Search PubMed⌕ Search

Biomedical subjects

R Huiskes

Publications and source records attributed to R Huiskes.

At least 37 records · Page 2Linked to original sources
PubMed2002

Finite element and experimental models of cemented hip joint reconstructions can produce similar bone and cement strains in pre-clinical tests.

Finite element (FE) models could be used for pre-clinical testing of cemented hip replacement implants against the damage accumulation failure scenario. To accurately predict mechanical failure, the models should accurately predict stresses and strains. This should be the case for various implants. In the current study, two FE models of composite hip reconstructions with two different implants were validated relative to experimental bone and cement strains. The objective was an overall agreement within 10% between experimental and FE strains. Two stem types with different clinical results were analyzed: the Lubinus SPII and the Mueller Curved with loosening rates of 4% and 16% after 10 yr, respectively (Prognosis of total hip replacement. 63rd Annual Meeting of the American Academy of orthopaedic surgeons, Atlanta, USA). For both implant types, six stems were implanted in composite femurs. All specimens were subjected to bending. The Mueller Curved specimens were additionally subjected to torsion. Bone strains were recorded at 10 locations on the cortex and cement strains at three locations within the cement mantle. An FE model was built for both stem types and the experiments were simulated. Bone and cement strains were calculated at the experimental gauge locations. Most FE bone strains corresponded to the mean experimental strains within two standard deviations; most FE cement strains within one standard deviation. Linear regression between the FE and mean experimental strains produced slopes between 0.82 and 1.03, and R(2) values above 0.98. Particularly for the Mueller Curved, agreement improved considerably when FE strains were compared to the strains from the experimental specimen used to build the FE model. The objective of overall agreement within 10% was achieved, indicating that both FE models were successfully validated. This prerequisite for accurately predicting long-term failure has been satisfied.

Bone Cements↗
PubMed2002

How morphology predicts mechanical properties of trabecular structures depends on intra-specimen trabecular thickness variations.

Two observations underlie this work. First, that the architecture of trabecular bone can accurately predict the mechanical stiffness characteristics of bone specimens when considering the combination of volume fraction and fabric, which is a measure of architectural anisotropy. Second, that the same morphological measures could not accurately predict the mechanical properties of porous structures in general. We hypothesize that this discrepancy can be explained by the special nature of trabecular bone as a structure in remodeling equilibrium relative to the external loads. We tested this hypothesis using a generic model of trabecular bone. Five series of 153 different architectures were created with this model. Each architecture was subjected to morphological analysis, and four different fabric measures were calculated to evaluate their effectiveness in characterizing the architecture. Relationships were determined relating morphology to the elastic constants. The quality of these relationships was tested by correlating the predicted elastic constants with those determined from finite element analysis. We found that the four fabric measures used could estimate the mechanical properties almost equally well. So the suggestion that fabric measures based on trabecular bone volume better represent the architecture than mean intercept length could not be affirmed. We conclude that for structures with equally sized elliptical voids the mechanical properties can be predicted well only if trabecular thickness variations within each structure are limited. These structures closely resemble previously developed models of trabecular bone. Furthermore, they are stiff in the principal fabric direction, hence, according to Cowin (J. Biomech. Eng. (108) (1986) 83), they are in remodeling equilibrium. These structures are also stiff over a large range of loading orientations, hence, are relatively insensitive to deviations in direction of loading.

Bone and Bones↗
PubMed2002

Cancellous bone mechanical properties from normals and patients with hip fractures differ on the structure level, not on the bone hard tissue level.

Osteoporosis is currently defined in terms of low bone mass. However, the source of fragility leading to fracture has not been adequately described. In particular, the contributions of bone tissue properties and architecture to the risk or incidence of fracture are poorly understood. In an earlier experimental study, it was found that the architectural anisotropy of cancellous bone from the femoral heads of fracture patients was significantly increased compared with age- and density-matched control material (Ciarelli et al., J Bone Miner Res 15:32-40; 2000). Using a combination of compression testing and micro-finite element analysis on a subset of cancellous bone specimens from that study, we calculated the hard tissue mechanical properties and the apparent (macroscopic) mechanical properties. The tissue modulus was 10.0 GPa (SD 2.2) for the control group and 10.8 GPa (SD 3.3) for the fracture group (not significant). There were no differences in either the apparent yield strains, percentages of highly strained tissue, or the relationship between apparent yield stress and apparent elastic modulus. Hence, a difference in the tissue yield properties is unlikely. At the apparent level, the fracture group had a significantly decreased transverse stiffness, resulting in increased mechanical anisotropy. These changes suggest that bone in the fracture group was "overadapted" to the primary load axis, at the cost of fragility in the transverse direction. We conclude that individuals with a history of osteoporotic fractures do not have weaker bone tissue. Architectural and mechanical anisotropy alone renders their bone weaker in the nonprimary loading direction.

