Search PubMed⌕ Search

SEARCH · Search PubMed

Results for “Electroplating”

Search indexed PubMed citations on genomics, clinical trials, systematic reviews and public health. Explore titles, authors and supplied subject terms, then open the PubMed record.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27Linked to original sources

Removal of heavy metals in rinsing wastewater from plating factory by adsorption with economical viable materials.

The removal of heavy metals from plating factory wastewater with economical materials was investigated by the column method. Montmorillonite, kaolin, tobermorite, magnetite, silica gel and alumina were used as the economical adsorbents to wastewater containing Cd(II), Cr(VI), Cu(II) and Pb(II). This removal method of heavy metals proved highly effective as removal efficiency tended to increase with increasing pH and decrease with increasing metal concentration. The removal percentages by adsorption onto montmorillonite, tobermorite, magnetite, and silica gel showed high values for all metals. From the results for the heat of adsorption, the adsorption process in the present study might be chemisorption. The proposed method was successfully applied to the removal of Cd(II), Cr(VI) and Cu(II) in rinsing wastewater from plating factory in Nagoya City, Aichi Prefecture, Japan. Since the economical adsorbents used can be obtained commercially because they are easily synthesized, the wastewater treatment system developed is rapid, simple and cheap for the removal of heavy metals.

Adsorption↗

Characterisation of environmentally exposed cement-based stabilised/solidified industrial waste.

A metal-plating waste filter cake treated by stabilisation/solidification (S/S) using ordinary Portland cement (OPC) and pulverised fuel ash (PFA) has been characterised after exposure to the environment in SE England for approximately 10 years. The surface region ( approximately 5cm) was severely degraded, extensively carbonated and had reduced acid neutralisation capacity (ANC) compared to bulk samples. Large 'plate-like' deposits of predominantly calcium hydroxide with a calcium carbonate upper layer were found close to, but below the surface of the exposed S/S waste. Calcium zinc hydroxide (Ca(Zn(OH)(3))(2).2H(2)O) was the major crystalline phase found in the S/S waste in the region below the calcium hydroxide plates (10-15cm). Samples taken from the bulk of the environmentally exposed S/S waste, at a depth of approximately 0.5m, were more amorphous, contained no readily identifiable crystalline phases and had negligible strength but retained high acid neutralisation capacity. Metal analysis of homogenised samples taken from different depths into the S/S waste indicated a reduction in the concentration of heavy metals, such as Zn, Fe and Cr, in the top 5cm of the S/S waste and an increase in concentration of these metals in bulk samples. The majority of crystalline mineral phases detected in the 28-day samples were not identified in the 10-year-old samples.

Construction Materials↗

Genotoxicity of the dust organic extract and its fractions derived from an aluminium electrolytic plant.

The dust derived from an aluminium electrolytic plant was collected on a filter, then extracted by mixed solvent of benzene, hexane and isopropanol (7/2/1, v/v). The solvent-soluble components was separated into five fractions, namely organic acids, organic alkalis, aliphatic hydrocarbons, polycyclic aromatic hydrocarbons and polar compounds. The genotoxicities of the dust organic extract and its five fractions were examined with Ames test, unscheduled DNA synthesis (UDS), micronucleus (MN) and sister-chromatid exchange (SCE) tests in human lymphocytes in vitro which involve the different test systems (bacteria and mammalian cells) and three genetic endpoints (gene mutation, chromosome aberration and DNA damage). The results of four experiments indicated that the dust organic extract showed higher genotoxicity. Among the five fractions, three fractions, namely organic acids, polycyclic aromatic hydrocarbons and polar compounds had higher genotoxicity than others. The other fractions, organic alkalis and aliphatic hydrocarbons had no genotoxicity. According to this study, it is necessary to take effective measures to abate the dust and protect the environment and human health.

Air Pollutants, Occupational↗

Nickel immobilization in ceramic matrix admixed with waste nickel hydroxide.

