Search PubMed⌕ Search

Biomedical subjects

P R Cavanagh

Publications and source records attributed to P R Cavanagh.

At least 19 recordsLinked to original sources
PubMed2006

Determination of elastomeric foam parameters for simulations of complex loading.

BACKGROUND: Finite element (FE) analysis has shown promise for the evaluation of elastomeric foam personal protection devices. Although appropriate representation of foam materials is necessary in order to obtain realistic simulation results, material definitions used in the literature vary widely and often fail to account for the multi-mode loading experienced by these devices. This study aims to provide a library of elastomeric foam material parameters that can be used in FE simulations of complex loading scenarios. METHOD OF APPROACH: Twelve foam materials used in footwear were tested in uni-axial compression, simple shear and volumetric compression. For each material, parameters for a common compressible hyperelastic material model used in FE analysis were determined using: (a) compression; (b) compression and shear data; and (c) data from all three tests. RESULTS: Material parameters and Drucker stability limits for the best fits are provided with their associated errors. The material model was able to reproduce deformation modes for which data was provided during parameter determination but was unable to predict behavior in other deformation modes. CONCLUSIONS: Simulation results were found to be highly dependent on the extent of the test data used to determine the parameters in the material definition. This finding calls into question the many published results of simulations of complex loading that use foam material parameters obtained from a single mode of testing. The library of foam parameters developed here presents associated errors in three deformation modes that should provide for a more informed selection of material parameters.

Cellulose↗
PubMed2002

Modifiable determinants of bone status in young women.

The purpose of this study was to evaluate the contributions of exercise, fitness, body composition, and calcium intake during adolescence to peak bone mineral density and bone structural measurements in young women. University Hospital and 75 healthy, white females in the longitudinal Penn State Young Women's Health Study were included. Body composition, total body, and hip bone mineral density (BMD) were measured by dual-energy X-ray absorptiometry (DXA), exercise scores by sports-exercise questionnaire during ages 12-18 years, and estimated aerobic capacity by bike ergometry. Section modulus values (a measurement of bending strength) cross-sectional area (CSA), subperiosteal width, and cortical thickness were calculated from DXA scan data for the femoral neck and femoral shaft. Calcium intakes were calculated from 39 days of prospective food records collected at 13 timepoints between ages 12 and 20 years; supplemental calcium intakes were included. Section moduli at the femoral neck and shaft were correlated significantly with lean body mass, sports-exercise scores (R(2) = 0.07-0.19, p < 0.05), and aerobic capacity (R(2) = 0.06-0.57, p < 0.05). Sports-exercise scores correlated with BMD at the femoral neck and shaft. Average total daily calcium intake at age 12-20 years ranged from 486 to 1958 mg/day and was not significantly associated with total or regional peak BMD or bone structure measures at 20 years of age. It was shown that achievable levels of exercise and fitness have a favorable effect on BMD and section modulus of the femoral neck and femoral shaft in young adult women, whereas daily calcium intake of >500 mg in female adolescents appears to have little, if any effect.

Adolescent↗
PubMed2001

In vitro modeling of human tibial strains during exercise in micro-gravity.

Prolonged exposure to micro-gravity causes substantial bone loss (Leblanc et al., Journal of Bone Mineral Research 11 (1996) S323) and treadmill exercise under gravity replacement loads (GRLs) has been advocated as a countermeasure. To date, the magnitudes of GRLs employed for locomotion in space have been substantially less than the loads imposed in the earthbound 1G environment, which may account for the poor performance of locomotion as an intervention. The success of future treadmill interventions will likely require GRLs of greater magnitude. It is widely held that mechanical tissue strain is an important intermediary signal in the transduction pathway linking the external loading environment to bone maintenance and functional adaptation; yet, to our knowledge, no data exist linking alterations in external skeletal loading to alterations in bone strain. In this preliminary study, we used unique cadaver simulations of micro-gravity locomotion to determine relationships between localized tibial bone strains and external loading as a means to better predict the efficacy of future exercise interventions proposed for bone maintenance on orbit. Bone strain magnitudes in the distal tibia were found to be linearly related to ground reaction force magnitude (R(2)>0.7). Strain distributions indicated that the primary mode of tibial loading was in bending, with little variation in the neutral axis over the stance phase of gait. The greatest strains, as well as the greatest strain sensitivity to altered external loading, occurred within the anterior crest and posterior aspect of the tibia, the sites furthest removed from the neutral axis of bending. We established a technique for estimating local strain magnitudes from external loads, and equations for predicting strain during simulated micro-gravity walking are presented.

