Biomedical subjects

Sherry L Voytik-Harbin

Publications and source records attributed to Sherry L Voytik-Harbin.

3 recordsLinked to original sources

PubMed2004

Local, three-dimensional strain measurements within largely deformed extracellular matrix constructs.

The ability to create extracellular matrix (ECM) constructs that are mechanically and biochemically similar to those found in vivo and to understand how their properties affect cellular responses will drive the next generation of tissue engineering strategies. To date, many mechanisms by which cells biochemically communicate with the ECM are known. However the mechanisms by which mechanical information is transmitted between cells and their ECM remain to be elucidated. "Self-assembled" collagen matrices provide an in vitro-model system to study the mechanical behavior of ECM. To begin to understand how the ECM and the cells interact mechanically, the three-dimensional (3D) mechanical properties of the ECM must be quantified at the micro-(local) level in addition to information measured at the macro-(global) level. Here we describe an incremental digital volume correlation (IDVC) algorithm to quantify large (>0.05) 3D mechanical strains in the microstructure of 3D collagen matrices in response to applied mechanical loads. Strain measurements from the IDVC algorithm rely on 3D confocal images acquired from collagen matrices under applied mechanical loads. The accuracy and the precision of the IDVC algorithm was verified by comparing both image volumes collected in succession when no deformation was applied to the ECM (zero strain) and image volumes to which simulated deformations were applied in both ID and 3D (simulated strains). Results indicate that the IDVC algorithm can accurately and precisely determine the 3D strain state inside largely deformed collagen ECMs. Finally, the usefulness of the algorithm was demonstrated by measuring the microlevel 3D strain response of a collagen ECM loaded in tension.

Anisotropy↗

PubMed2003

Simultaneous mechanical loading and confocal reflection microscopy for three-dimensional microbiomechanical analysis of biomaterials and tissue constructs.

At present, mechanisms by which specific structural and mechanical properties of the three-dimensional extracellular matrix microenvironment influence cell behavior are not known. Lack of such knowledge precludes formulation of engineered scaffolds or tissue constructs that would deliver specific growth-inductive signals required for improved tissue restoration. This article describes a new mechanical loading-imaging technique that allows investigations of structural-mechanical properties of biomaterials as well as the structural-mechanical basis of cell-scaffold interactions at a microscopic level and in three dimensions. The technique is based upon the integration of a modified, miniature mechanical loading instrument with a confocal microscope. Confocal microscopy is conducted in a reflection and/or fluorescence mode for selective visualization of load-induced changes to the scaffold and any resident cells, while maintaining each specimen in a "live," fully hydrated state. This innovative technique offers several advantages over current biomechanics methodologies, including simultaneous visualization of scaffold and/or cell microstructure in three dimensions during mechanical loading; quantification of macroscopic mechanical parameters including true stress and strain; and the ability to perform multiple analyses on the same specimen. This technique was used to determine the structural-mechanical properties of three very different biological materials: a reconstituted collagen matrix, a tissue-derived biomaterial, and a tissue construct representing cells and matrix.

3T3 Cells↗

PubMed2002

Tensile mechanical properties of three-dimensional type I collagen extracellular matrices with varied microstructure.

The importance and priority of specific micro-structural and mechanical design parameters must be established to effectively engineer scaffolds (biomaterials) that mimic the extracellular matrix (ECM) environment of cells and have clinical applications as tissue substitutes. In this study, three-dimensional (3-D) matrices were prepared from type I collagen, the predominant compositional and structural component of connective tissue ECMs, and structural-mechanical relationships were studied. Polymerization conditions, including collagen concentration (0.3-3 mg/mL) and pH (6-9), were varied to obtain matrices of collagen fibrils with different microstructures. Confocal reflection microscopy was used to assess specific micro-structural features (e.g., diameter and length) and organization of component fibrils in 3-D. Microstructural analyses revealed that changes in collagen concentration affected fibril density while maintaining a relatively constant fibril diameter. On the other hand, both fibril length and diameter were affected by the pH of the polymerization reaction. Mechanically, all matrices exhibited a similar stress-strain curve with identifiable "toe," "linear," and "failure" regions. However the linear modulus and failure stress increased with collagen concentration and were correlated with an increase in fibril density. Additionally, both the linear modulus and failure stress showed an increase with pH, which was related to an increasedfibril length and a decreasedfibril diameter. The tensile mechanical properties of the collagen matrices also showed strain rate dependence. Such fundamental information regarding the 3-D microstructural-mechanical properties of the ECM and its component molecules are important to our overall understanding of cell-ECM interactions (e.g., mechanotransduction) and the development of novel strategies for tissue repair and replacement.

Animals↗