WAXS examinations performed with nickel hydroxide samples heated to various temperatures showed that freshly settled wet nickel hydroxide sample contains some amount of crystalline beta-Ni(OH)(2) structure and its share increased when sample was dried during 3 weeks at ambient temperature. However, the share significantly decreased when the sample was dried at 110 degrees C and more so at 250 degrees C. Crystalline phase traces of Ni(OH)(2) disappeared after sample burning at 980 degrees C and instead the distinct presence of crystalline NiO was determined. The above samples were examined for solubility in stoichiometric amount of sulphuric acid diluted with water to pH 1.9 and 2.8. Solubility was determined by measuring nickel ion concentration in leachate by the AAS method. The dissolving rate was found to decrease with the rise of temperature to which the nickel hydroxide samples were heated. The solubility of Ni(OH)(2) sample burnt at 980 degrees C was undetectable during 90 h solubility-testing time likely due to its transformation into sparingly soluble crystalline NiO. The latter is considered to be the reason for effective immobilization of waste nickel hydroxide in ceramic prepared by blending with clay and sintering at 980 degrees C.

Aluminum Silicates↗

Processing of copper anodic-slimes for extraction of valuable metals.

This work focuses on processing of anodic slimes obtained from an Egyptian copper electrorefining plant. The anodic slimes are characterized by high concentrations of copper, lead, tin and silver. The proposed hydrometallurgical process consists of two leaching stages for the extraction of copper (H(2)SO(4)-O(2)) and silver (thiourea-Fe3+), and pyrometallurgical treatment of the remaining slimes for production of Pb-Sn soldering alloy. Factors affecting both the leaching and smelting stages were studied.

Conservation of Natural Resources↗

Removal of hexavalent chromium using distillery sludge.

Batch mode experiments were conducted to study the removal of hexavalent chromium from aqueous and industrial effluent using distillery sludge. Effects of pH, contact time, initial concentration and adsorbent dosage on the adsorption of Cr(VI) were studied. The data obeyed Langmuir and Freundlich adsorption isotherms. The Langmuir adsorption capacity was found to be 5.7 mg/g. Freundlich constants K(f) and n were 2.05 [mg/g(L/mg)(n)] and 3.9, respectively. Desorption studies indicated the removal of 82% of the hexavalent chromium. The efficiency of adsorbent towards the removal of chromium was also tested using chromium-plating wastewater.

Adsorption↗

Comparison of methods for preparation of 125I brachytherapy source cores for the treatment of eye cancer.

Two procedures for fixing the 125I activity on different matrices were explored. In the first method, anodic deposition of 125I on silver wire was used. In the second, 125I was adsorbed as iodate (IO3-) on alumina microspheres by using a solid-solution interface technique. While the 125I uptake was approximately 84% on the silver wires by electrodeposition method, the microspheres showed approximately 97% by the solid-solution interface technique. The low leachable (0.05%) wires, and comparatively high leachable (approximately 4%) spheres were trial encapsulated and laser welded. The encapsulated sources were measured for source strength and were found to be suitable for the treatment of eye cancer.

Adsorption↗

A rapid method for alpha-spectrometric analysis of radium isotopes in natural waters using ion-selective membrane technology.

An alpha-spectrometric method for the rapid determination of radium isotopes (223Ra, 224Ra and 226Ra) in environmental samples is presented. Using Empore Radium Rad Disks complete separation of the target radionuclides is achieved. The high selectivity of these Rad Disks allows the straightforward use of 225Ra as yield tracer. Chemical yield is up to 92 +/- 9%. The chemical procedure can be accomplished within 5h. Alpha-sources show energy resolution in the range of typically 26-40 keV (FWHM). Despite minimal thickness of the sources no significant radon (Rn) losses can be observed.

Alpha Particles↗

Controlling the electrochemically active area of carbon fiber microelectrodes by the electrodeposition and selective removal of an insulating photoresist.

A new and simple method permits control of the electrochemically active area of a carbon fiber microelectrode. An electrophoretic photoresist insulates the 10-microm-diameter carbon fiber microelectrodes. Photolysis of the photoresist followed by immersion of the exposed area into a developing solution reveals electroactive carbon fiber surface. The electroactive surface area exposed can be controlled with a good degree of reproducibility.

Carbon↗

Investigation into the rejuvenation of spent electroless nickel baths by electrodialysis.

