Biomedical subjects

Roger St C Smart

Publications and source records attributed to Roger St C Smart.

7 recordsLinked to original sources

PubMed2006

A simplified method for estimation of jarosite and acid-forming sulfates in acid mine wastes.

In acid base accounting (ABA) estimates of acid mine wastes, the acid potential (AP) estimate can be improved by using the net carbonate value (NCV) reactive sulfide S method rather than total S assay methods but this does not give recovery of potentially acid producing ferrous and ferric sulfates present in many wastes. For more accurate estimation of AP, an effective, site-specific method to quantify acid sulfate salts, such as jarosite and melanterite, in waste rocks has been developed and tested on synthetic and real wastes. The SPOCAS (acid sulfate soils) methods have been modified to an effective, rapid method to speciate sulfate forms in different synthetic waste samples. A three-step sequential extraction procedure has been established. These steps are: (1) argon-purged water extraction (3 min) to extract soluble Fe(II) salts (particularly melanterite), epsomite and gypsum (<10 wt.%), (2) roasting at 550 degrees C (1 h) to remove sulfur from pyrite and other reactive sulfides, (3) HCl extraction (4 M, 30 min) for determination of jarosites. Products (solid and aqueous) have been characterized at each step including the jarosite decomposition process in Step 2 where temperature control is critical to avoid S loss. The sequential extraction procedure was used to quantitatively determine melanterite, epsomite, gypsum, pyrite and jarosite concentrations in a synthetic waste sample containing these mineral phases at 5 wt.% in quartz, and also tested using a tailings waste sample to quantitatively determine epsomite, gypsum and jarosite contents. The method is applicable to most waste samples including those with non-pyrite sulfides but for samples containing significant amounts of sulfur (>1 wt.% S) as copper sulfides, the second step of roasting needs to be excluded from the procedure with an increased time of 4 M HCl extraction to 16 h for jarosite determination.

Journal Article↗

PubMed2006

Thin calcium phosphate coatings on titanium by electrochemical deposition in modified simulated body fluid.

Adherent and optically semitransparent thin calcium phosphate (CaP) films were electrochemically deposited on titanium substrates in a modified simulated body fluid at 37 degrees C. Coatings deposited by using periodic pulsed potentials showed better adhesion and better mechanical properties than coatings deposited with use of a constant potential. Scanning electron microscopy was used to study the morphology of the coatings. The coatings displayed a polydispersed porous structure with pores in the range of a few nanometers to 1 mum. Furthermore, X-ray diffractometry and the O(1s) satellite peaks in X-ray photoelectron spectroscopy indicated that the coatings possessed a similar surface chemistry to that of natural bone minerals. These results were confirmed by inductively coupled plasma optical emission spectrometry, which yielded a Ca:P ratio of 1.65, close to that of hydroxyapatite. Contact mode atomic force microscopy (AFM) showed the average thickness of the coatings was in the order of 200 nm. Root-mean-square (RMS) roughness values, also derived by AFM, were shown to be much higher on the titanium-CaP surfaces in comparison with untreated titanium substrates, with RMS values of about 300 and 110 nm, respectively. Cell culture experiments showed that the CaP surfaces are nontoxic to MG63 osteoblastic cells in vitro and were able to support cell growth for up to 4 days, outperforming the untreated titanium surface in a direct comparison. These easily prepared coatings show promise for hard-tissue biomaterials.

Adhesiveness↗

PubMed2006

Adsorption of bisphosphonate onto hydroxyapatite using a novel co-precipitation technique for bone growth enhancement.

Premature bone resorption and remodeling by osteoclasts can limit the longevity of implant fixation and recovery time. Orally administered bisphosphonates (BPs) have been used to inhibit osteoclast action at the implant/bone interface. Ideally, these should be delivered at the interface with the osteoblast-active hydroxyapatite (HA) for maximum effect. This investigation introduces a novel BP loading technique to achieve improved BP release from a simulated body fluid-grown HA (SBF-HA) with the aim of improving implant fixation. A solution co-precipitation technique incorporates the BP (pamidronate) into a thin SBF-HA coating. Surface analysis, using X-ray photoelectron spectroscopy (XPS), of the resultant coating was employed to confirm the presence of the adsorbed BP on the surface of SBF-HA. XPS analysis was also used to determine the optimal adsorption process. Osteoclast cell culture experiments confirmed the biological effectiveness of BP adsorption and proved that the pamidronate was biologically active, causing both decreased osteoclast numbers and decreased resorption.

Adsorption↗

PubMed2005

Direct measurement of interactions between adsorbed vitronectin layers: the influence of ionic strength and pH.

