Search PubMed⌕ Search

SEARCH · Search PubMed

Results for “ACRYLIC RESINS”

Search indexed PubMed citations on genomics, clinical trials, systematic reviews and public health. Explore titles, authors and supplied subject terms, then open the PubMed record.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65Linked to original sources

Effect of thermocycling on bond strength and elasticity of 4 long-term soft denture liners.

STATEMENT OF PROBLEM: Two problems found in prostheses with soft liners are bond failure to the acrylic resin base and loss of elasticity due to material aging. PURPOSE: This in vitro study evaluated the effect of thermocycling on the bond strength and elasticity of 4 long-term soft denture liners to acrylic resin bases. MATERIAL AND METHODS: Four soft lining materials (Molloplast-B, Flexor, Permasoft, and Pro Tech) and 2 acrylic resins (Classico and Lucitone 199) were processed for testing according to manufacturers' instructions. Twenty rectangular specimens (10 x 10-mm(2) cross-sectional area) and twenty cylinder specimens (12.7-mm diameter x 19.0-mm height) for each liner/resin combination were used for the tensile and deformation tests, respectively. Specimen shape and liner thickness were standardized. Samples were divided into a test group that was thermocycled 3000 times and a control group that was stored for 24 hours in water at 37 degrees C. Mean bond strength, expressed in megapascals (MPa), was determined in the tensile test with the use of a universal testing machine at a crosshead speed of 5 mm/min. Elasticity, expressed as percent of permanent deformation, was calculated with an instrument for measuring permanent deformation described in ADA/ANSI specification 18. Data from both tests were examined with 1-way analysis of variance and a Tukey test, with calculation of a Scheffé interval at a 95% confidence level. RESULTS: In the tensile test under control conditions, Molloplast-B (1.51 +/- 0.28 MPa [mean +/- SD]) and Pro Tech (1.44 +/- 0.27 MPa) liners had higher bond strength values than the others (P <.05). With regard to the permanent deformation test, the lowest values were observed for Molloplast-B (0.48% +/- 0.19%) and Flexor (0.44% +/- 0.14%) (P <.05). Under thermocycling conditions, the highest bond strength occurred with Molloplast-B (1.37 +/- 0.24 MPa) (P <.05). With regard to the deformation test, Flexor (0.46% +/- 0.13%) and Molloplast-B (0.44% +/- 0.17%) liners had lower deformation values than the others (P <.05). CONCLUSION: The results of this in vitro study indicated that bond strength and permanent deformity values of the 4 soft denture liners tested varied according to their chemical composition. These tests are not completely valid for application to dental restorations because the forces they encounter are more closely related to shear and tear. However, the above protocol serves as a good method of investigation to evaluate differences between thermocycled and control groups.

Acrylic Resins↗

The effect of tray material and surface condition on the shear bond strength of impression materials.

This study compared the adhesive shear bond strength of three selected impression materials with that of thermoplastic and acrylic resin tray materials as a function of surface preparation. Polyether (Impregum), polyvinylsiloxane (Reprosil), and polysulfide (Permlastic) impression materials were evaluated on smooth, rough, and contaminated tray surfaces. Smooth surface samples were formed against glass and served as the control groups. Experimental groups consisted of samples contaminated with artificial saliva and rough surface samples that were abraded with 110 microns of Al203. A total of 126 samples were subdivided into 18 groups of seven specimens each. Each sample consisted of a 1 inch square, 3 mm thick mass of an impression material sandwiched between the prepared surfaces of a pair of resin plates. Each specimen was tested in a universal testing machine for adhesive shear bond strength. Data were analyzed with three-way analysis of variance and Scheffe's test. The results indicated that the thermoplastic resin material had better adhesive properties than the acrylic resin. For both tray materials mean adhesive shear bond strengths for Impregum and Reprosil were significantly greater than those of Permlastic. Tray surface contaminated with saliva decreased the adhesive shear strength at the tray adhesive impression interface.

Acrylic Resins↗

Wettability of silicone rubber maxillofacial prosthetic materials.