Aged↗
PubMed2002

The influence of microcomputed tomography threshold variations on the assessment of structural and mechanical trabecular bone properties.

In this study, we investigate how morphological parameters and mechanical properties derived from microcomputed tomography (microCT) are affected by small errors in threshold value when variable bone structures and different bone volume fractions are involved. For this purpose, biopsies of vertebrae of 6-, 23-, and 230-week-old female pigs were scanned using microCT. For each specimen, five threshold values were determined within the range of thresholds that an observer could select realistically, in steps of 0.5%. The scans were converted to microfinite-element (microFE) models, used to determine the elastic moduli. A variation of 0.5% in threshold resulted in a 5% difference in bone volume fraction and 9% difference in maximal stiffness for bone cubes with a volume fraction of <0.15. When the volume fraction was >0.2, these differences were only 2% and 3%, respectively. For all bone cubes, the differences for trabecular thickness and bone surface density were <3%. The effects on morphological anisotropy and trabecular number were negligible for threshold variations of 0.5%. These findings suggest that threshold selection is important for the accurate determination of volume fraction and mechanical properties, especially for low bone volume fractions; the architectural directionality is less sensitive to changes in threshold.

Animals↗
PubMed2002

Bone grafting of cryosurgically treated bone defects: experiments in goats.

It is hypothesized that cryosurgically treated bone defects are inappropriate host sites for cancellous bone grafting. The influence of autologous cancellous bone grafting on the healing of cryosurgically treated gap defects of long bones was investigated. A unilateral in vivo experiment was done to study bone strength and graft incorporation in the goat. The lining of a cylindrical defect of the femoral diaphysis was treated with a closed liquid nitrogen cryoprobe in 62 goats. Thirty-one animals received an impacted, morselized, cancellous bone graft harvested from the sternum. The other 31 animals served as controls. At 0, 4, 7, 10, 13, 16, and 26 weeks animals were euthanized and the femurs were evaluated for torsional strength, computed tomography, and histologic assessment. Specimens with a bone graft showed no significant increase in torsional strength with time compared to the controls. In all goats euthanized at 10 weeks or later, the graft was resorbed. The amount of bone apposition at the site of the cryosurgical lesion and the time at which the defect was bridged were similar in both groups. Autologous cancellous bone grafting does not accelerate healing of cryosurgically treated, stable, diaphyseal defects in the goat.

Animals↗
PubMed2002

Effects of metal-inlay thickness in polyethylene cups with metal-on-metal bearings.

A way to prevent polyethylene wear in total hip replacements is to use metal-on-metal bearings. The cup design of these bearings may be a metal inlay in a polyethylene cup. However, these metal inlays are relatively thin and may deform on loading. The purpose of the current study was to determine whether these potential problems become actual for a realistic range of metal-inlay components having a thickness greater than 1 mm. For this purpose, the effects of thickness variation of a metal inlay in an ultrahigh molecular weight polyethylene cup were determined using three-dimensional finite element techniques. The results showed no indications for jamming of the bearing assuming a realistic inlay thickness (3-5 mm), even with a small clearance (25 microm). The metal inlay acted rigidly beyond a thickness of approximately 5 mm. Metal inlays thinner than 1.5 mm led to a considerable increase in contact area and a reduction in contact peak stress, which may be beneficial for the bearing performance. Currently, these thin liners have too many unknown characteristics and therefore the current authors recommend using rigid metal liners that have a thickness greater than 5 mm.

Biomechanical Phenomena↗
PubMed2002

A description of the motion of the navicular bone during in vitro vertical loading of the equine forelimb.

Motion of the navicular bone might play a role in the development of navicular disease in horses but is difficult to asses. In the present study, 3-dimensional motion of this bone was determined using roentgen stereophotogrammetric analysis. Tantalum pellets were inserted, in vitro, in the bones of 6 forelimbs of mature Shetland ponies and kinematics were measured during vertical loading up to 2 kN. The motions of the navicular bone and coffin joint were limited to flexion/extension, there were no substantial out-of-plane motions. There was only little flexion between the navicular bone and the coffin bone, which was correlated (r = 0.66) with coffin joint flexion. There was substantial flexion between the navicular bone and the short pastern, which was highly correlated with coffin joint flexion (r = 0.97). We conclude that the navicular bone, generally, follows the coffin bone during coffin joint flexion, although there are small but consistent motions between the navicular bone and the coffin bone. These motions might play a role in the development of navicular disease in horses.

