Search PubMed⌕ Search

Biomedical subjects

V C Mow

Publications and source records attributed to V C Mow.

At least 55 records · Page 3Linked to original sources

Differences in patellofemoral joint cartilage material properties and their significance to the etiology of cartilage surface fibrillation.

OBJECTIVE: To determine if differences in biomechanical properties and biochemical composition exist between human patellar articular cartilage and the opposing femoral articular cartilage. DESIGN: The biomechanical properties and biochemical composition of the articular cartilage of 17 knees from 13 donors were determined for four sites on the patella and three sites on the femur representing regions of contact at 30 degrees and 90 degrees of flexion. The material properties were determined by biphasic indentation testing, yielding the compressive aggregate modulus, HA, permeability, k, and Poisson's ratio, vs. The thickness of the cartilage at the indentation site, h, was also measured using a needle probe. Full-thickness samples of cartilage adjacent to each indentation site were used for wet weight, sulfated glycosaminoglycan content and hydroxyproline content determinations. RESULTS: The patellar cartilage was found to have a lower compressive aggregate modulus by 30% (P < 0.001), higher permeability to fluid flow by 66% (P < 0.001) and greater thickness by 23% (P = 0.017) than that of the opposing femoral cartilage. The Poisson's ratios for both surfaces were found to be nearly zero. The water content of the patella was higher by 5% (P = 0.031) and the proteoglycan content lower by 19% (P = 0.030) than that of the femur. However, no differences were found between the collagen contents of the cartilages. CONCLUSIONS: Significant differences were found between the intrinsic material properties of the patellar cartilage and those of the femoral-trochlear cartilage. This variability of cartilage material properties with the patellofemoral joint may help explain why patellar cartilage has been frequently observed clinically to exhibit earlier and more severe fibrillation changes than the opposing femoral cartilage.

Adolescent↗

Is the nucleus pulposus a solid or a fluid? Mechanical behaviors of the nucleus pulposus of the human intervertebral disc.

STUDY DESIGN: A new technique to measure the viscoelastic behavior of the nucleus pulposus in shear was used to assess its solid and fluid characteristics. OBJECTIVES: To review existing knowledge on mechanical behaviors of the nucleus pulposus, and to develop a new technique to study the viscoelastic behaviors of isolated nucleus pulposus samples in torsional (pure) shear under transient and dynamic conditions. SUMMARY OF BACKGROUND DATA: Numerous studies have investigated the swelling behavior of the nucleus and found the swelling pressure to range approximately 0.05-3 MPa, depending on loading conditions. Very few studies, however, have investigated the load-deformational behaviors of the nucleus pulposus. METHODS: Thirteen nondegenerate samples of nucleus pulposus were harvested from lumbar discs and tested in torsional shear under transient and dynamic test conditions. A linear viscoelastic law with variable amplitude relaxation and dynamic frequency sweep experiments. The coefficients of the viscoelastic law were determined from the stress relaxation experiments, whereas the dynamic shear modulus and phase shift angle were determined from the frequency sweep. RESULTS: The nucleus exhibits significant viscoelastic effects in shear. Under transient conditions, the stress relaxed to values near zero, which is indicative of the "fluid-like" behaviors of the nucleus. Under dynamic conditions, however, the material parameters for the nucleus, magnitude of the complex modulus (7-21 kPa), and phase angle (23-31 degrees) were more characteristic of a viscoelastic solid. The authors' proposed stress-strain law exhibited excellent agreement with the viscoelastic data. CONCLUSIONS: In response to shear deformations, the nucleus pulposus exhibited significant viscoelastic effects, characteristic of a fluid and a solid. Whether the nucleus pulposus behaves more as a fluid or a solid in vivo depends on the rate of loading.

Biomechanical Phenomena↗

Tensile properties of nondegenerate human lumbar anulus fibrosus.