Aged↗
PubMed2001

Accuracy of the functional method of hip joint center location: effects of limited motion and varied implementation.

Accurate location of the hip joint center is essential for computation of hip kinematics and kinetics as well as for determination of the moment arms of muscles crossing the hip. The functional method of hip joint center location involves fitting a pelvis-fixed sphere to the path traced by a thigh-fixed point while a subject performs hip motions; the center of this sphere is the hip joint center. The aim of the present study was to evaluate the potential accuracy of the functional method and the dependence of its accuracy on variations in its implementation and the amount of available hip motion. The motions of a mechanical linkage were studied to isolate the factors of interest, removing errors due to skin movement and the palpation of bony landmarks that are always present in human studies. It was found that reducing the range of hip motion from 30 degrees to 15 degrees did significantly increase hip joint center location errors, but that restricting motion to a single plane did not. The magnitudes of these errors, however, even in the least accurate cases, were smaller than those previously reported for either the functional method or other methods based on pelvis measurements of living subjects and cadaver specimens. Neither increasing the number of motion data observations nor analyzing the motion of a single thigh marker (rather than the centroid of multiple markers) was found to significantly increase error. The results of this study (1) imply that the limited range of motion that is often evident in subjects with hip pathology does not preclude accurate determination of the hip joint center when the functional method is used; and (2) provide guidelines for the use of the functional method in human subjects.

Biomechanical Phenomena↗
PubMed2001

Increased variability of continuous overground walking in neuropathic patients is only indirectly related to sensory loss.

The present study was conducted to determine if peripheral neuropathy leads to significant changes in locomotor variability. Fourteen patients with severe peripheral neuropathy and 12 gender-, age-, height-, and weight-matched non-diabetic controls participated. Sagittal plane angles of the right hip, knee, and ankle joints and tri-axial accelerations of the trunk were measured during 10 min of continuous overground walking. Standard deviations of stride times and stride-to-stride standard deviations of each kinematic variable were calculated. Neuropathic patients walked slower and exhibited some increases in locomotor variability compared to control subjects. However, these increases in gait variability were primarily linked to reductions in self-selected walking speed and were not directly attributable to sensory loss itself.

Aged↗
PubMed2001

Vibration perception threshold testing in patients with diabetic neuropathy: ceiling effects and reliability.

AIMS: To test the reliability of a new vibrometer (Maxivibrometer) which was constructed so that vibration perception threshold (VPT) could be determined without the disadvantage of the off-scale measurements frequently experienced with the Biothesiometer. METHODS: The two devices were compared and tested on a group of diabetic neuropathic subjects and a group of healthy, matched control subjects. VPT was tested on the plantar surface of the feet. RESULTS: The Maxivibrometer gave an actual measurement in all cases even if subjects were severely neuropathic. The replication-to-replication and day-to-day intraclass correlation coefficients for the Maxivibrometer VPT were, except in one case, above 0.94, indicating excellent reliability. The Biothesiometer VPT could also be measured with excellent reliability but only within a limited range of mild to moderate neuropathy, so it appears to be an appropriate screening tool. The replication-to-replication intraclass correlation coefficient was 0.93. CONCLUSIONS: Because VPT could be measured over a wide range with the Maxivibrometer, it was demonstrated that loss of sensation in diabetic neuropathy can progress far beyond the maximum VPT value of the Biothesiometer. The wide measurement range and the excellent reliability make the Maxivibrometer a valuable research tool to quantify loss of sensation, particularly in the presence of severe neuropathy and to record changes over time. Diabet. Med. 18, 469-475 (2001)

Diabetic Neuropathies↗
PubMed2001

Gender differences in adult foot shape: implications for shoe design.

