Search PubMed⌕ Search

Biomedical subjects

Y Taira

Publications and source records attributed to Y Taira.

At least 73 records · Page 4Linked to original sources

Effects of adhesive primers on bond strength of self-curing resin to cobalt-chromium alloy.

PURPOSE: This study evaluated the effects of four adhesive primers on the shear bond strength of a self curing resin to cobalt-chromium alloy. MATERIAL AND METHODS: The adhesive primers Acryl Bond (AB), Cesead Opaque Primer (COP), Metal Primer II (MPII), and MR Bond (MRB) were used. A brass ring placed over the casting alloy disk surface nonprimed or primed with each primer was filled with the self-curing methyl methacrylate polymethyl methacrylate resin. The specimens were stored in water at 37 degrees C for 24 hours and then alternately immersed in water baths at 4 degrees C and 60 degrees C for 1 minute each for up to 20,000 thermal cycles before shear mode testing at a crosshead speed of 0.5 mm/min. RESULTS: All the primers examined improved the shear bond strength between the resin and cobalt chromium alloy compared with nonprimed specimens before thermal cycling. However, after 20,000 thermal cycles, the bond strengths of resin to cobalt chromium alloy primed with COP or MPII primers were significantly greater than those of specimens primed with AB or MRB primers and nonprimed controls. CONCLUSION: This study indicated that COP and MPII are effective primers to obtain higher bond strength between resin and cobalt-chromium alloy.

Adhesives↗

Bonding of titanium with acidic primers and a tri-n-butylborane-initiated luting agent.

Adhesive bonding of titanium was investigated with the use of five primers and two luting agents. All of the primers contained acidic methacrylate monomers for promotion of metal bonding. Titanium metal specimens were bonded with seven combinations of five primers and two luting agents. Durability of the bond was evaluated by means of thermocycling. Although all five primers enhanced the bond strength to titanium, three of the primers (Super-Bond Liquid, Metal Primer and Tokuso Rebase MR. Bond) demonstrated more durable bonds than the other two primers (Acryl Bond and All-Bond 2 Primer B). The tri-n-butylborane (TBB)-initiated luting agent exhibited better bonding ability as compared to conventional composite resin. The strongest and the most consistent bond was achieved by the combination of 4-methacryloyloxyethyl trimellitate anhydride (4-META) primer and TBB resin.

Acids↗

Malignant lymphoma arising from chronic tuberculous empyema. A case report.

We report on a case of malignant lymphoma in the chest wall, associated with chronic tuberculous empyema. CT and MR imaging showed a soft-tissue mass contiguous with the empyema and invading the chest wall. MR imaging demonstrated a difference in signal intensity between the mass and the empyema. The extent of the chest-wall lymphoma was optimally delineated on fat-suppressed contrast-enhanced MR images.

Aged↗

[An opinion from a user: a nurse's point of view].

The focus of this discussion is twofold; to provide an overview patient management in the nursing unit in relation to the Department of Examinations and to propose some strategies for assuring safe, accurate and effective laboratory tests from a nursing perspective. There are four issues identified as weaknesses in the environment of our collaboration; a lack of consistent support for anxious or frightened patients undergoing laboratory tests due to the low volume of information shared by us; a limited clinical laboratory consultation available to nurses because of unfriendly and unclear access to the Dept. of Examinations; a lack of collaboration and flexibility in responding to individual diversity in health problems; a lack of clinical laboratory coordination in scheduling laboratory tests, especially, for patients with multiple tests per day or per week. Based on those issues, five strategies are proposed. Greater involvement of medical technologists in routine laboratory works in the unit such as drawing blood and collecting specimens as needed. Clinical Laboratory tests except for urgent tests should be scheduled to minimize disturbances of life style for inpatients while waiting for the completion of all tests. An information processing system that helps nurses maintain advanced knowledge and skills is necessary to follow the state of art in the specialized area of clinical laboratory tests. It is definitely recommended that effective consultation be offered by the Dept. of Examinations. It is beneficial to patients for medical technologists to actively participate in the cooperative medicine of our hospital by sharing the patient's information with nurses in the unit. Lastly, it would be welcome to have direct communication with patients on the unit. This would facilitate mutual understanding between technologists and nurses. In conclusion, collaboration between the Department of Examinations and nurses of the unit may maximize patient benefits brought by the valuable information obtained from laboratory work through improved communication and mutual understanding.