STUDY DESIGN: The in vitro tensile behavior of multiple-layer samples of anulus fibrosus were investigated from nondegenerate intervertebral discs. OBJECTIVES: To quantify the intrinsic tensile behavior of nondegenerate anulus fibrosus and the variations with position and age in the intervertebral disc. SUMMARY OF BACKGROUND DATA: Tension is an important loading mode in the anulus fibrosus. The tensile behavior of single- and multiple-layer samples of anulus fibrosus has been shown to vary with specimen orientation, position in the disc, and environmental conditions. Little is known of the changes in these site-specific tensile properties of the anulus with aging or degeneration of the intervertebral disc. METHODS: Multiple-layer specimens of anulus fibrosus were harvested with an orientation parallel to the circumference of the disc. Constant strain rate and uniaxial tensile tests were performed in 0.15 mol/l NaCl at slow strain rates to measure the intrinsic properties of the collagen-proteoglycan matrix of the anulus fibrosus. The tensile modulus, failure stress, failure strain, and strain energy density were determined. Statistical analyses were done to evaluate regional and age-related differences in these properties. RESULTS: Significant radial and circumferential variations in the intrinsic tensile properties of anular samples were detected. The anterior anulus fibrosus had larger values for tensile moduli and failure stresses than the posterolateral anulus. Also, the outer regions of the anulus had greater moduli and failure stresses and lower failure strains than the inner regions. Strain energy density did not vary significantly with region. Significant, but very weak, correlations were detected between tensile properties and age of the intervertebral disc. CONCLUSIONS: The observed variations in tensile behavior of multiple-layer anulus samples indicate that larger variations in tensile modulus and failure properties occur with radial position in the disc than from anterior to posterolateral regions. This pattern is likely related to site-specific variations in the tensile properties of the single-layer samples of anulus fibrosus lamellae and the organization of successive lamellae and their interactions. The results of the present study suggest that factors other than age, such as compositional and structural variations in the disc, are the most important determinants of tensile behavior of the anulus fibrosus.

Adult↗

Determination of collagen-proteoglycan interactions in vitro.

The objective of this study was to characterize the physical interactions of the molecular networks formed by mixtures of collagen and proteoglycan in vitro. Pure proteoglycan aggrecan solutions, collagen (type II) suspensions and mixtures of these molecules in varying proportions and concentrations were subjected to viscometric flow measurements using a cone-on-plate viscometer. Linear viscoelastic and non-Newtonian flow properties of these solutions and suspensions were described using a second-order statistical network theory for polymeric fluids (Zhu et al., 1991, J. Biomechanics 24, 1007-1018). This theory provides a set of material coefficients which relate the macroscopic flow behavior of the fluid to an idealized molecular network structure. The results indicated distinct differences between the flow properties of pure collagen suspensions and those of pure proteoglycan solutions. The collagen network showed much greater shear stiffness and more effective energy storage capability than the proteoglycan network. The relative proportion of collagen to proteoglycan is the dominant factor in determining the flow behavior of the mixtures. Analysis of the statistical network theory indicated that the collagen in a collagen-proteoglycan mixture enhances molecular interactions by increasing the amount of entanglement interactions and/or the strength of interaction, while aggrecan acts to reduce the number and/or strength of molecular interactions. These results characterize the physical interactions between type II collagen and aggrecan and provide some insight into their potential roles in giving articular cartilage its mechanical behavior.

Aggrecans↗

Glenohumeral stability. Biomechanical properties of passive and active stabilizers.

The shoulder is characterized foremost by its mobility and large range of motion. The glenohumeral joint is notable for its relative lack of bony constraint, relying heavily on the congruent articulating surfaces and surrounding soft tissue envelope for static and dynamic stability. Effective function in the articulation is achieved by a complex interaction between the various articular and soft tissue restraints. The rotator cuff muscles center the humeral head in the congruent glenoid fossa through the midrange of motion, when the capsuloligamentous structures are lax. However, incongruent joints, especially in positions of loading asymmetry (in external rotation), have larger translations that occur at the extremes of motion. Excessive translations are then effectively restricted by the mechanical properties of the inferior glenohumeral ligament. When the capsule is tightened anteriorly it results in an anterior tether and causes an associated posterior shift in contact on the glenoid. The posterior migration of the humeral head center and glenohumeral contact are again more pronounced in shoulders with reduced congruence. Additional studies of normal motion in different planes, the effects of rotator cuff pathology and dysfunction on the kinematics of the joint, proprioception of the capsule, and biomechanical tests of the inferior glenohumeral ligament and other components of the joint capsule at strain rates associated with injury, need to be conducted to understand the specifics of normal shoulder function and the pathophysiologic processes that occur during shoulder degeneration.

Biomechanical Phenomena↗

Degeneration and aging affect the tensile behavior of human lumbar anulus fibrosus.