Animals↗
PubMed2001

Osteoporosis changes the amount of vertebral trabecular bone at risk of fracture but not the vertebral load distribution.

STUDY DESIGN: A finite-element study to investigate the amount of trabecular bone at risk of fracture and the distribution of load between trabecular core and cortical shell, for healthy, osteopenic, and osteoporotic vertebrae. OBJECTIVES: To determine differences between healthy, osteopenic, and osteoporotic vertebrae with regard to the risk of fracture and the load distribution. SUMMARY OF BACKGROUND DATA: The literature contains no reports on the effects of osteopenia and osteoporosis on load distribution in vertebral bodies, nor any reports on the amount of trabecular bone at risk of fracture. METHODS: Computed tomography data of vertebral bodies were used to construct patient-specific finite-element models. These models were then used in finite-element analyses to determine the physiologic stresses and strains in the vertebrae. RESULTS: For all three classes of vertebrae the contribution of the trabecular core to the total load transfer decreased from about 70% near the endplates to about 50% in the midtransverse region. The amount of trabecular bone that is at risk of fracture was about 1% for healthy vertebrae, about 3% for osteopenic vertebrae, and about 16% for osteoporotic vertebrae. CONCLUSIONS: Our finite-element models indicated that neither osteopenia nor osteoporosis had any effect on the contribution of the trabecular core to the total load placed on the vertebra. The trabecular core carried about half the load. Our finite-element models indicated that osteoporosis had a significant effect on the amount of trabecular bone at risk of fracture, which increased from about 1% in healthy vertebrae to about 16% for osteoporotic vertebrae.

Adult↗
PubMed2001

Time-dependent mechanical properties of HA/TCP particles in relation to morsellized bone grafts for use in impaction grafting.

In reconstructive surgery human bone defects are sometimes filled with the use of the impaction bone grafting technique. Currently different types of biomaterial particles are being developed as bone-substitute materials. Before these biomaterials can be applied their mechanical and biological behavior should be characterized. In this study the time-dependent mechanical behavior of biomaterial particles with different tri-calcium-phosphate/hydroxy-apatite (TCP:HA) ratios, particle sizes, and porosities is determined and compared to the behavior of human bone grafts, the latter being the standard material currently used to augment bone defects. The mechanical properties were assessed with the use of dynamic confined compression creep tests with a loading and unloading phase. Different graft material groups were tested, consisting of 100% human bone grafts, 100% biomaterial particles, and 50:50 weight mixtures of human grafts and biomaterial particles. No damage to the particles was observed by the impaction in the test chamber or by the dynamic load. Relative to the human graft material, the biomaterial particles hardly deformed under loading, were much stiffer, and showed almost no viscoelastic behavior. The mixtures showed intermediate results. Particle size and porosity influenced the behavior of the biomaterial particles. TCP:HA ratio did not have a great effect. The conclusion is that the application of these particles should be done with great care, as their mechanical behavior is drastically different than that of the human graft material. Mixing it with human bone grafts gave the material some biphasic, viscoelastic behavior that may be important for its biological response.

Biocompatible Materials↗
PubMed2001

Hip-joint and abductor-muscle forces adequately represent in vivo loading of a cemented total hip reconstruction.

Using finite element analyses, we investigated which muscle groups acting around the hip-joint most prominently affected the load distributions in cemented total hip reconstructions with a bonded and debonded femoral stem. The purpose was to determine which muscle groups should be included in pre-clinical tests, predicting bone adaptation and mechanical failure of cemented reconstructions, ensuring an adequate representation of in vivo loading of the reconstruction. Loads were applied as occurring during heel-strike, mid-stance and push-off phases of gait. The stress/strain distributions within the reconstruction, produced by the hip-joint contact force, were compared to ones produced after sequentially including the abductors, the iliotibial tract and the adductors and vastii. Inclusion of the abductors had the most pronounced effect. They neutralized lateral bending of the reconstruction at heel-strike and increased medial bending at mid-stance and push-off. Bone strains and stem stresses were changed accordingly. Peak tensile cement stresses were reduced during all gait phases by amounts up to 50% around a bonded stem and 11% around a debonded one. Additional inclusion of the iliotibial tract, the adductors and the vastii produced relatively small effects during all gait phases. Their most prominent effect was a slight reduction of bone strains at the level of the stem tip during heel-strike. These results suggest that a loading configuration including the hip-joint contact force and the abductor forces can adequately reproduce in vivo loading of cemented total hip reconstructions in pre-clinical tests.