STATEMENT OF PROBLEM: Maxillofacial prosthetic materials that contact skin or mucosa should have good wettability. A material that is easily wetted will form a superior lubricating layer between the supporting tissues and, thus, reduce friction and patient discomfort. The surface energy of a maxillofacial prosthetic material will give an indication of the amount of energy available for adhesion and of the susceptibility of the material to bacterial adhesion. PURPOSE: This study evaluated the wettability and surface energies of a range of commercially available silicone rubber maxillofacial prosthetic materials. MATERIAL AND METHODS: Contact angles and surface energies were measured by using a dynamic contact angle measuring technique. Four commonly used silicone maxillofacial materials were tested and their properties compared with those of an acrylic resin denture base material and a widely used denture soft lining material. RESULTS: There were no significant differences in the wettability of the silicone rubber materials. All materials were significantly less wetted than the denture acrylic resin material. There were no significant differences in the surface energies of the silicone rubber materials, but all were significantly lower than denture acrylic resin material. CONCLUSIONS: The Cahn dynamic contact angle analyzer was a quick and reproducible method for determining the contact angles and surface energies of maxillofacial materials. Further work is needed to improve the wettability of silicone rubber materials used for maxillofacial prostheses, thus, reducing their potential to produce friction with tissues.

Acrylic Resins↗

Comparison of mechanical strength of palatal denture bases made from various plastic materials.

PURPOSE: The aim of the study was to compare the mechanical strength of palatal denture bases made from various plastic materials. MATERIALS AND METHODS: A form and models of an edentulous jaw (Frasaco) were used in the study. The denture bases were made from Zhermacryl H Plus and SR Ivocap Plus (both acrylic resins) and the polyurethane Microbase. Five samples were fabricated for each of the studied polymers. The fracture tests were carried out on a universal testing machine (Hounsfield H5KS). RESULTS: The highest fracture values were assessed on Ivocap specimens. The indicated differences between acrylic resin specimens made of Ivocap and Zhermacryl were not statistically significant. In turn, the differences shown between 2 acrylic resin palatal denture bases and the Microbase were statistically significant (P < .05). CONCLUSION: In this study, samples made from an alternative denture base polymer showed poorer mechanical strength as compared with those made of polymethylmethacrylate.

Acrylic Resins↗

Dimensional stability of occlusal splints.

Five fabrication techniques and two storage methods were used to construct and store specimens to investigate the dimensional stability of acrylic resin occlusal splints. A research model was developed to more closely approximate the tooth coverage limits of occlusal splints. Ten specimens were fabricated on individual stone casts for each of the five techniques. Four die pins were transferred to each specimen, and the distances between the inside diameters of the pins were measured over a 2-week period. After construction, initial measurement, and removal from the cast, each acrylic resin specimen was stored in either a wet or a dry environment. Measurements between pins were made and recorded at five time intervals. The sprinkle-on techniques resulted in less dimensional change than the dough application, the vacuum-adapted resin sheet and dough application, and the heat-cured denture processing techniques. Acrylic resin specimens stored in a wet environment showed less distortion 2 weeks after fabrication.

Acrylic Resins↗

Posterior peripheral seal distortion related to processing temperature.

A conventional acrylic resin was processed at temperatures varying from 135 degrees F to 180 degrees F. No significant distortion in the posterior peripheral seal of a denture base was noted when the material was processed at or below the manufacturer's recommended temperature. Statistically significant distortion was noted in the posterior peripheral seal of a denture base when processing was done above the recommended temperature. An acrylic resin specially designed to be boiled produced significantly less distortion in a denture base than the conventional acrylic resin.

Acrylic Resins↗

Aesthetic dental veneering materials.