Vitronectin (Vn) is an adhesive protein in the plasma serum and plays an important role in cell attachment, spreading, and proliferation. The interactions between protein bovine vitronectin layers adsorbed onto a silica probe and a mica surface have been investigated with the use of atomic force microscopy (AFM). Adsorption of vitronectin was confirmed by XPS surface analysis. The force-separation curves and pull-off forces were measured as a function of ionic strength and solution pH. The pull-off force (adhesion force) decreased as the salt concentration increased, which suggests that some binding domains of this protein may associate with the ionic species and reduce its binding ability. Discrete jumps, or discontinuities, in the separation force curve were observed to extend to a maximum of 300 nm, evidence that the protein molecules bridge between the surfaces. As a function of pH, the adhesion force on separation of the protein-coated surfaces showed a maximum at pH 5 (i.e.p. of vitronectin), decreasing in magnitude at lower and higher pH values. At pH 5, the approaching curves illustrated a jump-in force; whereas for pH values away from 5, the approaching force curves were repulsive. Correlation of the interaction forces with Vn conformational changes in different pH environments, directly visualized with the use of AFM imaging, was developed. In its i.e.p. region, the Vn molecular conformation appeared to be dense and compact. Significantly, at wounds/injured sites the pH is low (approximately 5) which this study discovered to facilitate adsorption and formation of vitronectin aggregates, known to trigger their subsequent biological functions.

Adhesiveness↗

PubMed2004

Vitronectin adsorption on surfaces visualized by tapping mode atomic force microscopy.

Vitronectin (Vn) is an abundant glycoprotein present in plasma and the extracellular matrix of most tissue and is an important medium required for bone cells to attach and spread on biomaterial surfaces. Hence, Vn adsorption is an initial and key step in implantation. In this study, adsorption of Vn molecules on mica and oxidized titanium substrates in Milli-Q water (pH 5.6) and in simulated body fluid (SBF, pH 7.4) has been investigated using tapping mode atomic force microscopy. Conformation of the adsorbed proteins was determined from the images. The effect of adsorption time was investigated on mica surfaces. The protein first attaches to the surface, then immediately spreads out with different lateral dimensions of adsorbed protein and becomes aggregated. After 15 min of adsorption, globular Vn molecules form clusters of aggregates in extended chains on the mica surface. Globular Vn molecules appear flatter (i.e., oblate ellipsoids) and coalesce on the ridges of the uneven oxidized titanium surface. From cross-sectional analyses of the Vn images, it was found that the contact areas of Vn molecules associated with Ti surfaces are larger than those with mica surfaces. This suggests that the different surface properties of substrates contribute to this different conformation of adsorbed Vn molecules. The larger contact areas of Vn associated with Ti substrates indicates higher affinity for the biomaterial oxidized titanium surface than for mica. In SBF, Vn interacted weakly with the mica surfaces and Vn molecules were easily desorbed during the imaging process. On oxidized titanium substrates, after 3 h of incubation time in Vn-SBF solution, images can be obtained showing adsorbed Vn aggregates on the oxidized titanium surface. In this case, the protein colloids are strongly adherent, with increased lateral dimensions compared with the adsorption on mica.

Adsorption↗

PubMed2003

Influence of aluminum doping on titania pigment structural and dispersion properties.

The influence of aluminum concentration on the structural properties and rheological behavior of aqueous suspensions of aluminum-doped titania pigment from the chloride process was investigated. The variation in rheological properties correlates with the change in the pigment surface properties, determined from electrophoresis measurements and atomic surface concentrations. Pigment suspensions exhibited a maximum yield stress and viscosity at or near the isoelectric point (iep). The pH of the maximum yield value of the pigment suspension increases with increasing aluminum hydroxyl group density at the particle surface. For pigments with a high aluminum surface concentration, at pH values where the magnitude of the zeta potential was high, a low-viscosity, dispersed suspension was obtained. The pigment with the lowest aluminum concentration, however, retained high yield stresses over a large pH range even when the zeta potential was of considerable magnitude. Pigment particle interactions are chiefly dictated by van der Waals forces and electrostatic repulsive forces, likely to be influenced by heteroaggregation. The aggregate strength would therefore depend upon the proportion and distribution of aluminum and titanium surface groups of the heterogeneous pigment, which will influence both the Hamaker constant and the degree of heteroaggregation. Overall, very small additions to the total aluminum concentration translate to significant aluminum surface concentration disparities and subsequently to large particle interaction differences.

Aluminum↗

PubMed2002

Kinetics of adsorption of high molecular weight anionic polyacrylamide onto kaolinite: the flocculation process.

The adsorption kinetics of anionic polyacrylamide flocculant onto kaolinite clay are examined as a function of flocculant dosage and pH. Special attention has been given to the flocculation effect during the adsorption process and the resulting inhibition of further adsorption. At pH 8.5 the adsorption capacity of anionic polyacrylamide on kaolinite is low while at pH 4.5, the adsorption capacity increases. Flocculant adsorption has been shown to be related to the amount of available surface area, pH, flocculant dosage, and the resulting floc strength, which controls the rate of new surface area exposure and hence the continuation of further adsorption. At both pH 4.5 and pH 8.5, complete adsorption is achieved at low flocculant dosages and adsorption equilibrium is achieved at high flocculant dosages after 1 day. In contrast, at intermediate flocculant dosages adsorption equilibrium is not reached over a 7-day period, due to a continuously increasing surface area.

Journal Article↗