Biomechanical Phenomena↗
PubMed2001

Introduction and evaluation of a gray-value voxel conversion technique.

In micro finite element analyses (microFEA) of cancellous bone, the 3D-imaging data that the FEA-models are based on, contain a range of gray-values. In the construction of the eventual FEA-model, these gray-values are commonly thresholded. Although thresholding is successful at small voxel sizes, at larger voxel sizes there is substantial loss of trabecular connectivity. We propose a new method: the gray-value method, where the microFEA-models use the information within the 3D-imaging data directly, without prior thresholding. Our question was twofold. First, how does the gray-value method compare to both plain and mass-compensated thresholding? Second, what is the effect of element size on the results obtained with the gray-value method? We used nine microCT-scans of human vertebral cancellous bone. These were degraded to represent different resolutions, and converted into microFEA-models using plain thresholding, mass-compensated thresholding, and the gray-value method. The apparent elastic moduli of the specimens were determined using microFEA. The different methods were compared on the basis of the apparent elastic moduli, compared to those calculated for a 28 microm reference model. The results showed that the gray-value method greatly improves the results relative to other methods. The gray-value method gives accurate predictions of the apparent elastic moduli, for voxel sizes up to one trabecular thickness (Tb.Th.). For voxel sizes greater than one Tb.Th. the accuracy, although still better than for both thresholding methods, becomes increasingly worse.

Biomechanical Phenomena↗
PubMed2001

Stress distribution changes in bovine vertebrae just below the endplate after sustained loading.

OBJECTIVE: To describe the pattern of stress distribution in the vertebral body just behind the endplate, and to document its changes due to sustained loading. METHODS: Twelve fresh bovine coccygeal motion segments were dissected and tested. Each specimen was axially loaded with a sustained compressive force of 50% of its estimated compressive strength. Before loading, after 1.5 h and after 3 h of loading, the distribution of the axial pressure under the bottom vertebra (i.e., just below its top endplate) was recorded at three force levels (25%, 37.5% and 50% of the estimated compressive strength), using pressure-sensitive film. RESULTS: Stress distribution over the endplate was found to be fairly uniform. At low compression forces, the stress was the highest centrally. With increased compression and after sustained compression the uniformity improved through a significant redistribution of stress to the periphery. No stress peaks were found to occur after sustained loading. CONCLUSION: Stress peaks after sustained loading cannot explain the occurrence of endplate fractures in sustained cyclic compression in non-degenerated discs. Competing explanations, such as creep, and fatigue failure, would appear more likely candidates. RELEVANCE: It has been hypothesised that compression induced fractures of the lumbar vertebral endplate constitute an important etiological factor for low back pain. Competing theories exist on the fracture mechanism in sustained loading and these would have different implications with respect to prevention. The present study evaluated one of these theories.

Analysis of Variance↗
PubMed2001

Increase in bone volume fraction precedes architectural adaptation in growing bone.

In mature trabecular bone, both density and trabecular orientation are adapted to external mechanical loads. Few quantitative data are available on the development of architecture and mechanical adaptation in juvenile trabecular bone. We studied the hypothesis that a time lag occurs between the adaptation of trabecular density and the adaptation of trabecular architecture during development. To investigate this hypothesis we used ten female pigs at 6, 23, 56, 104, and 230 weeks of age. Three-dimensional morphological and mechanical parameters of trabecular bone samples from the vertebra and proximal tibia were studied using microcomputed tomography and micro-finite element analysis. Both bone volume fraction and stiffness increased rapidly in the initial growth phase (from 6 weeks on), whereas the morphological anisotropy started increasing only after 23 weeks of age. In addition, the anisotropy reached its highest value much later in the development than did bone volume fraction. Hence, the alignment of trabeculae was still progressing at the time of peak bone mass. Therefore, our hypothesis was supported by the time lag between the increase in trabecular density and the adaptation of the trabecular architecture. The rapid increase of bone volume fraction in the initial growth phase can be explained by the enormous weight increase of the pigs. The trabeculae aligned at later stages when the increase in weight, and thus the loading, was slowed considerably compared with the early growth stage. Hence, the trabecular architecture was more efficient in later years. We conclude that density is adapted to external load from the early phase of growth, whereas the trabecular architecture is adapted later in the development.

Animals↗
PubMed2001

Load transfer and stress shielding of the hydroxyapatite-ABG hip: a study of stem length and proximal fixation.

