Search PubMed⌕ Search

Biomedical subjects

V P Thompson

Publications and source records attributed to V P Thompson.

At least 37 records · Page 2Linked to original sources
PubMed1994

Sandblasting and silica coating of a glass-infiltrated alumina ceramic: volume loss, morphology, and changes in the surface composition.

Silica coating can improve bonding of resin to glass-infiltrated aluminum oxide ceramic (In-Ceram), and sandblasting is a pretreatment to thermal silica coating (Silicoater MD system) or a tribochemical coating process (Rocatec system). This study evaluated the effects of sandblasting and coating techniques on volume loss, surface morphology, and surface composition of In-Ceram ceramic. Volume loss through sandblasting was 36 times less for In-Ceram ceramic compared with a feldspathic glass ceramic (IPS-Empress), and sandblasting of In-Ceram ceramic did not change its surface composition. After tribochemical coating with the Rocatec system, a layer of small silica particles remained that elevated the silica content to 19.7 weight percentage (energy-dispersive spectroscopy). Ultrasonic cleaning removed loose silica particles from the surface and decreased the silica content to 15.8 weight percentage, which suggested firm attachment of most of the silica layer to the surface. After treatment with the Silicoater MD system, the silica content increased only slightly from that of the sandblasted specimen. The silica layer created by these systems differs greatly in both morphology and thickness, which could result in different bond strengths. Sandblasting of all ceramic clinical restorations with feldspathic glass materials should be avoided, but for In-Ceram ceramic the volume loss was within an acceptable range and similar to that of noble metals.

Aluminum Oxide↗
PubMed1994

Influence of prolonged thermal cycling and water storage on the tensile bond strength of composite to NiCr alloy.

OBJECTIVES: The purpose of this study was to evaluate the bond strength and bond durability of new adhesive systems (both micromechanical and chemo-mechanical) to a beryllium-free nickel-chromium alloy (NiCr). METHODS: Plexiglass tubes filled with composite were bonded to NiCr alloy discs. Groups of 24 samples were bonded using six different bonding systems. Subgroups of eight bonded samples were stored in an isotonic artificial saliva solution (37 degrees C) either for 1 d, 30 d or 150 d. In addition, the 30 and 150 d samples were thermal cycled for 7,500 or 37,500 cycles, respectively. RESULTS: The bond strength of a conventional BisGMA composite to sandblasted NiCr was statistically significantly lower than that of chemo-mechanical bonding systems and decreased continuously during the storage time of 150 d. The additional use of a silane on the sandblasted alloy resulted only in a slight, statistically insignificant increase in bond strength. Statistically significantly higher and more durable bonds to NiCr alloy were achieved either with the combination of silica coating and use of a conventional BisGMA composite or with the combination of sandblasting and the use of a composite modified with a phosphate monomer. In these systems, the bond strengths were limited by the cohesive strength of the resin composites. However, a newly developed composite containing the same active phosphate monomer showed a statistically significant decrease in bond strength (cohesive strength) over storage time. SIGNIFICANCE: Longer-term storage times in a wet environment are needed in laboratory tests to examine the durability of bonding systems.

Bisphenol A-Glycidyl Methacrylate↗
PubMed1994

Effects of sandblasting and silica-coating procedures on pure titanium.

Silica coating titanium improves chemomechanical bonding. Sandblasting is recommended as a pretreatment to thermal silica coating (Silicoater MD) or as part of a tribochemical silica coating process (Rocatec). This study evaluated the effects of sandblasting and coating techniques on volume loss, surface morphology and composition changes in pure titanium. Volume loss of titanium was similar to values reported for base alloys and does not seem to be critical for the clinical fit of restorations. Embedded alumina particles were found in the titanium after sandblasting and the alumina content increased to a range of 27.5-39.3 wt% as measured by EDS. Following tribochemical silica coating, a layer of small silica particles remained on the surface, increasing the silica content to a range of 17.9-19.5 wt%. Ultrasonic cleaning removed loose alumina or silica particles from the surface, resulting in only slight decreases in alumina or silica contents, suggesting firm attachment of most of the alumina and silica to the titanium surface. Silica content following thermal silica coating treatment increased only slightly from the sandblasted specimen to 1.4 wt%. The silica layer employed by these silica coating methods differs widely in both morphology and thickness. These results provide a basis for explanation of adhesive failure modes in bond strength tests and for developing methods to optimize resin bonding. Clinically, ultrasonic cleaning of sandblasted and tribochemically silica coated titanium should improve resin bonding as loose surface particles are removed without relevant changes in composition.