STUDY DESIGN: Samples of human lumbar (L3-L4) anulus fibrosus from four different anatomic sites (anterior outer, posterolateral inner), ranging from normal to severely degenerate, were studied in uniaxial tension and measured for water content. OBJECTIVES: To evaluate the effects of aging and degeneration on the tensile properties and hydration of the anulus fibrosus in a site-specific manner. The relationship between hydration and parameters of the tensile behavior were investigated. SUMMARY OF BACKGROUND DATA: Degeneration and aging have been shown to be related to dramatic changes in the composition and structure of the anulus fibrosus. The associated changes in the tensile, compressive, and shear properties of the anulus fibrosus have not been documented. Numerical studies using finite element models have attempted to simulate the degenerative process by incorporating estimated mechanical properties meant to represent the degenerate anulus fibrosus. Their results present findings that suggest that altered material properties of the anulus fibrosus affect the mechanics of the entire intervertebral disc. METHODS: Samples of human lumbar anulus fibrosus were classified by grade of degeneration based on a morphologic grading scheme. Multiple layer anulus specimens from four sites in the disc were tested in uniaxial tension under quasistatic conditions in a physiologic saline bath. The tensile modules, Poisson's ratio, failure stress and strain, the strain energy density to failure, and the corresponding hydration were determined for each sample. RESULTS: The Poisson's ratio, failure stress, and strain energy density of the anulus fibrosus were found to be affected significantly by degeneration, with some evidence of a sensitivity of the tensile modulus to grade of degeneration. All material properties were found to exhibit a significant and greater dependence on site within the disc than on degenerative grade. Weak correlations between aging and the Poisson's ratio and strain energy density were observed. Water content of anulus fibrosus tissue was not affected by degeneration or aging, although correlations with tensile properties were observed. CONCLUSIONS: The dramatic changes in morphology, composition, and structure that occur in anulus fibrosus with aging and degeneration are accompanied by specific variations in the tensile properties, which were generally small in magnitude. Position of the anulus fibrosus within the intervertebral disc, particularly in the radial direction, appeared to be the most important variable affecting anulus fibrosus tensile properties. This dependence on position did not change with either aging or degeneration. Results from the present study may be useful in future finite element models to assess how altered material properties of the anulus fibrosus during degeneration and aging may affect the mechanics of the entire intervertebral disc.

Adolescent↗

Chondrocyte deformation and local tissue strain in articular cartilage: a confocal microscopy study.

It is well accepted that mechanical forces can modulate the metabolic activity of chondrocytes, although the specific mechanisms of mechanical signal transduction in articular cartilage are still unknown. One proposed pathway through which chondrocytes may perceive changes in their mechanical environment is directly through cellular deformation. An important step toward understanding the role of chondrocyte deformation in signal transduction is to determine the changes in the shape and volume of chondrocytes during applied compression of the tissue. Recently, a technique was developed for quantitative morphometry of viable chondrocytes within the extracellular matrix using three-dimensional confocal scanning laser microscopy. In the present study, this method was used to quantify changes in chondrocyte morphology and local tissue deformation in the surface, middle, and deep zones in explants of canine articular cartilage subjected to physiological levels of matrix deformation. The results indicated that at 15% surface-to-surface equilibrium strain in the tissue, a similar magnitude of local tissue strain occurs in the middle and deep zones. In the surface zone, local strains of 19% were observed, indicating that the compressive stiffness of the surface zone is significantly less than that of the middle and deep zones. With this degree of tissue deformation, significant decreases in cellular height of 26, 19, and 20% and in cell volume of 22, 16, and 17% were observed in the surface, middle, and deep zones, respectively. The deformation of chondrocytes in the surface zone was anisotropic, with significant lateral expansion occurring in the direction perpendicular to the local split-line pattern. When compression was removed, there was complete recovery of cellular morphology in all cases. These observations support the hypothesis that deformation of chondrocytes or a change in their volume may occur during in vivo joint loading and may have a role in the mechanical signal transduction pathway of articular cartilage.

Animals↗

Contact areas in the thumb carpometacarpal joint.

The thumb carpometacarpal joint is a common site of osteoarthritis. It has been hypothesized that peaks of localized stress on the dorsoradial or volar-ulnar regions, or both, of the articular surfaces of the trapezium and metacarpal lead to erosion of cartilage and may be responsible for the progression of the disease. The objective of this study was to determine the contact areas in this joint under the functional position of lateral (key) pinch and in the extremes of range of motion of the joint. These contact areas were assessed relative to the observed sites of cartilage thinning. Eight hands from cadavers of women and five from cadavers of men were tested in vitro with the thumb under a 25 N load in the lateral pinch position, and under small muscle loads (0-5 N) with the thumb in flexion, extension, abduction, adduction, and neutral positions. Contact areas of articular surfaces of the thumb carpometacarpal joint were determined for these positions using a stereophotogrammetric technique. The lateral pinch position produced contact areas predominantly on the central, volar, and volar-ulnar regions of the trapezium and the metacarpal. In three specimens, contact areas were distinctly separated between the dorsoradial and volar-ulnar regions, and in one specimen, from a man, contact occurred exclusively on the dorsoradial region of the trapezium. Using stereophotogrammetry, maps of cartilage thickness also were determined for a subset of nine specimens. The volar-ulnar, ulnar, and dorsoradial regions of the trapezium were the most common sites of thin cartilage, and these may be sites of cartilage wear.(ABSTRACT TRUNCATED AT 250 WORDS)

