Biomedical subjects

Paulette Spencer

Publications and source records attributed to Paulette Spencer.

30 records · Page 2Linked to original sources

PubMed2003

Micromechanical properties of demineralized dentin collagen with and without adhesive infiltration.

In a previous study, we reported the upper limit of Young's modulus of the unprotected protein at the dentin/adhesive interface to be 2 GPa. In this study, to obtain a more exact value of the moduli of the components at the d/a interface, we used demineralized dentin collagen with and without adhesive infiltration. The prepared samples were analyzed using micro-Raman spectroscopy (micro RS) and scanning acoustic microscopy (SAM). Using an Olympus UH3 SAM (Olympus Co., Tokyo), measurements were recorded with a 400 MHz burst mode lens (120 degrees aperture angle; nominal lateral resolution, 2.5 microm). A series of calibration curves were prepared using the relationship between the ultrasonically measured elastic moduli of a set of known materials and their SAM response. Finally, both the bulk and bar wave elastic moduli were computed for a set of 13 materials, including polymers, ceramics, and metals. These provided the rationale for using extensional wave measurements of the elastic moduli as the basis for extrapolation of the 400 MHz SAM data to obtain Young's moduli for the samples: E = 1.76 +/- 0.00 GPa for the collagen alone; E = 1.84 +/- 0.65 GPa for the collagen infiltrated with adhesive; E = 3.4 +/- 1.00 GPa for the adhesive infiltrate.

Bisphenol A-Glycidyl Methacrylate↗

PubMed2003

Dimensional accuracy and surface detail reproduction of two hydrophilic vinyl polysiloxane impression materials tested under dry, moist, and wet conditions.

STATEMENT OF PROBLEM: A major limitation of vinyl polysiloxane (VPS) impression materials is their hydrophobicity. There are 2 aspects to this problem, the wettability of the polymerized impression by dental gypsum materials and the ability of the unpolymerized material to wet intraoral tissues. To address this problem, manufacturers have added surfactants and labeled the new products as hydrophilic vinyl polysiloxane. PURPOSE: The purpose of this investigation was to compare dimensional accuracy and surface detail reproduction of 2 hydrophilic VPS impression materials, when used under dry, moist, and wet conditions. MATERIALS AND METHODS: A total of 102 impressions were made of stainless steel metal dies similar to those described in American Dental Association (ADA) specification 19. The dies had 2 vertical and 3 horizontal lines inscribed on their superior surfaces. Impressions were made under dry, moist, and wet conditions. Dimensional accuracy was measured by comparing the average length of the middle horizontal line in each impression to the same line on the metal die, by use of a measuring microscope with an accuracy of 0.001 mm. A 2-way analysis of variance and least significant difference post hoc test were used to compare mean dimensional changes (alpha=.05). Surface detail reproduction was evaluated in 2 ways: (1) by use of criteria similar to ADA specification 19 for detail reproduction, continuous replication of at least 2 of the 3 horizontal lines, and (2) by use of a method developed for this study that categorized the impressions as satisfactory or unsatisfactory based on their surface characteristics: presence of pits, voids, or roughness. Pearson chi(2) (alpha=.05) was used to compare detail reproduction results. RESULTS: Conditions (dry, moist, and wet) did not cause significant adverse effects on the dimensional accuracy of either material. The mean dimensional change and SD were 0.005% +/- 0.002% or less. With both surface detail analyses, dry, moist, and wet conditions had a significant effect on the detail reproduction of both materials (P<.05). Only under dry conditions did both impression materials continuously replicate at least 2 of the 3 horizontal lines 100% of the time. Under moist conditions, 82% of the Aquasil impressions and 100% of the Reprosil impressions were judged satisfactory, while under wet conditions, only 47% Aquasil and 11% Reprosil impressions were satisfactory. With the additional surface detail characterization, only under dry conditions were impressions produced with clinically acceptable surface quality (Aquasil 77% and Reprosil 100% satisfactory). CONCLUSIONS: Dimensional accuracy of both materials tested was well within ADA standards. Best surface detail results were obtained only under dry conditions for both materials.

Analysis of Variance↗

PubMed2003

Mechanical property characterization of resin cement after aqueous aging with and without cyclic loading.

