PubMed · 4449028
The source did not provide an abstract. Follow the original record for more information.
Explore connections, maps & timelines
W F Stanaszek, R S Levinson, B Ecanow. 1974. Halothane uptake by coacervate systems.. https://doi.org/10.1002/jps.2600631225
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
The interactions of the silane coupling agent methacryloxypropyltrimethoxysilane (MPS) with both fumed silica and a polymethylmethacrylate (PMMA) resin matrix were investigated using thermogravimetric analysis and Fourier transform infrared spectroscopy. OX 50 fumed silica was silanated with MPS at concentrations of 1% and 5% in aqueous ethanol (95%), acetone, and anhydrous toluene. Methyl methacrylate was polymerized with the silanated fumed silica (5% wt/wt) to form composites. The amount of MPS adsorption on the fumed silica and the amount of PMMA attached to the silanated fumed silica were determined by thermogravimetric analysis. MPS could be removed from the fumed silica after washing with methanol, but not after it underwent a drying process at 25 degrees C under vacuum. After vacuum drying at 25 degrees C, two types of adsorbed silane were found, i.e., firmly adsorbed and loosely adsorbed silane. The loosely adsorbed silane could desorb from silica and be incorporated into the polymer matrix through copolymerization with monomeric methyl methacrylate, resulting in crosslinking of the matrix. When the silanated silica was dried at 110 degrees C for 2 h, the loosely adsorbed silane was removed and the amount of firmly adsorbed silane increased. There was a positive correlation between the amount of firmly adsorbed MPS and the amount of PMMA attachment. The highest efficiency for PMMA attachment was found when MPS was adsorbed as a monolayer, because the loosely adsorbed silane did not contribute to the bonding of PMMA, and this suggested that not all of the double bonds of the MPS were accessible for reaction with the methacrylate monomer. Drying at 110 degrees C may also decrease the number of unsaturated double bonds of MPS.
Mucoadhesive, hydroxypropylcellulose (HPC) microspheres were prepared for powder inhalation and their feasibility for enhancing pulmonary drug absorption was investigated. Respirable-sized microspheres, incorporating crystalline or amorphous fluorescein (used as a model drug), were prepared by spray-drying aqueous or ethanol HPC systems, respectively. These were prepared from a variety of HPC grades (SL, L, M and H types) in different fluorescein-HPC ratios (1:1-1:10). The microspheres were administered to tracheally-intubated guinea pigs as powder aerosols and their fluorescein pharmacokinetics studied, and compared to those for pure crystalline fluorescein ('control'). All microspheres were prepared and aerosolized within a MMAD range of 1.3-2.6 microm (GSD< or =2.1). Fluorescein's dissolution was increased in the amorphous form by 6.5-fold when compared to the crystalline material (83.9-87.2 vs. 13.5 microg/ml, respectively). Poor dissolution for the 'control' crystalline fluorescein appeared to be rate-determined, which showed bi-phasic absorption profiles (T(max)=60 min), simultaneously competing with mucociliary clearance out of the lower airways. While the crystalline/HPC microspheres prolonged absorption, the amorphous fluorescein/HPC microspheres showed rapid absorption with T(max)=0 min (immediately after the administration had terminated). This was explained by enhanced fluorescein dissolution and was consistently observed irrespective of the fluorescein-HPC ratio or HPC grade. However, the microspheres with the least viscous HPC-SL and the lowest fluorescein-HPC ratio (1:1) failed to enhance bioavailability, presumably because the mucociliary clearance was undisturbed. In contrast, the microspheres with the highly viscous HPC-H with ratios > or = 1:4 successfully enhanced absorption, achieving 88.0% bioavailability by virtue of HPC increasing the dissolution and retarding the mucociliary clearance.
The purpose of this study was to investigate the possibility to develop different levels of correlation between in vitro dissolution parameters and in vivo pharmacokinetic parameters for three rifampicin formulations. A level A correlation of in vitro release and in vivo absorption could be obtained for individual plasma level data by means of the Wagner and Nelson method. Linear correlation could be obtained when percent dose released in vitro was plotted vs percent dose absorbed in vivo with correlation coefficients between 0.954,0.983 and 0.997 for the formulations studied. A second level correlation between mean in vitro dissolution time (MDT) and mean in vivo residence time (MRT) was performed with a correlation coefficient of 0.536,0.420 and 0.335. Finally, it was also possible to establish a good in vitro-in vivo correlation when the T(50%hrs) (time taken to release 50% of rifampicin) in vitro and C(max),T(max) or AUC in vivo were compared.