Biomedical subjects

David L Kaplan

Publications and source records attributed to David L Kaplan.

65 records · Page 4Linked to original sources

PubMed2001

Cell differentiation by mechanical stress.

Growth factors, hormones, and other regulatory molecules are traditionally required in tissue engineering studies to direct the differentiation of progenitor cells along specific lineages. We demonstrate that mechanical stimulation in vitro, without ligament-selective exogenous growth and differentiation factors, induces the differentiation of mesenchymal progenitor cells from the bone marrow into a ligament cell lineage in preference to alternative paths (i.e., bone or cartilage cell lineages). A bioreactor was designed to permit the controlled application of ligament-like multidimensional mechanical strains (translational and rotational strain) to the undifferentiated cells embedded in a collagen gel. The application of mechanical stress over a period of 21 days up-regulated ligament fibroblast markers, including collagen types I and III and tenascin-C, fostered statistically significant cell alignment and density and resulted in the formation of oriented collagen fibers, all features characteristic of ligament cells. At the same time, no up-regulation of bone or cartilage-specific cell markers was observed.

Animals↗

PubMedDate not supplied

Polymerization of propyl malolactonate in the presence of Candida rugosa lipase.

To gain better insight into mechanistic features of enzyme-catalyzed malolactonate polymerization, reactions with propyl malolactonate were analyzed while varying enzyme concentration, reaction media composition, and reaction temperature. Monomer conversion and product molecular weights were characterized by (1)H NMR and MALDI-TOF MS, respectively. A high extent of thermal polymerization of propyl malolactonate was observed, while the polymer chain length in all reactions was controlled by the elimination of alpha-hydrogen from propyl malolactonate with formation of a new initiator and the new chains. The most efficient enzymatic catalysis occurred in toluene (2.11 M monomer) at 60 degrees C. Candida rugosa lipase (10 wt %) accelerated polymerization 25-fold over the rate of thermal polymerization. The maximum poly(propyl malate) number-average molecular weight obtained was 5000 Da at 20 wt % enzyme with a polydispersity of 1.15. These values compare with 1800 Da and 1.5, respectively, in the absence of enzyme.

Candida↗

PubMedDate not supplied

Electrospinning Bombyx mori silk with poly(ethylene oxide).

Electrospinning for the formation of nanoscale diameter fibers has been explored for high-performance filters and biomaterial scaffolds for vascular grafts or wound dressings. Fibers with nanoscale diameters provide benefits due to high surface area. In the present study we explore electrospinning for protein-based biomaterials to fabricate scaffolds and membranes from regenerated silkworm silk, Bombyx mori, solutions. To improve processability of the protein solution, poly(ethylene oxide) (PEO) with molecular weight of 900,000 was blended with the silk fibroin. A variety of compositions of the silk/PEO aqueous blends were successfully electrospun. The morphology of the fibers was characterized using high-resolution scanning electron microscopy. Fiber diameters were uniform and less than 800 nm. The composition was estimated by X-ray photoelectron spectroscopy to characterize silk/PEO surface content. Aqueous-based electrospining of silk and silk/PEO blends provides potentially useful options for the fabrication of biomaterial scaffolds based on this unique fibrous protein.

Animals↗

PubMedDate not supplied

Enzyme-based molecular imprinting with metals.

Aromatic monomers with various functional groups were utilized in horseradish peroxidase-catalyzed polymerization reactions with metal ions Cu(II), Ni(II), and Fe(III) as imprinting templates. The approach described combines molecular imprinting with enzymatic free radical coupling. Selectivity in metal ion affinity between the various polymer products was assessed and found to depend on the metal used in the imprinting process using aniline, tyramine, and phenol as monomers. Selectivity in binding metals was found when polymers imprinted with copper, nickel, or iron were screened against the three metals, with preference for the metal used in the imprinting step. A model for the structural features of the putative imprinted polymers is proposed based on electron paramagnetic resonance, NMR, and IR analysis. Specific potential benefits to this imprinting method include reactivity with a wide range of aromatic monomers to provide more diverse options for molecular recognition with the target analyte and thus polymer products with higher selectivity, mild reaction conditions for the enzyme polymerization step to enable imprinting against labile substrates, imprinted polymeric products that contain conjugated backbones that could be suitable for electronics-based biosensor applications, and a potential for combinatorial selection to further enhance specificity.

Biotransformation↗

PubMedDate not supplied

Synthesis and characterization of chimeric silkworm silk.