OBJECTIVE: The purpose of this study was to determine changes in flexural properties of resin cement under cyclic loading and aqueous aging. METHODS: Panavia F flexural modulus and strength were measured by static loading to failure after 48-h, 31-d, and 60-d aqueous aging at 37 degrees C with and without cyclic loading at clinical stress levels. Six specimens were used for each experimental condition. Scanning electron microscopy (SEM) was also used to characterize the morphology of the fractured surfaces to potentially identify resin cement components particularly susceptible to degradation under simulated clinical function. RESULTS: A two-factor ANOVA (p< or =0.05) and Least Significant Difference post hoc test indicated that cyclic loading produced a significant increase in the flexural modulus with no significant effect on the flexural strength. In contrast, aqueous aging time produced a significant decrease in flexural strength with no effect on the flexural modulus. The SEM fracture analysis indicated that resin matrix fracture occurred in static-aqueous specimens; while in the aqueous-cycled specimens, resin matrix fracture occurred in addition to an increasing proportion of filler/resin interface fracture as a result of both increased aqueous aging and increased flexural cycles. SIGNIFICANCE: Evidence suggests that after aqueous aging with cyclic loading to simulate resin cement clinical function, initial degradation may be related to breakdown of the filler/resin interface bond. Such breakdown is potentially reflective of slow crack propagation that may contribute to in vivo resin cement cohesive failure.

Analysis of Variance↗

PubMed2002

Adhesive phase separation at the dentin interface under wet bonding conditions.

Under in vivo conditions, there is little control over the amount of water left on the tooth and, thus, there is the danger of leaving the dentin surface so wet that the bonding resin undergoes physical separation into hydrophobic and hydrophilic-rich phases. The purpose of this study was to investigate phase separation in 2,2-bis[4(2-hydroxy-3-methacryloyloxy-propyloxy)-phenyl] propane (BisGMA)-based adhesive using molecular microanalysis and to examine the effect of phase separation on the structural characteristics of the hybrid layer. Model BisGMA/HEMA (hydroxyethl methacrylate) mixtures with/without ethanol and commercial BisGMA-based adhesive (Single Bond) were combined with water at concentrations from 0 to 50 vol%. Macrophase separation in the BisGMA/HEMA/water mixtures was detected using cloud point measurements. In parallel with these measurements, the BisGMA/HEMA and adhesive/water mixtures were cast as films and polymerized. Molecular structure was recorded from the distinct features in the phase-separated adhesive using confocal Raman microspectroscopy (CRM). Human dentin specimens treated with Single Bond were analyzed with scanning electron microscopy (SEM) and CRM mapping across the dentin/adhesive interface. The model BisGMA/HEMA mixtures with ethanol and the commercial BisGMA-based adhesive experienced phase separation at approximately 25 vol% water. Raman spectra collected from the phase-separated adhesive indicated that the composition of the particles and surrounding matrix material was primarily BisGMA and HEMA, respectively. Based on SEM analysis, there was substantial porosity at the adhesive interface with dentin. Micro-Raman spectral analysis of the dentin/adhesive interface indicates that the contribution from the BisGMA component decreases by nearly 50% within the first micrometer. The morphologic results in corroboration with the spectroscopic data suggest that as a result of adhesive phase separation the hybrid layer is not an impervious 3-dimensional collagen/polymer network but a porous web characterized by hydrophobic BisGMA-rich particles distributed in a hydrophilic HEMA-rich matrix.

Bisphenol A-Glycidyl Methacrylate↗

PubMed2002

Analysis of acid-treated dentin smear debris and smear layers using confocal Raman microspectroscopy.

Smear layers are generally present on any dentin surface prepared with cutting instruments and are often the only available substrate for bonding. It is commonly reported that acid removes these layers, but to date there has been no chemical evidence to support this observation. Confocal Raman microspectroscopy was used to investigate changes in the composition and molecular structure of acid-treated smear debris and in situ dentin smear layers. The exposed dentin in human molars was abraded with 600-grit silicon carbide sandpaper. Raman spectra were acquired on the smear debris and collected from the sandpaper before and after treatment with 10% citric acid, 35% H3PO4, or 0.5M ethylenediaminetetraacetic acid (EDTA). The resultant smeared dentin samples were treated with one of the aforementioned reagents, and spectra were acquired at 1.0-microm intervals across the interfaces of the smear layers/demineralized dentin/mineralized dentin. Corresponding specimens were morphologically analyzed with scanning electron microscopy (SEM). The results showed that the composition of the smear debris and the in situ smear layers was a mixture of disorganized collagen and mineral. Spectral changes in the smear debris suggested that the disorganized collagen was denatured by acid treatment. The denatured collagen formed a gelatinous matrix around the mineral in the smear layer, thereby shielding it from the acid. The smear layers were not apparent in the SEM micrographs of acid-etched dentin prepared and processed with conventional techniques. The micro-Raman spectroscopic results presented in this study provide the first direct evidence that partially denatured collagen within smear layers is not removed and that the mineral is only partially removed with acids that represent conventional dentin adhesive etchants.

