PubMed · 14809061
The source did not provide an abstract. Follow the original record for more information.
Explore connections, maps & timelines
B KEREBEL. [Peripheral mantle dentin].. https://pubmed.ncbi.nlm.nih.gov/14809061/
Cite the original work for its findings. Save a collection to share your selection of sources.
KEEP EXPLORING
The effect of sample preparation on dentin electron paramagnetic resonance (EPR) spectra was investigated. The analysis was performed on dentin samples prepared by pure mechanical treatment or by an alkaline deproteination method. It was observed that (1) mechanical treatment induces both stable and transient signals, depending on the specific mechanical operation applied; and (2) sodium hydroxide deproteination removes the native signal, but at the same time introduces new confounding signals in the EPR spectrum. Also, it increases the radiation sensitivity of dentin. These findings suggest that attention must be paid to dentin sample preparation.
Auto-degradation of collagen matrices occurs in resin-infiltrated dentine by the slow action of host-derived matrix metalloproteinases. As phosphoric acid-etching inactivates these endogenous enzymes, it is puzzling how hybrid layers created by simplified etch-and-rinse adhesives can degrade in vivo. This study tested the null hypothesis that there are no differences in the relative proteolytic activities of mineralised dentine, acid-etched dentine, and etch-and-rinse adhesive-treated acid-etched dentine. Powdered dentine prepared from extracted human teeth was treated with 17% EDTA, 10% phosphoric acid, or with five simplified etch-and-rinse adhesives that were applied to 10% phosphoric acid-etched dentine. The gelatinolytic activity of the dentine powder was assayed using fluorescein-labelled gelatine. TEM examination of the air-dried, treated dentine powder was performed to confirm the presence of remnant mineralised dentine after acid-etching. 17% EDTA significantly reduced the relative proteolytic activity (73.2%) of the untreated mineralised dentine powder (control), while 10% phosphoric acid-etched dentine exhibited the highest reduction (98.1%). Treating the acid-etched dentine powder with any of the five simplified etch-and-rinse adhesives resulted in the reactivation of the proteolytic activity, with a significant negative linear correlation (P<0.05) between the increases in fluorescence and the corresponding pH values of the adhesives. It is concluded that simplified etch-and-rinse adhesives can reactivate endogenous enzymatic activities in dentine that are previously inactivated by phosphoric acid-etching. The amount of enzyme reactivated may even exceed the original quantity present in untreated mineralised dentine. This provides an explanation for the degradation of hybrid layers after acid-etched dentine matrices are infiltrated with these adhesives.
A thick oxygen-inhibited layer (OIL) on a cured adhesive layer (AL) is believed to result in both good adaptation of composite resin (CR) and high bond strength. A high degree of conversion (DC) of the AL is also needed for durable bonding. This study evaluated the hypothesis that increasing the DC by prolonging the light-curing time of adhesive bonding resin might decrease the bond strength of the adhesive to dentin because of the subsequent thinning of the OIL thickness. The OIL thickness and the DC of solvent-removed One Step and D/E bonding resin of All Bond 2 (Bisco, USA) were measured simultaneously with FT-NIR spectroscopy according to increasing light-cure times (10, 20, 30, and 60 s) so as to evaluate their effect on the microtensile bond strength. The bonded interfaces were evaluated using scanning electron microscopy. Excessive irradiation of light-curing adhesives increased the DC, but decreased the OIL thickness. When the OIL was significantly thin by curing the adhesives for 30 or 60 s, defects were observed at the interface between the AL and the CR, as well as at the interface between the AL and the hybrid layer. When the OIL was thick, free radicals from the overlying CR may have diffused into the unreacted monomer mixtures of the OIL, chemically connecting the cured AL and the newly curing composite. It was found that to obtain maximum dentin bond strength, light-curing adhesives should be cured for the irradiation time recommended by the manufacturer.