Aged↗

Mechanical behavior of articular cartilage in shear is altered by transection of the anterior cruciate ligament.

The flow-independent viscoelastic and equilibrium behaviors of canine articular cartilage were examined with time after transection of the anterior cruciate ligament. The equilibrium, transient, and dynamic shear behaviors of cartilage were studied in biaxial compression-torsion testing at two time periods after transection of the anterior cruciate ligament and at two sites on the femoral condyle, in order to test for differences between sites of frequent and less frequent contact. Water content also was measured in cartilage at sites corresponding to the areas of mechanical testing. Transection of the anterior cruciate ligament produced significant decreases in all measured moduli of articular cartilage tested in equilibrium and dynamic shear and in equilibrium compression; the values for these moduli were 61, 56, and 77% of the control values, respectively, beginning at 6 weeks following transection of the anterior cruciate ligament. There was evidence of increased energy dissipation of cartilage in shear, with a 13 and 35% increase in tan delta at 6 and 12 weeks after transection of the anterior cruciate ligament, respectively. Changes in the viscoelastic relaxation function of cartilage in shear also were evident at 12 weeks after surgery. In all tissue, there was a significant increase in hydration of approximately 4% at 6 or 12 weeks after surgery. There was little difference between the material parameters for areas considered to be in frequent and less frequent contact, with the exception of hydration, which was greater for areas of less frequent contact.(ABSTRACT TRUNCATED AT 250 WORDS)

Animals↗

Changes in proteoglycan synthesis of chondrocytes in articular cartilage are associated with the time-dependent changes in their mechanical environment.

Explant loading experiments were conducted to investigate the effect of load duration on proteoglycan synthesis. A compressive load of 0.1 MPa applied for 10 min was found to stimulate proteoglycan synthesis, while the same load applied for 20 h suppressed synthesis. This bimodal response suggests that the cells are responding to different mechanical stimuli as time progresses. A theoretical model has therefore been developed to describe the mechanical environment perceived by cells within soft hydrated tissues (e.g. articular cartilage) while the tissue is being loaded. The cells are modeled, using the biphasic theory, as fluid-solid inclusions embedded in and attached to a biphasic extracellular matrix of distinct material properties. A method of solution is developed which is valid for any axisymmetric loading configuration, provided that the cell radius, a, is small relative to the tissue height, h (i.e. h/a >> 1). A closed-form analytical solution for this inclusion problem is then presented for the confined compression configuration. Results from this model show that the mechanical environment in and around the cells is time dependent and inhomogeneous, and can be significantly influenced by differences in properties between the cell and the extracellular matrix.

Algorithms↗

Cartilage metalloproteases in disuse atrophy.

A canine knee model of disuse atrophy produced by nonrigid fixation (sling) was characterized in respect to variables of proteoglycan size distribution, as well as biomechanical properties versus controls. Using this model, we found, in addition to the accepted dogma attributing changes to reduced protein synthesis by chondrocytes, that there is elevation of proteases and depression of tissue inhibitor of metalloproteases (TIMP) in atrophic knee cartilage. The findings are suggestive of cartilage remodelling reminiscent of bone remodelling in disuse atrophy reported by others. Whether the abnormal changes of protease-TIMP balance in knee cartilage can be retarded prophylactically by concurrent treatment with pentosan polysulfate and insulin like growth factor 1 remains uncertain.

Animals↗

Regional variation in tensile properties and biochemical composition of the human lumbar anulus fibrosus.