Anxiety↗

Bonding of a cobalt-chromium alloy with acidic primers and tri-n-butylborane-initiated luting agents.

Limited information is available about chemical bonding of cobalt-chromium alloys for resin-retained fixed partial dentures. This study evaluated the effect of acidic primers on the bonding of luting agents joined to a cobalt-chromium alloy. Disk alloy specimens were bonded with eight combinations of five primers and two luting agents. Shear bond strengths were determined before and after thermocycling. The effect of priming on bond strength varied among the combinations of primer and luting agent. In particular, after thermocycling three groups demonstrated greater bond strengths than the other groups did. These were (1) specimens treated with a phosphate-methacrylate primer (Cesead Opaque Primer), (2) specimens bonded with an adhesive resin (Super-Bond Opaque), or (3) a combination of both.

Acrylic Resins↗

Effect of ultrasonic instrumentation on bond strength of three dental cements bonded to nickel-chromium alloy.

This study examined the effect of ultrasonic instrumentation on the bond strength of three types of luting material joined to a nickel-chromium alloy. Disk metal specimens were bonded together with zinc phosphate, glass ionomer, and adhesive resin luting agents. The bonded specimens were immersed in water, then vibrated with an ultrasonic unit for 0 to 5 minutes. The shear bond strength in the 0 or nonvibrated group was 50.1 MPa for adhesive resin, 18.4 MPa for glass ionomer, and 4.7 MPa for zinc phosphate cement. Vibration for a period of 5 minutes significantly diminished the bond strength of adhesive resin and glass ionomer materials, whereas the bond strength of zinc phosphate cement was affected after only 1 minute.

Acrylic Resins↗

Malignant fibrous histiocytoma of the esophagus.

A 78-year-old man presented with an esophageal polyp that was confirmed by immunohistochemistry and electron microscopy to be malignant fibrous histiocytoma. The tumor was comprised of a proliferation of spindle-shaped cells admixed with bizarre giant cells. These tumor cells were immunoreactive for smooth muscle actin, vimentin, alpha-1-anti-chymotrypsin and CD68. Electron microscopic examination revealed the myofibroblastic and histiocytic features of the tumor cells. No elements of epithelial or myogenic differentiation were found in the tumor. Malignant fibrous histiocytoma of the esophagus is extremely rare, with 10 cases being documented so far in the literature. The differential diagnosis of pleomorphic tumors of the esophagus is discussed.

Aged↗

Effect of proximal arterial perfusion pressure on function, spinal cord blood flow, and histopathologic changes after increasing intervals of aortic occlusion in the rat.

BACKGROUND AND PURPOSE: Cross-clamping of the thoracic aorta results in spinal cord ischemia and prominent systemic hypertension. Using a rat model of transient spinal cord ischemia. we examined the effects of manipulation of proximal aortic blood pressure on spinal cord blood flow (SCBF), neurological dysfunction, and changes in spinal histopathology after increasing intervals of aortic occlusion. METHODS: Aortic occlusion was induced by the inflation of a 2F Fogarty catheter placed into the thoracic aorta in rats anesthetized with halothane (1.5%). A tail artery was cannulated to monitor distal arterial pressure (DAP). To measure SCBF, a laser probe was implanted into the epidural space of the L-2 vertebra. To manipulate proximal arterial pressure (PAP), the left carotid artery was cannulated with a 20-gauge polytetrafluoroethylene catheter to permit blood withdrawal and infusion from a peripheral reservoir during aortic occlusion. In a survey study, spinal cord ischemia was induced in single animals at intervals of 6, 10, 15, 30, or 40 minutes with PAP controlled at 40, 60, 80, and 110 to 120 mm Hg. In a second series, ischemia was induced in groups of animals for 0, 6, 8, 10, and 12 minutes with PAP controlled at 40 mm Hg. After ischemia the animals survived for 2 to 3 days. During this recovery period, neurological functions were evaluated, followed by quantitative histopathology of the spinal cord. RESULTS: Under normal conditions, cross-clamping yields an acute proximal hypertension (125 to 135 mm Hg), a fall of DAP to 15 to 22 mm Hg, and a decrease in SCBF to 7% to 11% of baseline values. With the use of the external reservoir, proximal hypertension could be abolished and the PAP maintained at target pressures. In these studies a typical syndrome of tactile allodynia, spastic paraplegia, and necrotic changes affecting the central part of the gray matter after 24 to 48 hours of reperfusion was observed at the following combinations of ischemic intervals and PAP values: > 10 minutes/40 mm Hg; > 12 minutes/60 mm Hg; > 16 minutes/80 mm Hg; and > 30 minutes/uncontrolled. Lowering PAP resulted in a corresponding decrease in residual SCBF. Systematic studies at a PAP of 40 mm Hg at occlusion intervals of 6, 8, 10, and 12 minutes revealed that 100% of rats were paraplegic after 10- and 12-minute ischemia, and these rats showed corresponding signs of spinal histopathology. CONCLUSIONS: The present study shows that systemic intraischemic hypotension (40 mm Hg) significantly potentiates neurological dysfunction after transient aortic occlusion. The mechanism of the observed effect may include elimination of collateral flow during aortic occlusion and/or consequent potentiation of hypoperfusion during reperfusion. These data indicate that PAP during occlusion should be monitored and/or controlled because it is a critical variable in the determination of outcome in this model of spinal cord ischemia.

