solutions of known concentrations, in flushing them successively through the detector cell, and in recording the height of the plateau response obtained. However, this method requires relatively large amounts of the pure solutes studied. These are not always available, may be most costly, and could be applied to better uses. An alternative procedure consists of deriving this calibration curve from a series of peaks recorded upon the injection of increasingly large pulses of the studied compound. We validated this new method in HPLC with a UV detector. Questions concerning the reproducibility and accuracy of the method are discussed.

Calibration↗
PubMed2005

Extrathermodynamic interpretation of retention equilibria in reversed-phase liquid chromatography using octadecylsilyl-silica gels bonded to C1 and C18 ligands of different densities.

The retention behavior on silica gels bonded to C18 and C1 alkyl ligands of different densities was studied in reversed-phase liquid chromatography (RPLC) from the viewpoints of two extrathermodynamic relationships, enthalpy-entropy compensation (EEC) and linear free energy relationship (LFER). First, the four tests proposed by Krug et al. were applied to the values of the retention equilibrium constants (K) normalized by the alkyl ligand density. These tests showed that a real EEC of the retention equilibrium originates from substantial physico-chemical effects. Second, we derived a new model based on the EEC to explain the LFER between the retention equilibria under different RPLC conditions. The new model indicates how the slope and intercept of the LFER are correlated to the compensation temperatures derived from the EEC analyses and to several parameters characterizing the molecular contributions to the changes in enthalpy and entropy. Finally, we calculated K under various RPLC conditions from only one original experimental K datum by assuming that the contributions of the C18 and C1 ligands to K are additive and that their contributions are proportional to the density of each ligand. The estimated K values are in agreement with the corresponding experimental data, demonstrating that our model is useful to explain the variations of K due to changes in the RPLC conditions.

Chromatography, Liquid↗