STUDY DESIGN: The structure-function relationship of anulus fibrosus of nondegenerate lumbar intervertebral discs was investigated. OBJECTIVES: The tensile properties and biochemical composition of single lamella specimens from human anulus fibrosus and their variations with anatomic region were determined. SUMMARY OF BACKGROUND DATA: Regional differences in composition and ultrastructure suggest differences in tensile properties. METHODS: Single lamella specimens were isolated from the anulus, equilibrated in 0.15 mol/L NaCl and tested in uniaxial tension using a slow strain-rate protocol. Adjacent specimens were used to determine biochemical composition (including hydration, collagen, proteoglycan, and hydroxypyridinium crosslink density). Tensile properties, biochemical composition, and anatomic location were compared. RESULTS: Significant radial and circumferential variations in tensile properties of anulus were detected, with the anterior being stiffer than the posterolateral regions, and the outer being stiffer than the inner regions. CONCLUSIONS: The regional differences in tensile properties may result predominantly from structural rather than compositional variations and may contribute to the clinical frequency of anulus failure in the posterolateral region.

Collagen↗

Compressive mechanical properties of the human anulus fibrosus and their relationship to biochemical composition.

To enhance understanding of the biomechanical role of the intervertebral disc, the compressive properties and biochemical composition of nondegenerate samples of anulus fibrosus were determined as a function of radial position, region, and level. Because of the large swelling propensity of this tissue, a method was developed to test excised specimens while maintaining their in situ geometry and hydration. Using an analysis based on linear biphasic theory, the compressive modulus, hydraulic permeability, and isometric swelling pressure of the anulus fibrosus were determined and correlated with the tissue composition. The findings indicate that the anulus fibrosus is inhomogeneous, with regional and radial variations in both material properties and biochemical composition. The results of this study suggest that both structural and compositional factors may determine the mechanical behavior.

Adult↗

Radial tie fibers influence the tensile properties of the bovine medial meniscus.

Although collagen fibers are arranged predominantly in the circumferential direction in the knee meniscus, there is evidence for radially oriented fibers within human menisci. A bovine medial meniscus model was used to study the hypothesis that radial fibers alter the radial tensile properties of the meniscus. The architecture of the collagen network and tensile properties of the bovine medial meniscus were examined; attention was given to large "radial tie fibers" and their regional variation. Menisci were sectioned serially into slices 400 microns thick. Polarized light microscopy showed that the distribution of radial tie fibers varied greatly among the anterior, central, and posterior regions. These radial tie fibers were larger and more frequent in the posterior region. Radial fibers persisted over many adjacent sections with similar architecture, which led to our hypothesis that they may be arranged in continuous sheets in which the morphology varies by region. Radially oriented specimens for tensile testing were grouped according to the number of radial tie fibers (full, partial, and no fiber) and region (anterior, central, and posterior). Uniaxial tensile testing was performed on a testing machine at a strain rate of 0.00017 sec-1 until failure. The tensile modulus, ultimate tensile stress, and ultimate tensile strain were determined. The presence of radial tie fibers in the specimen had a significant effect on the tensile modulus and ultimate tensile stress. Specimens containing full radial tie fibers were stiffest and failed at the lowest strains; in specimens from the posterior region, the tensile modulus was 392%, the ultimate tensile stress was 314%, and the ultimate tensile strain was 68% that of the specimens with no radial fibers. In no-fiber specimens, the tensile modulus in the posterior region was 225% of the modulus in the anterior region, and the ultimate tensile strain in the posterior region was 68% that of the strain in the anterior region. The abundance of radial tie fibers in the posterior region seems to contribute to the increased stiffness of this region. The preferential stiffening of the posterior region by these radial fibrous sheets may be well suited to the manner in which the bovine medial meniscus functions in load-bearing.

Animals↗

Mechanical properties of canine articular cartilage are significantly altered following transection of the anterior cruciate ligament.

The compressive, tensile, and swelling properties of articular cartilage were studied at two time periods following transection of the anterior cruciate ligament in the knee of greyhound dogs. An experimental protocol was designed to quantify the essential equilibrium and biphasic material properties of cartilage in tension, compression, and shear, as well as the parameters of isometric swelling behavior. All properties were measured at several sites to elicit differences between sites of frequent and less frequent contact. Hydration was determined at each site and was compared with the material properties of cartilage from corresponding sites. There were extensive changes in all compressive, tensile, and swelling properties of cartilage after transection of the anterior cruciate ligament. Twelve weeks after surgery, the intrinsic moduli were reduced significantly in compression (approximately 24% of control values), tension (approximately 64%), and shear (approximately 24%), and the hydraulic permeability was elevated significantly (approximately 48%). Significant increases in hydration (approximately 9%) also were observed, as well as a strong correlation of hydration with hydraulic permeability. The pattern of these changes was not found to differ with site in the joint, but significant differences were observed in the magnitude of change for cartilage from the femoral groove and the femoral condyle. The pattern and extent of changes in the material properties following transection of the anterior cruciate ligament indicate that altered loading of the joint severely compromises the overall mechanical behavior of articular cartilage. The observed loss of matrix stiffness in compression, tension, and shear is associated with increases in the deformation of the solid matrix, a diminished ability to resist swelling, and the increase in hydration observed in this study. The increased swelling and elevated water content were related directly to the increase in hydraulic permeability; this suggests an associated loss of fluid pressurization as the load support mechanism in the degenerated cartilage. Without a successful mechanism for repair, damage to the solid matrix may progress and lead to further degenerative changes in the biochemistry, morphology, and mechanical behavior of articular cartilage.