PURPOSE: To analyze gender differences in foot shape in a large sample of young individuals. METHODS: Univariate t-tests and multivariate discriminant analyses were used to assess 1) significant differences between men and women for each foot and leg dimension, standardized to foot length, 2) the reliability of classification into gender classes using the absolute and standardized variable sets, and 3) the relative importance of each variable to the discrimination between men and women. RESULTS: Men have longer and broader feet than women for a given stature. After normalization of the measurements by foot length, men and women were found to differ significantly in two calf, five ankle, and four foot shape variables. Classification by gender using absolute values was correct at least 93% of the time. Using the variables standardized to foot length, gender was correctly classified 85% of the time. CONCLUSIONS: This study demonstrates that female feet and legs are not simply scaled-down versions of male feet but rather differ in a number of shape characteristics, particularly at the arch, the lateral side of the foot, the first toe, and the ball of the foot. These differences should be taken into account in the design and manufacture of women's sport shoes.

Adult↗
PubMed2001

Local dynamic stability versus kinematic variability of continuous overground and treadmill walking.

This study quantified the relationships between local dynamic stabiliht and variabilitr during continuous overground and treadmill walking. Stride-to-stride standard deviations were computed from temporal and kinematic data. Marimum finite-time Lyapunov exponents were estimated to quantify local dynamic stability. Local stability of gait kinematics was shown to be achieved over multiple consecutive strides. Traditional measures of variability poorly predicted local stability. Treadmill walking was associated with significant changes in both variability and local stability. Thus, motorized treadmills may produce misleading or erroneous results in situations where changes in neuromuscular control are likely to affect the variability and/or stability of locomotion.

Adult↗
PubMed2000

Measurement of the screw-home motion of the knee is sensitive to errors in axis alignment.

Measurements of joint angles during motion analysis are subject to error caused by kinematic crosstalk, that is, one joint rotation (e. g., flexion) being interpreted as another (e.g., abduction). Kinematic crosstalk results from the chosen joint coordinate system being misaligned with the axes about which rotations are assumed to occur. The aim of this paper is to demonstrate that measurement of the so-called "screw-home" motion of the human knee, in which axial rotation and extension are coupled, is especially prone to errors due to crosstalk. The motions of two different two-segment mechanical linkages were examined to study the effects of crosstalk. The segments of the first linkage (NSH) were connected by a revolute joint, but the second linkage (SH) incorporated gearing that caused 15 degrees of screw-home rotation to occur with 90 degrees knee flexion. It was found that rotating the flexion axis (inducing crosstalk) could make linkage NSH appear to exhibit a screw-home motion and that a different rotation of the flexion axis could make linkage SH apparently exhibit pure flexion. These findings suggest that the measurement of screw-home rotation may be strongly influenced by errors in the location of the flexion axis. The magnitudes of these displacements of the flexion axis were consistent with the inter-observer variability seen when five experienced observers defined the flexion axis by palpating the medial and lateral femoral epicondyles. Care should be taken when interpreting small internal-external rotations and abduction-adduction angles to ensure that they are not the products of kinematic crosstalk.

Adult↗
PubMed2000

Slower speeds in patients with diabetic neuropathy lead to improved local dynamic stability of continuous overground walking.

Patients with diabetic peripheral neuropathy are significantly more likely to fall while walking than subjects with intact sensation. While it has been suggested that these patients walk slower to improve locomotor stability, slower speeds are also associated with increased locomotor variability, and increased variability has traditionally been equated with loss of stability. If the latter were true, this would suggest that slowing down, as a locomotor control strategy, should be completely antithetical to the goal of maintaining stability. The present study resolves these seemingly paradoxical findings by using methods from nonlinear time series analysis to directly quantify the sensitivity of the locomotor system to local perturbations that are manifested as natural kinematic variability. Fourteen patients with severe peripheral neuropathy and 12 gender-, age-, height-, and weight-matched non-diabetic controls participated. Sagittal plane angles of the right hip, knee, and ankle joints and tri-axial accelerations of the trunk were measured during 10 min of continuous overground walking at self-selected speeds. Maximum finite-time Lyapunov exponents were computed for each time series to quantify the local dynamic stability of these movements. Neuropathic patients exhibited slower walking speeds and better local dynamic stability of upper body movements in the horizontal plane than did control subjects. The differences in local dynamic stability were significantly predicted by differences in walking speed, but not by differences in sensory status. These results support the hypothesis that reductions in walking speed are a compensatory strategy used by neuropathic patients to maintain dynamic stability of the upper body during level walking.