They are numerous clinical indications for the use of aesthetic tooth coverings including heavily stained teeth, hypoplasia and other developmental disorders, and traumatic injuries. The acid etch technique provides a means of attaching composite resins and preformed acrylic veneers to enamel to cope with these problems. Four basic techniques are in use: (a) freehand placement of cold-cured or light-cured acrylic resins, (b) use of a crown form with technique (a), (c) commercially performed acrylic laminated bonded to the tooth with cold- or light-cured resins and (d) individually made preformed laminates bonded as in (c). A meticulous acid etch technique is necessary, including the use of 35 per cent phosphoric acid for up to 120 seconds on difficult surfaces such as primary or highly fluorosed enamel. Special care is needed at the gingival margin, for poor bonding is obtained by dentin/cementum. Successful results can be obtained with all four techniques when experience has been gained. The quickest and most flexible technique is (a), whereas (d) is capable of the best contour, adaptation and aesthetics. However, in (d) laboratory procedures add to costs. The most convenient resins for freehand placement and bonding of veneers are the light-cured (composite) resins. Cold-cure resins have short working time and are best used with an unfilled resin primer. Clinical studies indicate that a life of at least 3-4 years for enamel veneers can be expected if incisal coverage is avoided. Research is in progress to improve durability. These restorations should be regarded at present at medium-term treatments and should be so presented to the patient. Even with current materials, a dramatic improvement in appearance can effect a major transformation in the self-esteem of the patient.

Acid Etching, Dental↗

LR Gold embedding of nervous tissue for immunoelectron microscopy studies.

A major drawback of all acrylic resins commonly used for post-embedding immunocytochemical studies of the central nervous system is the disruption of the ultrastructural morphology, due to the high lipid content of neural tissue. We have investigated the suitability of the acrylic resin LR Gold, which has been employed recently for immunogold labeling studies in several non-neural tissues. Optimal preservation of both antigenicity and ultrastructure of nervous tissue was obtained after en bloc staining with uranyl acetate, followed by total dehydration in acetone and curing at low temperature. Cell membranes and myelin sheaths, which are usually lost with other acrylic resins, were well maintained. The degree of antigenicity of LR Gold-embedded tissues was comparable to that of LR White-embedded one, but the morphologic detail was much better preserved. The use of LR Gold is particularly advantageous for studying neurodegenerative disorders such as Alzheimer disease.

Acrylic Resins↗

Processing dentures using a microwave technique.

In this research the technique of curing denture base acrylic resins by microwave energy was investigated with respect to polymerization method, hardness, mechanical and physical properties. Twenty-one different polymerization methods were used by varying radiation power and curing time. The Vickers hardness test was applied to the samples which were polymerized. The average value was found to be 22.46 VHN (Vicker hardness number), that is, almost the same as conventionally cured acrylic. The recommended polymerization method of curing acrylic was 3 min at 550 W in a microwave oven. Mechanical and physical tests were applied to the samples which were cured by the recommended polymerization method. The average transverse load to fracture value was found to be 7.6 kg, and the transverse deflection value was 1.5 mm at 3500 g, and 2.9 mm at 5000 g. Water sorption of acrylic resin cured by microwave energy was 0.72 mg cm-2 and the solubility rate in water was 0.038 mg cm-2. Results conformed with the ADA specification. The findings showed that acrylic resin cured by microwave energy is more resistant to mechanical failure than conventionally cured acrylic and this technique can safely be applied to the production of denture bases.

Acrylic Resins↗

Plastic stopping--update.

Dura Seal powder and liquid and Dura Lay liquid acrylic resin materials have many uses. Methods for using these acrylic resin materials for copings, functionally generated paths, fitting crowns to clasps, centric relation stops, temporary fixed partial dentures, and porcelain additions have been described.

Acrylic Resins↗

The effect of tray selection on the accuracy of elastomeric impression materials.

This study evaluated the accuracy of reproduction of stone casts made from impressions using different tray and impression materials. The tray materials used were an acrylic resin, a thermoplastic, and a plastic. The impression materials used were an additional silicone, a polyether, and a polysulfide. Impressions were made of a stainless steel master die that simulated crown preparations for a fixed partial denture and an acrylic resin model with cross-arch and anteroposterior landmarks in stainless steel that typify clinical intra-arch distances. Impressions of the fixed partial denture simulation were made with all three impression materials and all three tray types. Impressions of the cross-arch and anteroposterior landmarks were made by using all three tray types with only the addition reaction silicone impression material. Impressions were poured at 1 hour with a type IV dental stone. Data were analyzed by using ANOVA with a sample size of five. Results indicated that custom-made trays of acrylic resin and the thermoplastic material performed similarly regarding die accuracy and produced clinically acceptable casts. The stock plastic tray consistently produced casts with greater dimensional change than the two custom trays.