Animals↗

Mechanical and biochemical changes in the superficial zone of articular cartilage in canine experimental osteoarthritis.

The changes in the tensile mechanical properties and biochemical composition of the superficial zone of articular cartilage were examined in a canine model of early osteoarthritis generated by transection of the anterior cruciate ligament. Sixteen weeks following ligament transection, the tensile stiffness of the articular cartilage was decreased by 44% and the ion-induced stress relaxation of the tissue was increased by 57% compared with the contralateral control. Biochemical analyses indicated that the water content of the experimental tissue was increased by 13%, which was reflected as an apparent 37% decrease in the proteoglycan content and a 36% decrease in the collagen content (expressed per wet weight). The hydroxypyridinium crosslink density was decreased in the experimental tissue by 11%. A significant negative correlation was found between the ion-induced stress relaxation and the hydroxypyridinium crosslink density in both control tissue (R = -0.56) and experimental tissue (R = -0.70). No correlation was noted between the tensile stiffness and the biochemical composition of the tissue. These results suggest that, in the superficial zone of articular cartilage, the structure of the tissue may play a more important role than the composition in the determination of its mechanical properties. A major event observed in the model of early osteoarthritis appears to be the disruption and remodeling of the collagen network in the superficial zone of the articular cartilage.

Animals↗

Centrifugal and biochemical comparison of proteoglycan aggregates from articular cartilage in experimental joint disuse and joint instability.

Two models involving altered joint loading were compared with regard to their effects on the biochemical composition and proteoglycan aggregate structure of articular cartilage. Disuse atrophy was created in greyhound dogs by nonrigid immobilization of the right knee in 90 degrees of flexion, and joint instability was created by transection of the anterior cruciate ligament. Similarities and differences between the two experimental groups at two different time periods were examined to investigate why joint instability induces progressive and irreversible changes to the articular cartilage, whereas joint disuse induces changes that may be reversible when the joint is remobilized. The following studies were performed on the cartilage from all experimental and control groups: (a) compositional analyses to determine water, uronate, and hydroxyproline contents; (b) high performance liquid chromatography for detection of hyaluronan and chondroitin sulfates; and (c) centrifugation analyses of nondissociatively extracted and purified proteoglycans to isolate and quantify the populations of monomers and slow and fast-sedimenting families of aggregates. In general, all cartilage was found to have a decreased ratio of proteoglycan to collagen after 4 weeks of disuse, and this ratio returned to control values at 8 weeks. In contrast, cartilage had an elevated ratio of proteoglycan to collagen as well as increased hydration at 12 weeks after transection of the anterior cruciate ligament. The most striking contrast between the two models was the finding of an approximately 80% decrease in the content of hyaluronan at both time periods after transection of the anterior cruciate ligament, with no evidence of a change after disuse. The results of centrifugation analyses indicated a significant decrease in the quantity of proteoglycan aggregates in both models. However, this decrease was associated primarily with a loss of slow-sedimenting aggregates after disuse and a loss of both slow and fast-sedimenting aggregates after transection of the anterior cruciate ligament. Furthermore, the population of fast-sedimenting aggregates was depleted to a greater extent than that of the slow-sedimenting aggregates. The preservation of fast-sedimenting aggregates as well as hyaluronan after periods of joint disuse but not joint instability suggests a possible mechanism for the reversibility of cartilage changes. Although the proteoglycan aggregates were depleted after disuse atrophy, it is possible that an aggregate-depleted matrix could recover when normal proteoglycan synthesis is resumed. In contrast, although synthesis may be maintained or elevated after transection of the anterior cruciate ligament, the matrix may not be repopulated with aggregates because there is an insufficient amount of hyaluronan.

Analysis of Variance↗