Aged↗
PubMed2000

Stair negotiation in older people: a review.

Locomotion on stairs is among the most challenging and hazardous activities of daily living for older individuals. This is evidenced by the reports that stair falls account for more than 10% of fatal fall accidents. The demands that stairs place on the musculoskeletal and cardiovascular systems are compounded by the need for input from the somatosensory, visual, and vestibular systems at various stages in the task. Many of these collaborating systems deteriorate with aging, thus increasing the difficulty and risk of failure in a task that inherently involves exposure to significant danger. The task itself varies in its degree of challenge depending on many structural and environmental factors that are outside the control of the stair user. This review explores existing literature in the area of stair negotiation by older persons in an effort to define the key factors associated with difficulty and safety on stairs and to interpret these findings in the light of possible interventions that could increase stair safety. Further research is needed to ensure that current recommendations for stair design are suitable for older stair users. A Glossary of Terms is also provided.

Accidental Falls↗
PubMed2000

Design criteria for rigid rocker shoes.

In this study nine different rigid rocker shoe designs were tested in 17 symptom-free male subjects and compared with the control condition of a flexible, non-rockered extra-depth shoe with the same flat insole. Effects of both rocker height and axis location were explored. Peak pressure was reduced at most forefoot locations by rocker shoes, but increased in the midfoot and heel. Axis location was found to have an important effect, particularly on hallux pressures. On average the best axis location for reducing metatarsal head (MTH) pressure was in the region of 55-60% of shoe length, while for the toes it was 65%. There was a mean trend towards optimal reduction of pressure in one of the rocker shoe conditions at each anatomical location, but the axis position for this optimal placement was variable across subjects and anatomical locations. While most configurations of the rocker shoes were superior to the control shoe, no single configuration was optimal for all subjects at all sites or even for all subjects at the same site. Therefore, some form of plantar pressure measurement in conjunction with gait training to ensure correct use of the rocker shoes would appear to be essential if the pressure reducing effect of the rigid rocker bottom shoe is to be optimized.

Adult↗
PubMed1999

Structural and functional predictors of regional peak pressures under the foot during walking.

The objective of this study was to identify structural and functional factors which are predictors of peak pressure underneath the human foot during walking. Peak plantar pressure during walking and eight data sets of structural and functional measures were collected on 55 asymptomatic subjects between 20 and 70 yr. A best subset regression approach was used to establish models which predicted peak regional pressure under the foot. Potential predictor variables were chosen from physical characteristics, anthropometric data, passive range of motion (PROM), measurements from standardized weight bearing foot radiographs, mechanical properties of the plantar soft tissue, stride parameters, foot motion in 3D, and EMG during walking. Peak pressure values under the rearfoot, midfoot, MTH1, and hallux were measured. Heel pressure was a function of linear kinematics, longitudinal arch structure, thickness of plantar soft tissue, and age. Midfoot pressure prediction was dominated by arch structure, while MTH1 pressure was a function of radiographic measurements, talo-crural joint motion, and gastrocnemius activity. Hallux pressure was a function of structural measures and MTP1 joint motion. Foot structure and function predicted only approximately 50% of the variance in peak pressure, although the relative contributions in different anatomical regions varied dramatically. Structure was dominant in predicting peak pressure under the midfoot and MTH1, while both structure and function were important at the heel and hallux. The predictive models developed in this study give insight into potential etiological factors associated with elevated plantar pressure. They also provide direction for future studies designed to reduce elevated pressure in "at-risk" patients.