Acid Etching, Dental↗

PubMed2002

Quantifying adhesive penetration in adhesive/dentin interface using confocal Raman microspectroscopy.

Confocal Raman microspectroscopy (CRM) provides an important and novel means of analyzing the chemical composition of the adhesive/dentin (a/d) interface. The purpose of this study was to develop a method for quantitative determination of the degree of adhesive penetration at the a/d interface using CRM. Three commercial dentin adhesive systems [Scotchbond Multipurpose Plus (SBMP+), Single Bond (SB), and Primer Bond NT (PBNT)] based on the total etch and "wet" bonding technique were examined in this study. Human dentin specimens treated with these adhesives were analyzed with CRM mapping across the a/d interface. Also, Raman spectra were collected on model mixtures of adhesive and type I collagen, and the ratios of the relative intensities of the Raman bands corresponding to adhesive and collagen were used for the construction of calibration curves. By comparing the Raman band ratios of interface specimens to the calibration curves, the percent of adhesive as a function of spatial position across the a/d interface was determined. The results show that there is a gradual decrease in penetration as a function of position for all three adhesive systems while the adhesive concentration gradient decreases in the order of SBMP+ > SB > PBNT. These differences in penetration of the three adhesives at the a/d interface also are discussed relative to the composition and phase segregation in adhesives. Additionally, our results indicate that confocal Raman microspectroscopy is a reliable in situ analytical technique for simple and rapid quantitative determination of adhesive penetration at its interface with prepared dentin.

Adhesives↗

PubMed2002

Comparison of panoramic radiography and panoramic digital subtraction radiography in the detection of simulated osteophytic lesions of the mandibular condyle.

OBJECTIVE: The aim of this study was to compare panoramic temporomandibular joint radiography, unenhanced and color-enhanced digital-subtraction radiography with respect to detectability of simulated osteophytic lesions of the mandibular condyle. METHODS: Three dry human skulls with no obvious temporomandibular joint pathology were selected. Four sizes of bone chips were placed on the anterior aspect of the condyle at medial, central, and lateral locations. Panoramic radiographs were made with and without the chips in place. These paired radiographs were digitized, and unenhanced and color-enhanced digital-subtraction images of the original panoramic images were obtained. Eight observers evaluated 72 randomized images of each modality for the presence or absence of simulated osteophytic lesions of the mandibular condyle, grading the images on a 100-point scale. RESULTS: A(z) values for overall diagnostic accuracy of the three imaging modalities were 0.5376 for panoramic radiography, 0.7861 for unenhanced digital subtraction radiography, and 0.7923 for color-enhanced digital-subtraction radiography. Digital-subtraction radiography improved the detection accuracy of the original panoramic films. CONCLUSION: Panoramic radiographs were significantly less accurate in the detection of simulated osteophytic lesions of the mandibular condyle than the two digital-subtraction techniques.

Analysis of Variance↗

PubMed2002

Morphological and chemical characterization of the dentin/resin cement interface produced with a self-etching primer.

PURPOSE: The purpose of this study was to analyze a resin cement/dentin interface by comparing the diffusion of a resin cement into dentin surfaces pretreated with a self-etching primer with or without pretreatment by conventional acid etching. MATERIALS AND METHODS: Dentin surfaces of 8 unerupted human third molars were treated with a self-etch primer (Panavia 21) with or without conventional phosphoric acid pretreatment. Panavia 21 resin cement was applied according to manufacturer's instructions. Dentin/resin cement interface sections from each tooth were examined with scanning electron microscopy and micro-Raman spectroscopy. RESULTS: When the self-etch primer was used following conventional acid pretreatment, the resin cement did not penetrate to the depth of the zone of demineralized dentin, leaving a substantial area of exposed dentin matrix at the dentin/cement interface. In contrast, there was substantial resin cement diffusion throughout the demineralized dentin when the self-etch primer was used without acid etching pretreatment. CONCLUSION: The in vitro evaluation of resin cement penetration throughout the zone of demineralized dentin is an important step in identifying sites of exposed dentin matrix that may promote postoperative sensitivity and may leave the dentin/resin cement interface vulnerable to premature degradation under clinical conditions. In this study, the self-etch primer used alone produced substantial resin cement penetration and left no exposed dentin matrix at the dentin/resin cement interface.

Acid Etching, Dental↗

PubMedDate not supplied

Histomorphologic characterization of noncarious and caries-affected dentin/adhesive interfaces.