We questioned whether the excellent clinical results reported for the hydroxyapatite-coated ABG hip are consistent with results of preclinical computer simulation methods for the prediction of strain-adaptive bone remodeling patterns around implants. We also investigated whether a further improvement of the results can be expected if complete proximal load transfer is enforced by reducing stem length to the metaphyseal area only. Resorption patterns predicted were in good agreement with radiographic clinical findings. Mechanical failure of the bone-implant interface was judged based on a Hoffman interface stress criterion, which was low. Reducing stem length hardly increased interface failure probability, but it did not reduce stress shielding, either. From a mechanical point of view, reducing stem length to the metaphyseal area only is not advantageous.

Arthroplasty, Replacement, Hip↗
PubMed2001

The prospects of estimating trabecular bone tissue properties from the combination of ultrasound, dual-energy X-ray absorptiometry, microcomputed tomography, and microfinite element analysis.

Osteoporosis commonly is assessed by bone quantity, using bone mineral density (BMD) measurements from dual-energy X-ray absorptiometry (DXA). However, such a measure gives neither information about the integrity of the trabecular architecture nor about the mechanical properties of the constituting trabeculae. We investigated the feasibility of deriving the elastic modulus of the trabeculae (the tissue modulus) from computer simulation of mechanical testing by microfinite element analysis (muFEA) in combination with measurements of ultrasound speed of sound (SOS) and BMD measurements. This approach was tested on 15 postmortem bovine bone cubes. The apparent elastic modulus of the specimens was estimated from SOS measurements in combination with BMD. Then the trabecular morphology was reconstructed using microcomputed tomography (muCT). From the reconstruction a mesh for muFEA was derived, used to simulate mechanical testing. The tissue modulus was found by correlating the apparent moduli of the specimens as assessed by ultrasound with the ones as determined with muFEA. A mean tissue modulus of 4.5 GPa (SD, 0.69) was found. When adjusting the muFEA-determined elastic moduli of the entire specimens with their calculated tissue modulus, an overall correlation of R2 = 96% with ultrasound-predicted values was obtained. We conclude that the apparent elastic stiffness characteristics as determined from ultrasound correlate linearly with those from muFEA. From both methods in combination, the elastic stiffness of the mineralized tissue can be determined as an estimator for mechanical tissue quality. This method can already be used for biopsy specimens, and potentially could be applicable in vivo as well, when clinical CT or magnetic resonance imaging (MRI) tools with adequate resolution reach the market. In this way, mechanical bone quality could be estimated more accurately in clinical practice.

Absorptiometry, Photon↗
PubMed2000

Effects of mechanical forces on maintenance and adaptation of form in trabecular bone.

The architecture of trabecular bone, the porous bone found in the spine and at articulating joints, provides the requirements for optimal load transfer, by pairing suitable strength and stiffness to minimal weight according to rules of mathematical design. But, as it is unlikely that the architecture is fully pre-programmed in the genes, how are the bone cells informed about these rules, which so obviously dictate architecture? A relationship exists between bone architecture and mechanical usage--while strenuous exercise increases bone mass, disuse, as in microgravity and inactivity, reduces it. Bone resorption cells (osteoclasts) and bone formation cells (osteoblasts) normally balance bone mass in a coupled homeostatic process of remodelling, which renews some 25% of trabecular bone volume per year. Here we present a computational model of the metabolic process in bone that confirms that cell coupling is governed by feedback from mechanical load transfer. This model can explain the emergence and maintenance of trabecular architecture as an optimal mechanical structure, as well as its adaptation to alternative external loads.

Adaptation, Physiological↗
PubMed2000

Creep properties of three low temperature-curing bone cements: a preclinical assessment.

The mechanical characteristics of new bone cements should be assessed before these cements are released on the orthopedic market in great quantities. In this study, we present the deformational response of 3 relatively new, low-curing temperature bone cements (Cemex RX, Cemex System, and Cemex Isoplastic) to a dynamic compressive force in comparison to Simplex P bone cement. For this purpose, dynamic compressive creep tests were performed on cylindrical shaped specimens at a maximal load level of 20 MPa for a period of 250,000 cycles. The results showed that Cemex System and Cemex RX produced creep rates that were higher (20% and 30%, respectively) as compared to Simplex P bone cement. The creep behavior of Cemex Isoplastic was very similar to that of Simplex P. It was concluded that although Cemex RX and Cemex System produced higher creep rates than Simplex P, these differences were not considered excessive. Hence, although other tests are required to assess the safety and efficacy of these new cements, the dynamic creep properties under compression can be considered adequate for clinical use.

Biocompatible Materials↗