Adult↗
PubMed1999

Plantar soft tissue thickness during ground contact in walking.

A technique is introduced for the measurement of plantar soft tissue thickness during barefoot walking. Subjects stepped into an adjustable Plexiglas frame which ensured that the required bony landmarks were appropriately positioned relative to a linear ultrasound probe connected to a conventional 7.5 MHz ultrasound scanner. Clear images of the metatarsal condyles or other foot bones were obtained throughout ground contact. Subsequent analysis of the video taped images using a motion analysis system allowed the tissue displacement to be calculated as a function of time. The tissue underneath the second metatarsal head was shown to undergo an average maximum compression of 45.7% during the late stages of ground contact during first step gait in a group of five normal subjects with a mean unloaded tissue thickness of 15.2 mm. The technique has a number of applications, including use in the validation of deformation predicted by finite element models of the soft tissue of the foot, and the study of alterations in the cushioning properties of the heel by devices which constrain the displacement of the heel pad.

Adult↗
PubMed1999

Neuropathic gait shows only trends towards increased variability of sagittal plane kinematics during treadmill locomotion.

Patients with diabetes mellitus (DM) and peripheral neuropathy (PN) are at greater risk of falling and of suffering injuries during falls. It has been hypothesized that PN leads to changes in gait variability that may account for this increased risk. The purpose of this investigation was to analyze the variability of the sagittal plane kinematics of diabetic neuropathic (NP), diabetic non-neuropathic (NNP) and age- and weight-matched control subjects (Control) during motorized treadmill walking at constant speed. While there were distinct trends towards increased variability within the three diagnostic groups (NP > NNP > Control) for several measures of gait variability, most of these trends were not statistically significant. We hypothesize that motorized treadmill walking may be inherently less variable than overground walking and that statistical measures of variability may not be sufficient to fully characterize stride-to-stride variability in human locomotion.

Accidental Falls↗
PubMed1999

Evaluation of a Treadmill with Vibration Isolation and Stabilization (TVIS) for use on the International Space Station.

A treadmill with vibration isolation and stabilization designed for the International Space Station (ISS) was evaluated during Shuttle mission STS-81. Three crew members ran and walked on the device, which floats freely in zero gravity. For the majority of the more than 2 hours of locomotion studied, the treadmill showed peak to peak linear and angular displacements of less than 2.5 cm and 2.5 degrees, respectively. Vibration transmitted to the vehicle was within the microgravity allocation limits that are defined for the ISS. Refinements to the treadmill and harness system are discussed. This approach to treadmill design offers the possibility of generating 1G-like loads on the lower extremities while preserving the microgravity environment of the ISS for structural safety and vibration free experimental conditions.

Equipment Design↗
PubMed1999

Elevated plantar pressure and ulceration in diabetic patients after panmetatarsal head resection: two case reports.

Panmetatarsal head resection (variously called forefoot arthroplasty, forefoot resection arthroplasty, the Hoffman procedure, and the Fowler procedure) was developed for the relief of pain and deformity in rheumatoid arthritis. Although there are successful retrospective series reported in the literature, such an approach is not supported by carefully designed controlled trials. This procedure has also been advocated by some for the relief of plantar pressure in diabetic patients who are at risk for plantar ulceration. The efficacy of the procedure in this context is not supported by existing pressure measurements on rheumatoid arthritis patients in the literature, which has tended to show that although pain relief is obtained, the procedure results in elevation of forefoot pressure. Case reports are described of two patients (three feet) with sensory neuropathy who presented to our clinic 1 to 2 years after panmetatarsal head resections had been performed. Peak plantar pressures in these feet during first step gait were above the 99th percentile and outside the measuring range of the device used (EMED SF platform; NOVEL Electronics Inc., St. Paul, MN). Both patients had also experienced plantar ulcers subsequent to the surgery. Combining the information on patients with rheumatoid arthritis (RA) with that from our two case studies, we conclude that panmetatarsal head resection does not necessarily eliminate focal regions of elevated plantar pressure.

Aged↗