A synthetic gene encoding a chimeric silklike protein was constructed that combined a polyalanine encoding region (Ala)(18), a sequence slightly longer than the (Ala)(12-13) found in the silk fibroin from the wild silkworm Samia cynthia ricini, and a sequence encoding GVGAGYGAGAGYGVGAGYGAGVGYGAGAGY, found in the silk fibroin from the silkworm Bombyx mori. A tetramer of the chimeric repeat sequence encoding a approximately 29 kDa protein was expressed as a fusion protein in Escherichia coli. In comparison to S. c. ricini silk, the chimeric protein demonstrated improved solubility because it could be dissolved in 8 M urea. The purified protein assumed an alpha-helical structure based on solid-state (13)C CP/MAS NMR and was less prone to conformational transition to a beta-sheet, unlike native silk proteins from S. c. ricini. Model peptides representing the crystalline region of S. c. ricini silk fibroin, (Ala)(12) and (Ala)(18), formed beta-sheet structures. Therefore, the solubility and structural transitions of the chimeric protein were significantly altered through the formation of this chimeric silk. This experimental strategy to the study of silk structure and function can be used to develop an improved understanding of the contributions of protein domains in repetitive silkworm and spider silk sequences to structure development and structural transitions.

Amino Acid Sequence↗

PubMedDate not supplied

Porous 3-D scaffolds from regenerated silk fibroin.

Three fabrication techniques, freeze-drying, salt leaching and gas foaming, were used to form porous three-dimensional silk biomaterial matrixes. Matrixes were characterized for morphological and functional properties related to processing method and conditions. The porosity of the salt leached scaffolds varied between 84 and 98% with a compressive strength up to 175 +/- 3 KPa, and the gas foamed scaffolds had porosities of 87-97% and compressive strength up to 280 +/- 4 KPa. The freeze-dried scaffolds were prepared at different freezing temperatures (-80 and -20 degrees C) and subsequently treated with different concentrations (15 and 25%) and hydrophilicity alcohols. The porosity of these scaffolds was up to 99%, and the maximum compressive strength was 30 +/- 2 KPa. Changes in silk fibroin structure during processing to form the 3D matrixes were determined by FT-IR and XrD. The salt leached and gas foaming techniques produced scaffolds with a useful combination of high compressive strength, interconnected pores, and pore sizes greater than 100 microns in diameter. The results suggest that silk-based 3D matrixes can be formed for utility in biomaterial applications.

Animals↗

PubMedDate not supplied

Biomaterial films of Bombyx mori silk fibroin with poly(ethylene oxide).

Phase separation into controllable patterned microstructures was observed for Bombyx mori silkworm silk and poly(ethylene oxide) (PEO) (900000 g/mol) blends cast from solution. The evolution of the microstructures with increasing PEO volume fraction is strikingly similar to the progression of phases and microstructures observed with surfactants. The chemically patterned materials obtained provide engineerable biomaterial surfaces with predictable microscale features which can be used to create topographically patterned or chemically functionalized biomaterials. Solution blending was used to incorporate water-soluble PEO into silk to enhance elasticity and hydrophilicity. The sizes of the globule fibroin phase ranged from 2.1 +/- 0.5 to 18.2 +/- 2.1 microm depending on the ratio of silk/PEO. Optical microscopy and SEM analysis confirmed the micro-phase separation between PEO and silk. Surface properties were determined by XPS and contact angle. Methanol can be used to control the conformational transition of silk fibroin to the insoluble beta-sheet state. Subsequentially, the PEO can be easily extracted from the films with water to generate silk matrixes with definable porosity and enhanced surface roughness. These blend films formed from two biocompatible polymers provide potential new biomaterials for tissue engineering scaffolds.

Animals↗

PubMedDate not supplied

Structure and properties of silk hydrogels.

Control of silk fibroin concentration in aqueous solutions via osmotic stress was studied to assess relationships to gel formation and structural, morphological, and functional (mechanical) changes associated with this process. Environmental factors potentially important in the in vivo processing of aqueous silk fibroin were also studied to determine their contributions to this process. Gelation of silk fibroin aqueous solutions was affected by temperature, Ca(2+), pH, and poly(ethylene oxide) (PEO). Gelation time decreased with increase in protein concentration, decrease in pH, increase in temperature, addition of Ca(2+), and addition of PEO. No change of gelation time was observed with the addition of K(+). Upon gelation, a random coil structure of the silk fibroin was transformed into a beta-sheet structure. Hydrogels with fibroin concentrations >4 wt % exhibited network and spongelike structures on the basis of scanning electron microscopy. Pore sizes of the freeze-dried hydrogels were smaller as the silk fibroin concentration or gelation temperature was increased. Freeze-dried hydrogels formed in the presence of Ca(2+) exhibited larger pores as the concentration of this ion was increased. Mechanical compressive strength and modulus of the hydrogels increased with increase in protein concentration and gelation temperature. The results of these studies provide insight into the sol-gel transitions that silk fibroin undergoes in glands during aqueous processing while also providing important insight in the in vitro processing of these proteins into useful new materials.

