Biomedical subjects

Sudeep Taksali

Publications and source records attributed to Sudeep Taksali.

3 recordsLinked to original sources

PubMed2005

Combined fractures of the scaphoid and distal radius: a revised treatment rationale using percutaneous and arthroscopic techniques.

Revision of the treatment rationale for combined fractures of the scaphoid and distal radius is based on evolution of treatment goals. The trend toward early recovery of hand function requires rigid fixation of both fractures before the start ofa hand therapy program. It is clear that prolonged immobilization of the scaphoid fracture jeopardizes early motion protocols for the distal radius. The fixation of unstable distal radius fractures with volar locking plates appears to offer the most stable construct to permit early motion. Evaluation, reduction, and fixation should be accomplished without disruption of the uninjured ligaments required for stable motion or the soft tissue envelope required for healing. Minimally invasive or percutaneous techniques are the meth-ods required. The tools needed are a clear understanding of anatomy, minifluoroscopic imaging units, and small-joint arthroscopy instruments. Many investigators advocate these techniques for scaphoid and distal radius fractures. It is only natural that these techniques should be used for these combined injuries. The key to success is a three-step process: (1)percutaneous reduction of the scaphoid fracture and provisional stabilization with a guide wire placed along its central axis, (2) percutaneous/arthroscopic reduction and rigid fixation of the distal radius fracture to permit early motion, and(3) fixation of the scaphoid fracture. This final step is accomplished by dorsal percutaneous implantation of a cannulated headless compression screw along the central scaphoid axis. Dorsal percutaneous fixation of scaphoid fractures with headless compression screws and rigid fixation of unstable distal radius fractures with a volar lock-ing plate system offer the most secure fixation. This small series suggests that the goals of early recovery of hand function can be accomplished using percutaneous/miniopen techniques for fracture reduction with rigid fixation and minimal risks.

Adolescent↗

PubMed2003

Use of a lateral offset short-leg walking cast before high tibial osteotomy.

The clinical results after high tibial osteotomy for the treatment of symptomatic varus gonarthrosis are unpredictable. Although preoperative gait analysis has been shown to be useful in predicting successful outcome after high tibial osteotomy, there are no readily available preoperative clinical tests for predicting success. The authors did a study to determine the effects of an offset short-leg walking cast as a potential predictor of clinical success after high tibial osteotomy. Specifically, the authors evaluated the effect of an offset short-leg walking cast on pain relief and changes in the peak external adduction moments in patients with symptomatic varus gonarthrosis indicated for high tibial osteotomy. Nineteen consecutive patients indicated for high tibial osteotomy were enrolled and completed the study. All patients had precast gait analysis to determine baseline parameters. Immediately after gait analysis, a short-leg lateral offset walking cast was applied and worn for 3 days to allow time for adaptation. Gait analysis then was repeated. Western Ontario and McMaster Universities Osteoarthritis Index pain scores were obtained before and after the cast was applied. The cast resulted in a mean reduction in pain of 53%, and a mean reduction in the peak external adduction moment of 36% in the 17 of 19 patients who tolerated the cast. The reduction in pain was correlated with the reduction in the peak adduction moment (r = 0.63). The authors conclude that an offset short-leg walking cast results in pain reduction that correlates with changes in external adduction moments about the knee. Therefore, an offset short-leg walking cast may prove to be an effective tool for predicting patients who ultimately will benefit from valgus high tibial osteotomy.

Adult↗

PubMedDate not supplied

Material considerations for intervertebral disc replacement implants.

Cervical and lumbar disc replacements are being performed with increasing frequency. Much of the background for the development for these implants is drawn from the literature of other joint replacements that have been in evolution and use for decades. Important variables for the function and longevity of such disc arthroplasty implants are clearly defined by the material properties of the components used for their production. The most frequently considered materials are cobalt-chrome alloys, titanium alloys, stainless steels, polyethylene, polyurethane and ceramics. In addition to implant materials, the interfaces of such materials must be considered. The bearing surfaces of an implant, in particular, are at risk of wear and failure. Overall, successful, long-term total disc arthroplasty requires a thorough understanding of biomaterials and how they can be used to achieve their desired goals.

Arthroplasty, Replacement↗