Aluminum Oxide↗
PubMed1993

Sandblasting and silica-coating of dental alloys: volume loss, morphology and changes in the surface composition.

Silica-coating alloys improves chemo-mechanical bonding. Sandblasting is recommended as pretreatment to thermal silica-coating or as part of a tribochemical silica-coating process. This study evaluated the effects of sandblasting and coating techniques on volume loss, surface morphology and compositional changes in noble (AuAgCu) and base alloys (NiCr and CoCr). Volume loss was statistically significantly higher in the noble as compared to the base alloys but does not seem to be critical for the clinical fit of restorations. Embedded alumina particles were found in all alloys after sandblasting and the alumina content increased to a range of 14 to 37 wt% as measured by EDS. Following tribochemical silica-coating, a layer of small silica particles remained on the surface, increasing the silica content to between 12 and 20 wt%. Ultrasonic cleaning removed loose alumina or silica particles from the surface, resulting in only slight decreases in alumina or silica contents, thus suggesting firm attachment of the major part of alumina and silica to the alloy surface. Clinically, ultrasonic cleaning of sandblasted and tribochemically silica-coated alloys might improve resin bonding as loose surface particles are removed without relevant changes in composition. Silica content following thermal silica-coating treatment increased only slightly from the sandblasted specimen. The silica layer employed by these silica-coating methods differs widely in both morphology and thickness. These results provide a basis for explanation of adhesive failure modes in bond strength tests which will possibly optimize resin bonding. Further research is needed to characterize the outermost surface layers after these treatments and the exact location of adhesive failures.

Analysis of Variance↗
PubMed1993

Resin-bonded prosthodontics. An update.

First-generation designs that covered a large area of enamel but had minimal retentive features still provided sufficient longevity to be classified as "permanent" type restorations. The goal of long-term service can be realized more consistently by incorporating second-generation designs with the ease of adhesive bonding.

Dental Bonding↗
PubMed1991

A 5- and 8-year clinical evaluation of a posterior composite resin.

Class I and II posterior composite resin (Ful-Fil) restorations were placed and were clinically evaluated, according to the US Public Health Service criteria, at baseline, 6 months, 5 years, and 8 years. At 5 years/8 years, alpha scores were assigned to the following percentages of restorations: 16%/31% for color match; 65%/62% for marginal discoloration; 74%/54% for cavosurface marginal discoloration; 100%/100% for axial contour; and 81%/65% for anatomic form. At 5 years/8 years, 56%/33% of Class II restorations had tight proximal contacts; 45%/44% had light contacts; and 0%/22% had no contacts. Transient postoperative sensitivity was reported in 6% of the restorations. Indirect evaluation indicated that there was an average of 64 +/- 35 microns of wear at baseline (because of overfinishing), 105 +/- 67 microns at 6 months, 217 +/- 76 microns at 5 years, and 253 +/- 82 microns at 8 years. At 5 years, three of the restorations, and at 8 years, four additional restorations, were clinically unacceptable because of recurrent caries and/or excessive wear. Final success rates of 90% and 77% at 5 and 8 years, respectively, were calculated.

Adult↗
PubMed1983

Resin-bonded retainers. Part I: Resin bond to electrolytically etched nonprecious alloys.

Nonprecious Ni-Cr casting alloys can be electrolytically etched to yield a highly retentive surface for micromechanical bonding of dental resins. The acid, current density, and etching time to achieve the retentive features are specific for each alloy. Conditions for etching one beryllium-containing and one non-beryllium-containing alloy are described. The tensile strength of a resin system to these alloys has been determined to be over two times the accepted value of the resin bond to acid-etched enamel.

Acid Etching, Dental↗
PubMed1979

Dental resins with reduced shrinkage during hardening.

Unsaturated spiro-orthocarbonates are monomers that expand on polymerization and will co-polymerize with conventional BIS-GMA based resins. This combination has good physical properties and bonding to enamel with some polymerization expansion evident at 50 C. Dispersion of the carbonate in microcrystalline form in liquid monomer appears to be a method to allow its reaction in the initial polymerization.

Adhesiveness↗