Electroless nickel plating generates substantially more waste than other metal-finishing processes due to the inherent limited bath life and the need for regular bath disposal. Electrodialysis can be used to regenerate electroless nickel baths, but poor membrane permselectivity, leading to high losses of valuable bath components, continues to be a weakness of the technology. This research has investigated improving electrodialysis permselectivity for removing contaminants (sodium, orthophosphite, and sulfate) in a spent electroless nickel bath while minimizing the losses of valuable bath ions (nickel, hypophosphite, and organic acids). Ion permselectivity was explored with respect to electrodialysis operating conditions, membrane type, and cell configuration. Excellent permselectivity for sodium over nickel was attained irrespective of operating condition, membrane, or cell configuration. Studies on the effects of four different operating conditions (current density, pH, flow rate, and temperature) on anion permselectivity revealed bath pH and current density to be critical operating parameters. The type of anion exchange membrane used had a crucial effect on selectivity; one membrane (Ionac MA-3475) was identified as having superior selectivity for bath contaminants particularly for sulfate. The improvements in electrodialysis permselectivity established by this research will decrease waste generation within the electroless nickel process and increase resource productivity by minimizing the loss of valuable plating chemicals.

Electroplating↗

Comparing Nafion and ceramic separators used in electrochemical purification of spent chromium plating solutions: cationic impurity removal and transport.

This study focuses on the electrolytic regeneration of spent chromium plating solutions. These solutions contain a significant amount of chromium and a lesser amount of other heavy metals, which makes them a significant environmental concern and an obvious target for recycling and reuse. The type of separator used is extremely critical to the performance of the process because they are the major resistance in the transport-related impurity (Cu(II), Ni(II), and Fe(III)) removals from contaminated chromic acid solutions. A Nafion 117 membrane and a ceramic diaphragm separator traditionally used in the industry were tested for comparison. It was found that the mobilities of Cu(II) and Ni(II) were similar and higher than that of Fe(III) using both separators. The mobility of each cation was smaller in the Nafion membrane than in the ceramic diaphragm. The measured conductivity of the ceramic diaphragm was slightly higher than that of Nafion membrane. However, the Nafion membrane was much thinner than the ceramic diaphragm resulting in the system using the Nafion membrane having higher impurity removal rates than the system using the ceramic diaphragm. The removal rates were approximately equal for Cu(II) and Ni(II) and lowest for Fe(III). Both current and initial concentration affected the removal rates of the impurities. Modeling results indicated that a system using a Nafion separator and a small catholyte/anolyte volume ratio was better than a system using a ceramic separator for removing impurities from concentrated plating solutions if the impurities transported into the catholyte are deposited or precipitated.

Ceramics↗

Adsorbed U(VI) surface species on muscovite identified by laser fluorescence spectroscopy and transmission electron microscopy.

Time-resolved laser-induced fluorescence spectroscopy (TRLFS) and high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) were applied to investigate the species of uranyl(VI) adsorbed onto muscovite platelets and muscovite suspensions (grain size: 63-200 microm). TRLFS provided evidence for the presence of two adsorbed uranium(VI) surface species on edge-surfaces of muscovite. The two species showed different positions of the fluorescence emission bands and different fluorescence lifetimes indicating a different coordination environment for the two species. HAADF-STEM revealed that nanoclusters of an amorphous uranium phase were attached to the edge-surfaces of muscovite powder during batch sorption experiments. These U-nanoclusters were not observed on {00/} cleavage planes of the muscovite. The surface species with the shorter fluorescence lifetimes are interpreted as truly adsorbed bidentate surface complexes, in which the U(VI) binds to aluminol groups of edge-surfaces. The surface species with the longer fluorescence lifetimes are interpreted to be an amorphous U(VI) condensate or nanosized clusters of polynuclear uranyl(VI) surface species with a particle diameter of 1 to 2 nm. Depending on the size of these clusters the fluorescence lifetimes vary; i.e., the larger the nanosized clusters, the longer is the fluorescence lifetime.

Adsorption↗

Self-assembly of 10-microm-sized objects into ordered three-dimensional arrays.

