PubMed · 14952320
The source did not provide an abstract. Follow the original record for more information.
Explore connections, maps & timelines
R K W KUIPERS. [Auric nephrosis].. https://pubmed.ncbi.nlm.nih.gov/14952320/
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
Sustainable nanomaterial synthesis has emerged as a critical strategy to reduce the environmental burden associated with conventional chemical synthesis method. Microalgae-derived biomolecules offer a promising platform for the green production of metal nanoparticles due to their rich bioactive compounds capable of acting as natural reducing and stabilizing agents. Here, we report the eco-friendly synthesis of gold nanoparticles (AuNPs) using extract of Indonesian microalga Chlorella vulgaris extract. To optimize the synthesis process, the effects of precursor-to-extract ratio, temperature, and incubation time were evaluated. Optimal synthesis of C5-AuNPs was obtained at 37 °C for 20 h with precursor to extract ratio of 6:4, resulting in moderately stable C5-AuNPs characterized by a surface plasmon resonance (SPR) peak at 541 nm. Furthermore, Fourier-transmission infra-red (FT-IR) analysis revealed the involvement of functional groups of C. vulgaris extract in the interaction with Au+ during the production of C5-AuNPs. Transmission electron microscopy (TEM) demonstrated the formation of uniformly spherical nanoparticles with an average diameter of approximately 8.8 nm. Biological evaluation showed that the synthesized C5-AuNPs exerted pronounced dose-dependent cytotoxicity against MCF-7 breast cancer cells with an IC50 threshold of 21.17 ppm, while no toxicity appears in normal HEK293 cells. Mechanistically, the C5-AuNPs induced early apoptosis and inhibit cell-cycle progression at the stage of G0/G1. Collectively, these findings demonstrate that C. vulgaris-mediated AuNPs represent a promising preliminary in vitro findings for cancer therapy candidate.
This paper reports on the structural characteristics of microcontact printed oligo(ethylene glycol)-terminated alkanethiol layers, HS(CH2)15CONH-(CH2CH2O)6-H (hereafter EG6), on gold. Microwetting, contact angle goniometry, imaging null ellipsometry, and infrared reflection-absorption spectroscopy (IRAS) are used to characterize the printed EG6 layers, and the quality of these layers in terms of layer thickness and the crystallinity of the alkyl and ethylene glycol portions is compared with data obtained from analogous layers prepared by solution self-assembly. The outcome of the printing process is critically dependent on the experimental parameters used to prepare the patterns. It is found that high quality layers, consisting of densely packed all-trans alkyl chains terminated with relatively helical hexa(ethylene glycol) tails, are formed by inking the poly(dimethylsiloxane) (PDMS) stamp with a 1 mM EG6 solution and contacting it with gold for 15 min. The homogeneity of printed layers is not as good as the homogeneity of those prepared from solution under similar conditions, most likely because of simultaneous transfer of low molecular weight residues from the PDMS stamp. These residues, however, can be easily removed upon ultrasonication in ethanol without affecting the quality of the printed layer. Further on, the microscopic square-shaped bare gold patterns formed after microcontact printing (muCP) are subsequently filled with 16-hexadecanoic acid (hereafter THA) or HS(CH2)15CONH-(CH2CH2O)6-COOH (hereafter EG6COOH) to provide a microarray platform for further covalent attachment of biomolecules. Well-defined structures in terms of wettability contrast, sharpness, and height differences between the printed and back-filled areas are confirmed by imaging null ellipsometry and microscopic wetting.
The mechanical stability and viability of molecules investigated with the atomic force microscope (AFM) continue to be limiting factors in the duration of force spectroscopy measurements. In an effort to circumvent this problem, we have fabricated an all-plastic array of over 30 000 tips with dimensions similar to common AFM probes using silicon micromolding techniques. This approach enables rapid fabrication of tip arrays with improved properties, as compared to tip arrays made entirely of silicon.