Acrylic Resins↗

The effect of void space and polymerization time on transverse strength of acrylic-glass fibre composite.

The aim of this study was to establish (i) the causes and effects of void space formation in acrylic-glass fibre composite material; and (ii) to clarify the effect of polymerization time of acrylic resin on the transverse strength of heat-cured acrylic resin test specimens. In study 1, three transverse sections of the continuous glass fibre reinforced test specimens (n = 48) were studied by a scanning electron microscope (SEM) and the SEM-micrographs were analysed by a computerized picture analyser. The results suggested that the void space inside the test specimens is caused by a lack of the adsorbed monomer liquid in the fibre bundle before polymerization. The correlation coefficient between these two factors was -0.633 (P < 0.001). No correlation was found between the void space of the acrylic-glass fibre composite and the transverse strength of the test specimens (r = 0.000, P = 1.000). The results of study 2 showed that the transverse strengths of test specimens (n = 240, total) subjected to polymerization of different time spans did not vary significantly (P > 0.05).

Acrylic Resins↗

The effect of complete dentures with a metal palate on candida species growth in HIV-infected patients.

PURPOSE: This in vivo investigation compared the oral candidal population between heat-cured acrylic resin and nickel-chromium-beryllium alloy in maxillary complete dentures in HIV-infected patients. MATERIALS AND METHODS: Split-palate maxillary complete dentures were fabricated for 19 HIV-infected patients: one-half of the palate was made in acrylic resin and the other half in nickel-chromium-beryllium. Patients were divided into low or high CD4+ lymphocyte count groups. Dentures were worn for 5 months. Palatal mucosa was clinically evaluated at baseline, 1, 3, and 5 months after denture insertion. Specimens were collected at 1, 3, and 5 months using a modified imprint culture method. Speciation of Candida was performed using a chromogenic culture medium. Two-sample t-test was employed to determine effects and significant interactions between the control and test groups and the low and high CD4+ lymphocyte groups. A chi(2) test analyzed and compared the results of the clinical evaluation (p < 0.05). RESULTS: Significant differences were observed in the colony counts between both materials during the third (p= 0.046) and fifth months (p= 0.039). The low CD4+ group demonstrated significant differences during the third (p= 0.03) and fifth months (p= 0.05). There were no significant differences between the species of Candida that colonized either material with the exception of Candida dubliniensis (p < 0.001) and "Others" (p < 0.001) during the first and fifth months. There were no significant differences on the clinical appearance of the palatal mucosa between both materials (p= 1.00). CONCLUSIONS: The metal base proved to be effective in decreasing the fungal growth typically present in complete dentures. Although overt clinical manifestations were not present, colony counts of Candida species were high in the acrylic resin denture bases of these patients. This investigation demonstrated that metal base complete dentures provide an important alternative dental service for edentulous HIV-positive and other patients who are particularly prone to higher incidences of fungal infections.

Acrylic Resins↗

Modified functional impression technique for complete dentures.

This report describes the use of a removable acrylic resin tray handle that can be easily attached to custom impression trays to produce an improved peripheral sealing zone. This device can be indicated to develop functional impressions for complete dentures using the patient-conducted muscular motion technique. In upper trays, the handle is fixed in the midline with acrylic resin, while in lower trays the centrally positioned handle is removed before border molding. This removable handle allows patient's suction and free tongue movements. Final impression is carried out in two stages: peripheral sealing (low fusion compound) and recording of the main supporting region of the denture (zinc oxide and eugenol paste). All border records are obtained from the patient's own movements (handle suction and tongue motion). The removable handle is simple to use, is reusable, can be adapted to any individual acrylic resin trays and allows accurate registration of the peripheral sealing zone (border tissues).

Acrylic Resins↗

Release of methyl methacrylate from heat-cured and autopolymerized resins: cytotoxicity testing related to residual monomer.

