PubMed · 15726796
The source did not provide an abstract. Follow the original record for more information.
Explore connections, maps & timelines
2004. Dentin bonding.. https://pubmed.ncbi.nlm.nih.gov/15726796/
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
The structural integrity of fibrillar type I collagen is critical for effective dentin bonding. Since most noncollagenous matrix components in dentin are closely associated with collagen, we hypothesized that they may also contribute to dentin bonding. To test this hypothesis, bovine dentin was acid-etched, treated with chondroitinase ABC (C-ABC), endo-beta-galactosidase (Endo-beta), or trypsin. Controls were prepared in the same manner but without the enzymes. All control and experimental specimens were then bonded with One-Step. Bond strength data were analyzed by one-way ANOVA and Fisher's PLSD test (p < 0.05). When dentin was treated with C-ABC or trypsin, bond strengths significantly decreased for the rewetted groups (p < 0.05). The treatment with Endo-beta showed no effects on bond strengths (p > 0.05). When the treated dentin surfaces were observed under SEM, the C-ABC and trypsin treated groups revealed significant loss of collagen fibril architecture. The results indicate that chondroitin sulfate glycosaminoglycans and trypsin-digestible noncollagenous proteins play roles in maintaining the open dimensions of the collagen fibril scaffold, which is essential for optimal dentin bonding.
Although 4-META/MMA-TBB resin has adhesive properties to dentin, and has been clinically used for the bonding treatment of vertically fractured roots and apicoectomy, there has not been any investigation on the adhesion of 4-META/MMA-TBB resin to cementum. The purpose of this in vitro study was to evaluate the bonding and the sealing ability of 4-META/MMA-TBB resin to cementum. Bovine root cementum and dentin surfaces were treated with a citric acid and ferric chloride solution, and the 4-META/MMA-TBB resin was applied on the treated surfaces before testing. The microtensile bond strength and the leakage levels obtained for the cementum were almost equal to those for the dentin. In SEM and TEM observations, a hybrid layer approximately 2-3 microm in thickness was observed at the interface between the resin and the cementum. It is concluded that 4-META/MMA-TBB resin adhered to cementum via a hybrid layer on cementum, as previously reported for dentin.
OBJECTIVES: Dentin bonds made with one-bottle etch-and-rinse and self-etch adhesives are affected by the formation of interfacial blisters, porosities and deterioration. The first objective of this study was to evaluate the fluid flow through resin-dentin interfaces created by self-etching adhesives applied to deep dentin using a replica technique and by directly measuring dentin permeability (P). The second objective was to examine the effect of intrapulpal pressure on the microtensile bond strength of these adhesives. METHODS: A fluid-transport model was used to measure the fluid permeability (%P) through different adhesives. Impressions of bonded dentin were taken with a polyvinylsiloxane impression material to monitor fluid transudation from the surface of the adhesive. Positive replicas were fabricated for SEM examination. Two groups of resin-bonded specimens (pulpal pressure versus no pulpal pressure) were created for microtensile bond strength evaluation. Adhesive application was performed under 0 cm H(2)O. Pulpal pressure group was submitted to 20 cm H(2)O of pulpal pressure during build-up procedures. RESULTS: Clearfil Protect Bond exhibited the lowest permeability and fewest numbers of fluid droplets over the surface of the bonded dentin. G-Bond and Clearfil-S3 Bond were more permeable than Clearfil Protect Bond. One Up Bond F was the most permeable adhesive. A highly significant correlation was observed between the relative permeability of these adhesives (%P) and the number of fluid droplets on the adhesive surfaces. The application of pulpal pressure significantly reduced bond strength. SIGNIFICANCE: Resin-dentin bonds created by contemporary self-etch adhesives are susceptible to fluid permeation induced by pulpal pressure. HEMA-based adhesives showed the largest reductions in bond strengths after pulpal pressure application.