Animals↗

Adhesive bonding to dentin with ferrous chloride primers and tri-n-butylborane-initiated luting agents.

A variety of surface modifications with metal chlorides has been used to enhance the bond of resins to dentin. This study investigated the effectiveness of ferrous chloride in terms of the initiation of polymerization in dentin bonding. The efficacy of experimental dentin primers was evaluated via the bonding of two luting agents to dentin. The 16 primers evaluated were ferrous chloride (FeCl2) aqueous solutions, eight with and eight without 35% 2-hydroxyethyl methacrylate (HEMA). The concentrations of FeCl2 in the primers ranged from 2.0 x 10(-6) to 5.0 x 10(-4) mol/g. One luting agent (Super-Bond C&B) consisted of methyl methacrylate (MMA), 4-methacryloyloxyethyl trimellitate anhydride (4-META), and tri-n-butylborane (TBB) initiator. The other luting agent was prepared with MMA and TBB, but without 4-META. Bovine dentin surfaces were flattened, etched with an aqueous solution of 10% phosphoric acid, primed, and then bonded with stainless steel rods. Tensile strengths of the bonded specimens were measured after one-day immersion in water. Tensile testing revealed that the bond strength was influenced by the application of FeCl2 and/or HEMA. The maximum bond strength of 33.0 MPa was recorded with the use of primer containing FeCl2 and HEMA in MMA-TBB resin. In the case of Super-Bond, only surface treatment of dentin with aqueous primers containing 5.0 x 10(-5) to 2.0 x 10(-4) mol/g ferrous chloride resulted in bond strength values above 22.0 MPa. This bonding technique, combining the use of ferrous chloride primer with Super-Bond resin, may potentially be applied for seating resin-bonded restorations.

Analysis of Variance↗

Fentanyl pretreatment attenuates the haemodynamic response to sudden inhalation of 5% isoflurane.

High concentrations of inhaled isoflurane can increase heart rate and/or arterial pressure. The purpose of this study was to determine whether fentanyl has a prophylactic effect on the isoflurane-induced circulatory response in adult patients. Thirty patients due to undergo elective surgery were randomly allocated to one of three groups of ten patients. Prior to surgery, one group inhaled 2.5% isoflurane, another inhaled 5.0% isoflurane, and the third group inhaled 5.0% isoflurane and were given fentanyl 2 micrograms.kg-1 i.v. two minutes before induction of anaesthesia. Anaesthesia was induced with thiamylal followed by vecuronium. The lungs were ventilated with 100% oxygen and either 2.5% or 5.0% isoflurane via face mask. Ventilation was continued for five minutes. Heart rate (HR) and mean arterial pressure (MAP) were recorded at two minutes before induction of anaesthesia (baseline), immediately before the induction of anaesthesia, and at three and five minutes after induction, respectively. It was found that 5.0% isoflurane caused an increase in HR compared with baseline (P < 0.01) and with the 2.5% isoflurane (P < 0.05): 2.5% isoflurane did not elicit this response. An increase was also noted in MAP, compared with the 2.5% isoflurane (P < 0.01): 2.5% isoflurane did not elicit this increase. Fentanyl pretreatment attenuated the increases in HR and in MAP that occurred with 5.0% isoflurane (P < 0.01). These results suggest that fentanyl attenuates the enhancement of both HR and MAP from face mask inhalation of a high concentration of isoflurane.