Three heat-cured and three autopolymerized acrylic denture bases with different mixing proportions and/or processing methods were investigated for the amount of residual monomer content and methyl methacrylate (MMA) released into saliva after incubation during the first and second 24 hours after processing. A corresponding range of concentrations of MMA was also used to test for cell cytotoxicity using a culture of human oral fibroblasts. The results showed that the amount of residual monomer was dependent not only on the type of polymerization but also on the amount of liquid in the mixture ratio and the processing method. The acrylic resin that had the lowest residual monomer also released the smallest amount of MMA but resins which have higher residual monomer may not necessarily release higher amounts of MMA. MMA, tested in the same range of concentration as the MMA found leached from acrylic resin in this study, was found to be toxic in the cell culture. Therefore, it is recommended that dentists attempt to reduce the amount of leachable substances before insertion of new dentures. In addition, it is recommended that dentists advise their patients not to wear newly made dentures overnight, as this may cause mucosal irritation from the potential accumulation of leachable substances.

Acrylic Resins↗

Morphological identification of functional capillaries in the myocardium.

This study used acrylic resin as an intravascular marker to demonstrate functional myocardial capillaries after fixation by perfusion. Eight rat hearts were excised and allowed to function as isolated organs perfused with oxygenated Krebs-Henseleit buffer (37 degrees C, 10 kPa) for 10 min. Four were fixed by perfusion (4 min) with 2.5% glutaraldehyde at the same temperature and pressure and then immersion fixed (24 hr). The other four hearts were perfused with 0.2% procaine HCl for 30 sec just prior to similar fixation. Polymerizing low viscosity acrylic resin was injected at 10 kPa pressure into the fixed vascular beds and allowed to cure, then transmural blocks of left ventricular myocardium were prepared for scanning electron microscopy. Total initial coronary flow of fixative after procaine treatment was significantly increased, while in untreated hearts the initial fixative flow rate was closely similar to that of oxygenated buffer. The pattern of capillary perfusion was assessed, and the percentage of capillary profiles filled by acrylic resin were calculated. Following procaine treatment, 95.2% of capillaries appeared functional, whereas without procaine arrest, only 62.0% of capillaries allowed the passage of resin. This study indicates that perfusion fixation with glutaraldehyde stabilizes myocardial structure so that the proportion of functional capillary pathways remains closely similar to that in the beating heart and so that such functional capillaries can be identified in morphological preparations by using a low viscosity intraluminal resin marker.

Acrylic Resins↗

A provisional and new crown to fit into a clasp of an existing removable partial denture.

A technique that forms an abutment crown to fit into an existing clasp of a removable partial denture by relining an acrylic resin pattern is described. The outer contour of the pattern is made within an irreversible hydrocolloid impression by use of Duralay autopolymerizing acrylic resin applied with precision dispensers. The pattern is formed before tooth preparation and is made approximately 0.4 mm thick. After tooth preparation, the shell pattern is relined with the same autopolymerizing resin and the existing removable partial denture is fitted over it. The gross pattern is trimmed and the margins refined on a die made from an elastomer impression. The refined pattern is cast and finished, avoiding reduction of the contours established. A second crown is similarly formed in tooth-colored autopolymerizing acrylic resin. It serves as a provisional restoration that allows the patient to wear the removable partial denture while the laboratory procedures are performed.

Crowns↗

[On the polymerization of pour type resin (author's transl)].

The initial polymerization point and the polymerization progress have been observed on powder-liquid pour type acrylic resin and one-liquid pour type acrylic resin. The results are as follows: 1. In case of un-heating at the bottom of powder liquid resin, in the former stage the polymerization makes the regular progress from the bottom part to the upper of the mould, but in the latter stage it does some irregular one. In case of heating at the bottom, at first it shows a better regular progress as in the case of un-heating. 2. In case of un-heating at the bottom of one-liquid resin, in the first stage the polymerization makes the regular progress from the bottom part of the resin and at the same time from its middle of the mould, and then to the upper part and the sprue part. In case of heating at the bottom, it begins just from the heated part, then it goes quite regularly to the middle, the upper, and the sprue part, and lastly the polymerization shrinkage concentrates exclusively at the sprue part.

Acrylic Resins↗