This paper describes the self-assembly of small objects--polyhedral metal plates with largest dimensions of 10 to 30 microm--into highly ordered, three-dimensional arrays. The plates were fabricated using photolithography and electrodeposition techniques, and the faces of the plates were functionalized to be hydrophobic or hydrophilic using self-assembled monolayers (SAMs). Self-assembly occurs in water through capillary interactions between thin films of a hydrophobic liquid (a liquid prepolymer adhesive) coated onto the hydrophobic faces of the plates; coalescence of the adhesive films reduces the interfacial free energy of the system and drives self-assembly. By altering the size and surface-patterning of the plates, the external morphologies of the aggregates were varied. Curing the adhesive furnished mechanically stable aggregates that were characterized by scanning electron microscopy (SEM). For assemblies formed by plates partially composed of a sacrificial material, a subsequent etching step furnished fully open, three-dimensional microstructures. This work validates the use of capillary interactions for three-dimensional mesoscale self-assembly in the 10-microm-size regime and opens new avenues for the fabrication of complex, three-dimensional microscructures.

Electroplating↗

Polyamidoamine dendrimers-assisted electrodeposition of gold-platinum bimetallic nanoflowers.

Novel Au-Pt bimetallic flower nanostructures fabricated on a polyamidoamine dendrimers-modified surface by electrodeposition are reported. These polyamidoamine dendrimers were stable, and they assisted the formation of Au-Pt bimetallic nanoflowers during the electrodeposition process. These nanoflowers were characterized by field-emitted scanning electron microscopy (FE-SEM), energy-dispersive spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction, and electrochemical methods. FE-SEM images showed that the bimetallic nanoflower included two parts: the "light" and the "pale" part. The two parts consisted of many small bimetallic nanoparticles, which was attributed to the progressive nucleation process. Moreover, the "light" part contained more bimetallic nanoparticles. The morphologies of bimetallic nanoflowers depended on the electrodeposition time and potential and the layer number of assembled dendrimers. The average size of nanoflowers increased with the increase in electrodeposition time. The layer number of assembled dendrimers obviously affected the size and morphologies of the "pale" parts of deposited nanoflowers. EDS and XPS indicated that the content of Au element was higher than that of Pt element in the nanoflowers. The bimetallic nanoflowers-modified electrode had electrochemical properties similar to those of bare gold and platinum electrodes. It also exhibited significant electrocatalytic activities toward oxygen reduction.

Amides↗

Chitosan-mediated and spatially selective electrodeposition of nanoscale particles.

Nanoscale particles offer a variety of interesting properties, and there is growing interest in their assembly into higher ordered structures. We report that the pH-responsive aminopolysaccharide chitosan can mediate the electrodeposition of model nanoparticles. Chitosan is known to electrodeposit at the cathode surface in response to a high localized pH. To demonstrate that chitosan can mediate nanoparticle deposition, we suspended fluorescently labeled latex nanoparticles (100 nm diameter spheres) in a chitosan solution (1%) and performed electrodeposition (0.05 mA/cm2 for several minutes). Results demonstrate that chitosan is required for nanoparticle electrodeposition; chitosan confers spatial selectivity to electrodeposition; and nanoparticles distribute throughout the electrodeposited chitosan film. Additionally, we observed that the deposited films reversibly swell upon rehydration. This work indicates that chitosan provides a simple means to assemble nanoparticles at addressable locations and provides further evidence that stimuli-responsive biological materials may facilitate fabrication at the microscale.

Biocompatible Materials↗

Epitaxial electrodeposition of ZnO on Au(111) from alkaline solution: exploiting amphoterism in Zn(II).

The amphoteric nature of ZnO is used to produce the material from strongly alkaline solution. The solution pH is lowered globally to produce ZnO powder, and it is lowered locally at a Au(111) surface to produce epitaxial films. ZnO powder is precipitated from a solution of 10 mM Zn(II) in 0.25 M NaOH by simply adding 1 M HNO3 to the solution. For the film electrodeposition, the local pH at the electrode surface is decreased by electrochemically oxidizing the ascorbate dianion. The chemically precipitated ZnO powder grows with a sea urchin-like nanostructure, whereas the electrodeposited films have a columnar structure. ZnO electrodeposited onto a Au(111) single crystal has a ZnO(0001)[1011]//Au(111)[110] orientation relationship.

Alkalies↗

Mechanistic study of the electrodeposition of nanoporous self-assembled ZnO/Eosin Y hybrid thin films: effect of eosin concentration.