Adult↗

Primer for bonding resin to metal.

OBJECTIVES: The purpose was to examine the effect on the bond strength and durability of a resin bond to metal of modification of a primer consisting of thiophosphoric methacrylate with phosphoric methacrylates and/or benzoyl peroxide. METHODS: Acrylic rods were bonded with a luting resin consisting of poly(methyl methacrylate) powder and a mixture of methyl methacrylate and tributylborane initiator to silver-palladium alloy (Ag-Pd), gold-silver alloy (Au-Ag), cobalt-chromium alloy (Co-Cr), and titanium (Ti) surfaces treated with various primers. The bonded samples were thermocycled for 2,000 cycles and the mean bond strengths were compared using one-way ANOVA and Duncan's new multiple range test at p < 0.05. RESULTS: Using primers of thiophosphoric methacrylate or phosphoric methacrylates alone, the bond strengths of Ag-Pd decreased significantly (p < 0.05) after thermocycling. The durability was significantly improved (p < 0.05) when thiophosphoric methocrylate was used in combination with the phosphate monomers. The additional use of benzoyl peroxide and heat treatment resulted in a significant increase (p < 0.05) in the durability of two groups; the mean bond strengths over 20 MPa and the lowest values remained unchanged even after 2,000 thermocycles. SIGNIFICANCE: The highest level of bond strength and durability to dental noble metals was achieved using a mixture of thiophosphoric and phosphoric methacrylates and benzoyl peroxide. These bond strength results are comparable to values obtained for base metals.

Acetone↗

Adhesive bonding of titanium with a methacrylate-phosphate primer and self-curing adhesive resins.

The adhesive bonding of titanium was evaluated with the use of a metal primer and three types of self-curing luting agent. The primer contained 10-methacryloyloxydecyl dihydrogen phosphate (MDP). One luting agent was a composite material that contained the MDP monomer in its liquid part. The other luting agent was based on methyl methacrylate (MMA), initiated with tri-n-butylborane derivative (TBB), and contained 4-methacryloxyethyl trimellitate anhydride (4-META). The MMA-TBB resin without 4-META was used for the control. Pure titanium metal specimens were bonded with various combinations. Shear bond strengths were determined after repeated thermocycles in water. Both MDP and 4-META were effective in bonding titanium. The decrease in bond strength was minimum when the titanium was primed with MDP and then bonded with the TBB-initiated resins.

Acrylic Resins↗

[Surgical treatment of posterior mediastinal teratoma].

A 22-year-old male patient was admitted to our hospital because of an abnormal shadow on a chest X-ray taken for routine examination. Preoperative diagnostic work up including chest computed tomography and magnetic resonance imaging suggested that the tumor would most likely to be a posterior mediastinal lipoma. Through a right thoracotomy the tumor was removed successfully. Histologically it proved to be a mature teratoma. The incidence, etiology and diagnostic procedure of the mediastinal teratoma was discussed.

Adult↗

Epidemiological and ecological studies of Japanese encephalitis in Okinawa, subtropical area in Japan. II. Prevalence of Japanese encephalitis antibody in residents in Okinawa, Miyako and Ishigaki islands.

During 1989 to 1990, human sera were collected by age groups in Okinawa (the northern, central and southern areas), Miyako and Ishigaki islands and examined for the neutralization (N) antibodies to two strains, Nakayama (vaccine strain) and C307 (Okinawan strain), of Japanese encephalitis (JE) virus. In Okinawa island, the N antibody positive rate to C307 was higher than that to Nakayama, while in Miyako and Ishigaki islands, the positive rate to Nakayama was higher than that to C307, suggesting that JE virus transmission rate was higher in Okinawa than in Miyako and Ishigaki islands. In Okinawa Prefecture, JE vaccine had not been administered to most of residents over 31 years of age at the time of serum collection. In residents over 31 years old, the positive rate to C307 was highest in the north of Okinawa (83.3%) and was lowest in Miyako (26.3%), with the second lowest in Ishigaki (33.3%). The distribution of N antibody titers to C307 gave hyperbolic patterns in the 0-5 age groups in Miyako and Ishigaki, and also in the 31-40, 41-50 age groups in Miyako and the 41-50 age group in Ishigaki, suggesting low rates of natural infection in these 4-5 decades in both islands. In residents of ages subjected to JE vaccine, a characteristic pattern was obtained, in which the curves to Nakayama shifted to higher titers than those to C307, suggesting that the first antigenic stimulation was caused by vaccine, not by natural infection of JE virus.