Hydrogel, Polyethylene Glycol Dimethacrylate↗

PubMedDate not supplied

Osteogenic differentiation of human bone marrow stromal cells on partially demineralized bone scaffolds in vitro.

Tissue engineering has been used to enhance the utility of biomaterials for clinical bone repair by the incorporation of an osteogenic cell source into a scaffold followed by the in vitro promotion of osteogenic differentiation before host implantation. In this study, three-dimensional, partially demineralized bone scaffolds were investigated for their ability to support osteogenic differentiation of human bone marrow stromal cells (BMSCs) in vitro. Dynamic cell seeding resulted in homogeneous cell attachment and infiltration within the matrix and produced significantly higher seeding efficiencies when compared with a conventional static seeding method. Dynamically seeded scaffolds were cultured for 7 and 14 days in the presence of dexamethasone and evaluated on biochemical, molecular, and morphological levels for osteogenic differentiation. Significant elevation in alkaline phosphatase activity was observed versus controls over the 14-day culture, with a transient peak indicative of early mineralization on day 7. On the basis of RT-PCR, dexamethasone-treated samples showed elevations in alkaline phosphatase and osteocalcin expression levels at 7 and 14 days over nontreated controls, while bone sialoprotein was produced only in the presence of dexamethasone at 14 days. Scanning electron microscopy evaluation of dexamethasone-treated samples at 14 days revealed primarily cuboidal cells indicative of mature osteoblasts, in contrast to nontreated controls displaying a majority of cells with a fibroblastic cell morphology. These results demonstrate that partially demineralized bone can be successfully used with human BMSCs to support osteogenic differentiation in vitro. This osseous biomaterial may offer new potential benefits as a tool for clinical bone replacement.

Adult↗

PubMedDate not supplied

Sequential growth factor application in bone marrow stromal cell ligament engineering.

In vitro bone marrow stromal cell (BMSC) growth may be enhanced through culture medium supplementation, mimicking the biochemical environment in which cells optimally proliferate and differentiate. We hypothesize that the sequential administration of growth factors to first proliferate and then differentiate BMSCs cultured on silk fiber matrices will support the enhanced development of ligament tissue in vitro. Confluent second passage (P2) BMSCs obtained from purified bone marrow aspirates were seeded on RGD-modified silk matrices. Seeded matrices were divided into three groups for 5 days of static culture, with medium supplement of basic fibroblast growth factor (B) (1 ng/mL), epidermal growth factor (E; 1 ng/mL), or growth factor-free control (C). After day 5, medium supplementation was changed to transforming growth factor-beta1 (T; 5 ng/mL) or C for an additional 9 days of culture. Real-time RT-PCR, SEM, MTT, histology, and ELISA for collagen type I of all sample groups were performed. Results indicated that BT supported the greatest cell ingrowth after 14 days of culture in addition to the greatest cumulative collagen type I expression measured by ELISA. Sequential growth factor application promoted significant increases in collagen type I transcript expression from day 5 of culture to day 14, for five of six groups tested. All T-supplemented samples surpassed their respective control samples in both cell ingrowth and collagen deposition. All samples supported spindle-shaped, fibroblast cell morphology, aligning with the direction of silk fibers. These findings indicate significant in vitro ligament development after only 14 days of culture when using a sequential growth factor approach.

Bone Marrow Cells↗

PubMedDate not supplied

Role of adult mesenchymal stem cells in bone tissue engineering applications: current status and future prospects.

Mesenchymal stem cells (MSCs) have been demonstrated as an attractive cell source for tissue-engineering applications because of their ability to be easily isolated and expanded from adult bone marrow aspirates and their versatility for pluripotent differentiation into mesenchymal tissues. This review highlights advances and progress in bone reconstruction techniques for both the repair of site-specific bone defects and the attenuation of musculoskeletal disease symptoms associated with osteoporosis and osteogenesis imperfecta. Despite the enormous potential benefits of MSCs within these approaches, conventional tissue culture methods limit the clinical utility of these cells because of the gradual loss of both their proliferative and differentiation potential during ex vivo expansion. Novel strategies to overcome these limitations are discussed including cultivation in the presence of basic fibroblastic growth factor 2, induction of ectopotic telomerase expression, and ex vivo expansion on various collagenous biomaterials. In addition, this review also outlines mechanistic theories on the potential role of MSC-extracellular matrix interactions in mediating the retention of MSC proliferative and differentiation capacity after ex vivo expansion on collagenous biomaterials.

Animals↗