Latanoprost (PhXA41, Xalatan) and isopropyl unoprostone (UF-021, unoprostone, Rescula) two new prostanoid derivatives, have been shown to reduce intraocular pressure (IOP) significantly in patients with glaucoma or ocular hypertension. This study was designed to compare the ocular hypotensive effects of latanoprost and unoprostone in cynomologus monkeys with glaucoma and characterizes the prostanoid's mechanisms of action in normal cynomolgus monkey eyes. Intraocular pressure was measured daily at 0, 0.5, and 1 hour and hourly for 5 additional hours during 1 baseline day, 1 vehicle-treated day, and 5 days of therapy with either 0.005% latanoprost or 0.12% unoprostone applied twice daily, at 9:30 AM and 3:30 PM, to the glaucomatous eye of eight monkeys with unilateral laser-induced glaucoma. Outflow facility was measured in six normal monkeys 3 hours prior to dosing and 1 hour after unilateral dosing with either drug. Aqueous humor flow rates were measured in six normal monkeys hourly for 4 hours on 1 baseline day and on 1 treatment day beginning 1 hour after administration of either drug to one eye. Intraocular pressure was significantly (P < 0.005) reduced after the first application for 4 hours with latanoprost and for 2 hours with unoprostone, up to 5.4 +/- 0.8 mm Hg (mean +/- SEM) (latanoprost) and 3.8 +/- 0.5 mm Hg (unoprostone). Intraocular pressure was significantly (P < 0.005) reduced for at least 18 hours following each PM dose of latanoprost. Intraocular pressure was not reduced (P > .05) 18 hours after each PM dose of unoprostone. An enhancement of the ocular hypotensive effect was observed from day 1 to day 5 with repeated dosing of either drug. Latanoprost produced a greater magnitude of IOP reduction for a longer duration of time than unoprostone after each application. Neither drug altered outflow facility or aqueous humor flow rates. Latanoprost and unoprostone appear to reduce IOP in monkeys by enhancing uveoscleral outflow. Latanoprost appears to be more efficacious and potent than unoprostone in reducing IOP in glaucomatous monkey eyes.

Administration, Topical↗

PubMedDate not supplied

NY-ESO-1 may be a potential target for lung cancer immunotherapy.

PURPOSE: To evaluate the frequency of NY-ESO-1 expression in cultured lung cancer cells and to determine if this cancer-testis antigen can be presented for recognition by an HLA-restricted cytolytic T-cell clone specific for NY-ESO-1. METHODS AND RESULTS: Reverse transcriptase and polymerase chain reaction amplification techniques were utilized to screen a panel of lung and esophageal cancer cell lines for expression of NY-ESO-1 encoding a recently identified cancer-testis antigen. NY-ESO-1 expression was detected in 11 of 16 small cell lung cancer lines, three of seven non-small cell lung cancer lines, and zero of 12 esophageal cancer lines. 5-Aza-2' -deoxycytidine induced expression of NY-ESO-1 in lung cancer cells. Expression of HLA-A31 by plasmid transfection or retroviral transduction enabled recognition of lung cancer cells by an HLA-A31-restricted cytotoxic T lymphocyte clone specific for NY-ESO-1. CONCLUSIONS: NY-ESO-1 expression may be analogous to MAGE gene expression in lung cancer lines in terms of frequency and mechanism of transcriptional regulation. Furthermore, NY-ESO-1 can be presented on lung cancer cells for recognition by HLA-restricted cytotoxic T lymphocytes. Further investigation is warranted to determine if NY-ESO-1 can be exploited for the immunotherapy for lung cancer.

Antigens, Neoplasm↗

PubMedDate not supplied

An in vivo experiment to test composite resin wear using the Latin-Square analysis.

The Michigan Computer Graphics Coordinate Measurement System was used to measure the wear of three composite resins and an amalgam alloy control. The validity of the Latin Square experimental design for analysis in a clinical study was demonstrated, and statistically significant differences in wear were established for main effect for the materials under investigation. None of the composite resins examined approximated the amalgam alloy control in wear properties. Rank ordering of the materials with respect to wear was possible using this experimental design. Ranking of the materials for wear resistance using this research approach opens up other future research opportunities to correlate such properties as filler particle size, composition, and distribution with the data derived.

Analysis of Variance↗

PubMedDate not supplied

The influence of teeth on denture base processing accuracy.

The Michigan Computer Graphics Coordinate Measuring System was used to determine the influence of denture teeth on the accuracy of processed denture bases. Three different processing methods--compression molding, injection pressing, and vacuum-assisted resin pouring--were used. The presence of denture teeth was determined to affect the accuracy of the processed denture bases of all three techniques. For denture bases without teeth, the compression-molding technique demonstrated significant differences in accuracy; however, no significant differences were found in the injection-pressed or resin-poured denture bases.

Computer Graphics↗