Adolescent↗

Effect of primers containing copper salts on bonding of TBB resin to enamel.

The effect of primers containing copper salts on adhesion between enamel and stainless steel was studied in a trial to improve durability of TBB type resin cements. Bovine enamel surfaces were treated with 10% phosphoric acid, then with acetone primers containing copper salts, and finally bonded with TBB resins. Tensile strengths of the bonded specimens were measured after thermocycling testing in water and compared with those obtained for commercial composite type resin cements. A combination of a primer containing copper (II) methacryloyloxyethyl succinate and 4-META/MMA-TBB resin was most effective in improving the durability, and superior to the commercial resin cements. The mean and lowest bond strength values of 21 MPa and about 12 MPa, respectively, were retained after 2,000 thermocycles.

Acrylic Resins↗

[Effects of in vivo pretreatment with various barbiturates on lidocaine metabolism in rat liver microsomes].

In male Wistar rats, we studied the effects of in vivo pretreatment with phenobarbital (PB), amobarbital (AB), hexobarbital (HB), pentobarbital (PT) or thiamylal (TI) on hepatic microsomal enzymes, and on deethylation of lidocaine in the microsomes. The rats of pretreatment groups received 0.1 ml of the above barbiturates (320 mumol.kg-1) and the control group received intramuscular injection of 0.9 % NaCl solution for 4 days. NADPH-cytochrome C reductase of the PB and AB groups increased significantly in activity and cytochrome b5 of only PB group increased in content. After the pretreatment with PB, TI produced higher microsomal cytochrome P-450 contents than in the control group. The potency of P-450 induction was in descending order of PB, TI, AB, HB and PT. Also we found the positive linear relationship between the potency of P-450 induction and the elimination half time (t1/2 beta) of the barbiturates. The activities of lidocaine deethylase with microsomes per P-450 of the pretreated rats with these five barbiturates (PB, AB, HB, PT and TI) were 2.4, 1.9, 2.2, 1.5 and 2.2 times of control values, respectively. Based on these results, we conclude that lidocaine deethylase activity of P-450 is increased by these five barbiturates whether levels of P-450 are increased quantitatively, or not.

Animals↗

Effect of adhesive metal primers on bonding a prosthetic composite resin to metals.

The effect of three adhesive metal primers on the shear bond strength of a light-cured prosthetic composite resin bonded to cobalt-chromium or silver-palladium-copper-gold casting alloy was evaluated. The adhesive metal primers used were New Metacolor opaque bonding liner, Cesead opaque primer, and 0.5% VBATDT in acetone. A newly prepared light-cured opaque resin was used to bond a light-cured veneering resin to dental alloys. The specimens were thermocycled in water for up to 20,000 cycles between 4 degrees C and 60 degrees C, and shear bond strengths were recorded. The light-cured composite resin bonded most strongly to Co-Cr alloy primed with Cesead primer and to Ag-Pd-Cu-Au alloy with the VBATDT primer. These adhesive metal primers may be clinically acceptable for bonding a light-cured prosthetic composite resin to base or precious metal.

Adhesives↗

[The anesthetic management for adrenalectomy of a patient with Cushing's syndrome in pregnancy].

The anesthetic management for left adrenalectomy of a pregnant patient with Cushing's syndrome caused by adrenal adenoma during pregnancy was reported. At 21 week gestation, anesthesia was induced with modified NLA and maintained with nitrous oxide-enflurane-oxygen combined with continuous lumbar epidural anesthesia. Postoperatively, she was delivered a normal, 1990 g infant at 37 week gestation. The present case is believed to be the first reported case of general anesthesia in detail for adrenalectomy in a patient with Cushing's syndrome during pregnancy. The anesthetic management including choice of anesthetics, anesthetic method, intraoperative monitoring, influence of catecholamine, and fetal as well as maternal complication was reviewed from literatures.

Adenoma↗