PURPOSE: The purpose of this study was to compare the dentin/adhesive interfacial characteristics when bonding to noncarious as well as caries-affected dentin. MATERIALS AND METHODS: Seven extracted, unerupted, third molars were sectioned into halves. Artificial caries was created on one-half of each tooth, leaving the other half as a control. Dentin surfaces were treated with UNO adhesive according to the manufacturer's instructions for the wet-bonding technique and under environmental conditions present in the oral cavity. Dentin/adhesive interface sections of each half-tooth were stained with Goldner's trichrome, a classic bone stain, and examined using light microscopy. The width of exposed collagen was measured directly from photomicrographs, and adhesive penetration was analyzed qualitatively. RESULTS: The degree and extent to which the adhesive encapsulated the demineralized dentin matrix were reflected in the color difference in the stained sections with the noncarious dentin sections showing a degree of collagen encapsulation superior to that of the caries-affected dentin sections. The overall mean widths of exposed collagen were significantly (p < or = .05) greater at the caries-affected dentin/adhesive interface, 8.6 (1.7) microm, as compared with those at the noncarious dentin/adhesive interface, 6.0 (1.5) microm. CONCLUSIONS: The morphologic characteristics of the caries-affected dentin/interface suggest an increase in the exposed collagen zone and a decrease in the quality of the adhesive infiltration when compared with noncarious dentin. The evidence suggests that dentin substrate characteristics have a significant effect on the dentin/adhesive interface structure.

Benzoates↗

PubMedDate not supplied

Physicochemical interactions at the dentin/adhesive interface using FTIR chemical imaging.

To date, much of our understanding of dentin bonding has been based on investigations performed on sound, healthy dentin. This is not the substrate generally encountered in clinical practice, rather dentists must frequently bond to caries-affected dentin. Because of the extreme complexity and variability of the caries-affected dentin substrate, conventional characterization techniques do not provide adequate information for defining those factors that impact bond formation. Using Fourier-transform infrared imaging, we characterized the inhomogeneities and compositional differences across the length and breadth of the caries-affected dentin/adhesive interface. Differences in mineral/matrix ratio, crystallinity, and collagen organization were noted in the comparison of caries-affected and healthy dentin. As compared to healthy dentin, there were striking differences in depth of demineralization, adhesive infiltration, and degree of conversion at the interface with caries-affected dentin.

Adhesiveness↗

PubMedDate not supplied

Micro-Raman imaging analysis of monomer/mineral distribution in intertubular region of adhesive/dentin interfaces.

It is generally proposed that bonding of resins to dentin results from infiltration of the adhesive monomers into the superficially demineralized dentin. However, it is still not clear how well the mineral phase of dentin is removed and how far each monomer penetrates into the thin zone of "wet" demineralized dentin. The quality and molecular structure of adhesive/dentin interfaces formed under "wet" bonding conditions are studied using 2-D Raman microspectroscopic mapping/imaging techniques. Micro-Raman imaging analysis of the adhesive/dentin interface provides a reliable and powerful means of identifying the degree and depth of dentin demineralization, adhesive monomer distribution, and flaws or defects in the pattern of adhesive penetration. The image of mineral reveals a partially demineralized layer on the top of dentin substrate. Adhesive monomers readily penetrate into dentin tubules and spread into intertubular region through open tubules. The extent of adhesive monomer penetration is higher in the intertubular regions close to tubules as compared to the middle regions between the tubules. The diffusion of resin monomers differs substantially. In a comparison with a hydrophilic monomer, the hydrophobic monomer resists diffusion into the demineralized intertubular dentin area.

Absorption↗

PubMedDate not supplied

Exploring the nature of acid-resistant hybrid layer with wet bonding.

The nature of the hybrid layer (HL) following chemical treatment has not been resolved. The effects of chemical treatments and polishing on HL morphology and composition were investigated using micro-Raman spectroscopy and SEM. Polished and unpolished SingleBond adhesive/dentin (a/d) interfaces from the same tooth were randomly selected for one of the following treatments: a) 5N HCl followed by 5%NaOCl; b) 5%NaOCl; c) 5%NaOCl and sonication; d) 5%NaOCl followed by 5N HCl. The results indicated that the HCl-NaOCl treatment could obscure the "true" HL in the unpolished a/d interfaces that were actually porous. The composition and morphology of the polished interface specimens were largely unchanged by the above treatments. Descriptions of HL quality are commonly based on the acid reactivity of polished specimens. The results of this study indicate that polishing dramatically alters the native composition, increasing its acid-resistance, and thus, this procedure could lead to false conclusions about HL quality.

Bisphenol A-Glycidyl Methacrylate↗