ZnO films prepared by one-step electrodeposition in the presence of dissolved eosin molecules present an internal nanoporous hybrid structure resulting from self-assembling processes occurring in solution between ZnO and eosin components. This study aims to better understand the underlying growth mechanism, which is still unexplained. The films were deposited by cathodic electrodeposition from an oxygen-saturated aqueous zinc chloride solution. The effects of the addition of 10 to 100 micromol.L(-1) eosin Y, as a sodium salt, on the growth rate and film properties, were systematically studied while all other parameters remained constant (concentrations of zinc salt and supporting electrolyte, applied potential of -1.4 V versus the mercurous sulfate electrode (MSE), temperature of 70 degrees C, rotating disk electrode at 300 rotations per min, and a glass-coated tin oxide electrode). It is shown that the addition of eosin provokes the formation of a nanoporous "cauliflower" structure whose nodule size and composition depend on the eosin concentration in the bath. The growth rate of the hybrid films increases markedly with the eosin concentration. The ZnO and eosin contents of the films are determined for each concentration by chemical analysis. Comparing with thickness determinations, it is shown that the total porosity increases up to 60-65% in volume fraction toward an eosin concentration of 100 micromol.L(-1). The empty pore volume fraction increases up to about 30% at an eosin concentration of about 20 micromol.L(-1) and then decreases. These correlations have been precisely established for the first time. It is shown that the global composition is fixed by the relative rate of deposition for zinc oxide, which is constant, and for the relative rate of eosin inclusion, which is proportional to the concentration in solution. This is explained on the basis of different steps in the growth mechanism, in particular, a diffusion effect limitation for both oxygen and eosin. This variation explains part of the increase in the growth rate. Another contribution is related by the structural effect on the nanoscale leading to the formation of the interpenetrated porous network. Competition between empty and eosin-filled parts of the pore network is evidenced. The formation of the porous network structure could be governed by a diffusion-limited aggregation mechanism. The system may represent a reference case of competing reactions in the electrochemical self-assembly of hybrid nanostructures.

Electrochemistry↗

Bismuth telluride (Bi2Te3) nanowires: synthesis by cyclic electrodeposition/stripping, thinning by electrooxidation, and electrical power generation.

Nanowires composed of the thermoelectric material Bi2Te3 were synthesized on highly oriented pyrolytic graphite (HOPG) electrodes using the electrochemical step edge decoration (ESED) method. Nanowire synthesis was initiated by applying a voltage pulse of -0.75 V versus SCE for 5 ms to an HOPG electrode in an aqueous solution containing both Bi3+ and TeO22-, thereby producing nuclei at the step edges. Bi2Te3 was electrodeposited onto these nuclei using a cyclic electrodeposition-stripping scheme that involved the electrodeposition of bismuth-rich Bi2Te3 on a negative-going voltammetric scan (to -0.05 V) and the subsequent anodic stripping of excess bismuth from these nanowires during a positive-going scan (to +0.35 V). When this cycle was repeated 10-50 times, Bi2Te3 nanowires in the 100-300-nm-diameter range were obtained. These nanowires were narrowly dispersed in diameter (RSDdia = 10-20%), were more than 100 microm in length, and were organized into parallel arrays containing hundreds of wires. Smaller nanowires, with diameters down to 30 nm, were obtained by electrooxidizing 150-nm-diameter Bi2Te3 nanowires at +0.37 V under conditions of kinetic control. This oxidation process unexpectedly improved the uniformity of Bi2Te3 nanowires, and X-ray photoelectron spectroscopy (XPS) shows that these nanowires retain a Bi2Te3 core but also have a thin surface layer composed of Bi and Te oxides. The ability of Bi2Te3 nanowires to generate electrical power was assessed by transferring ensembles of these nanowires onto cyanoacrylate-coated glass surfaces and evaporating 4-point nickel contacts. A dimensionless figure of merit, ZT, ranging from 0 to 0.85 was measured for fresh samples that were less than 1 day old. XPS reveals that Bi2Te3 nanowires are oxidized within a week to Bi2O3 and TeO2. These oxides may interfere with the application by evaporation of electrical contacts to these nanowires.

Alloys↗