Biomedical subjects

Mathias Ulbricht

Publications and source records attributed to Mathias Ulbricht.

7 recordsLinked to original sources

PubMed2007

Permeability and electrokinetic characterization of poly(ethylene terephthalate) capillary pore membranes with grafted temperature-responsive polymers.

Poly(ethylene terephthalate) (PET) track-etched membranes with average pore diameters of 692 and 1629 nm were functionalized using the monomer N-isopropylacrylamide (NIPAAm) and a photoinitiated "grafting-from" approach in which a surface-selective reaction has been most efficiently achieved by combinations of the unmodified PET surface with benzophenone and, alternatively, of an aminated PET surface with benzophenone carboxylic acid. Consistent estimations of the pore diameters of the base PET membranes and of the effective grafted polyNIPAAm layer thicknesses on the PET pore walls were possible only on the basis of the permeabilities measured with aqueous solutions of higher ionic strength (e.g., 0.1 M NaCl). However, the permeabilities measured with ultrapure water indicated that the "electroviscous effect" was significant for both base membranes. The influences of membrane pore diameter, surface charge, and solution ionic strength could be interpreted in the framework of the space-charge model. Functionalized membranes with collapsed grafted polymer hydrogel layer thicknesses of a few nanometers exhibited almost zero values of the zeta potential estimated from the trans-membrane streaming potential measurements. This was caused by a "hydrodynamic screening" of surface charge by the neutral hydrogel. Very pronounced changes in permeability as a function of temperature were measured for PET membranes with grafted polyNIPAAm layers, and the effective layer thickness in the swollen state--here up to approximately 300 nm--correlated well with the degree of functionalization. The subtle additional effects of solution ionic strength on the hydrodynamic layer thickness at 25 degrees C were different from the effects for the base PET membranes and could be explained by a variation in the degree of swelling, resembling a "salting-out" effect. Overall, it had been demonstrated that the functionalized capillary pore membranes are well suited for a detailed and quantitative evaluation of the relationships between the synthesis, the structure, and the function of grafted stimuli-responsive polymer layers.

Journal Article↗

PubMed2006

Macroporous Poly(N-isopropylacrylamide) hydrogels with adjustable size "cut-off" for the efficient and reversible immobilization of biomacromolecules.

Poly(N-isopropylacrylamide) (PNIPA) hydrogels with varied degree of crosslinking (DC) were synthesized by using poly(ethylene glycol) (PEG) as an additive. A phase separated ("macroporous") morphology was formed when using PEG contents of > or = 20 wt.-%. Temperature-dependent degrees of swelling had been measured, and average mesh sizes of the swollen polymer network had been calculated. The loading of the hydrogels with labelled dextrans with various molar masses and bovine serum albumin (BSA)-via swelling of the shrunken gel in a cold solution-and their subsequent unloading-via immersion in hot water-were studied in detail. The loading efficiencies were close to zero for PNIPA prepared at PEG contents of < or = 10 wt.-%, and they increased sharply to about 100% for PNIPA prepared with PEG contents of > or = 20 wt.-%. A complete unloading was achieved as well. For macroporous PNIPA prepared at 40 wt.-% PEG content, the loading efficiency was a function of the DC, and the "cut-off" observed as a function of dextran or protein size correlated with the mesh size of the hydrogel. The function of these "smart" hydrogels can be explained by the temperature-induced "pumping" of the solution into the gel bulk via the permanent pores, along with an uptake into the adjacent hydrogel network. Those materials could be used as matrices for the efficient and reversible immobilization of (bio)macromolecules.

Acrylic Resins↗

PubMed2005

Size-selective protein adsorption to polystyrene surfaces by self-assembled grafted poly(ethylene glycols) with varied chain lengths.

We report about the surface modification of polystyrene (PSt) with photoreactive alpha-4-azidobenzoyl-omega-methoxy poly(ethylene glycol)s (ABMPEG) of three different molecular weights (MWs of approximately 2, approximately 5, and approximately 10 kg/mol) and with two poly(ethylene glycol)/poly(propylene glycol) triblock copolymers (PEG-PPG-PEG) of about identical PEG/PPG ratio (80/20, w/w) and MW(PEG) of approximately 3 and approximately 6 kg/mol, all via adsorption from aqueous solutions. For ABMPEGs, an additional UV irradiation was used for photografting to the PSt. Contact angle (CA) and atomic force microscopy data revealed pronounced differences of the hydrophilicity/hydrophobicity and topography of the surfaces as a function of PEG type and concentration used for the modification. In all cases, an incomplete coverage of the PSt was observed even after modification at the highest solution concentrations (10 g/L). However, clear differences were seen between PEG-PPG-PEGs and ABMPEGs; only for the latter was a nanoscale-ordered interphase structure with an influence of MW(PEG) on the PEG density observed; after modification at the same solution concentrations, the density was significantly higher for lower MW(PEG). The adsorption of three proteins, myoglobin (Mgb), bovine serum albumin (BSA), and fibrinogen to the various surfaces was analyzed by surface plasmon resonance. Pronounced differences between the two PEG types with respect to the reduction of protein adsorption were found. At high, but still incomplete, surface coverage and similar CA, the shielding of ABMPEG layers toward the adsorption of Mgb and BSA was much more efficient; e.g., the adsorbed Mgb mass relative to that of unmodified PSt was reduced to 10% for ABMPEG 2 kg/mol while for both PEG-PPG-PEGs the Mgb mass was still around 100%. In addition, for the ABMPEG layers an effect of MW(PEG) on adsorbed protein mass-decrease with decreasing MW-could be confirmed; and the highest Mgb/BSA selectivities were also observed. A "two-dimensional molecular sieving", based on PEG molecules having a nanoscale order at the hydrophobic substrate polymer surface has been proposed, and the main prerequisites were the use of PEG conjugates which are suitable for an "end-on" grafting (e.g., ABMPEGs), the use of suitable (not too high) concentrations for the surface modification via adsorption/self-assembly, optionally the photografting on the substrate (possible only for ABMPEG), and presumably, a washing step to remove the excess of unbound PEGs. The results of this study also strongly support the hypothesis that the biocompatibility of hydrophobic materials can be very much improved by PEG modifications at surface coverages that are incomplete but have an ordered layer structure controlled by the size and steric interactions of surface-bound PEGs.

Adsorption↗

PubMed2005

Electrochemical and other transport properties of nanoporous track-etched membranes studied by the current switch-off technique.

Measurements of transient membrane potential after current switch-off have been used to study the electrochemical and other transport properties of nanoporous track-etched membranes (pore diameter of 24 nm) in KCl solutions of various concentrations. Due to their identical straight cylindrical pores within the nanorange, those membranes are a suitable object for the studies of fundamentals of nanofluidics. We have developed a theory, which enabled us to interpret the transients of membrane potential in terms of such properties as the ion transport numbers, the membrane diffusion permeability, and the specific chemical capacity. The fitted values have been further interpreted within the scope of the space-charge model and revealed good self-consistency. The dependence of fitted values of the surface charge density on salt concentration was in agreement with the mechanism of fixed charge formation due to the dissociation of weakly acidic groups, and the surface charge density corresponded well to the measurements by an independent method. Thus, our measurements have revealed a quantitative applicability of standard space-charge model to the description of electrochemical phenomena and electrolyte diffusion in straight cylindrical pores of tens of nanometers in diameter. Proceeding from our data, we could estimate the limiting current densities for our nanofluidic system. They have turned out to be more than 2 orders of magnitude lower than usually encountered in microfluidic systems with electro-osmotic fluid delivery. That finding may point to a considerable handicap in the application of such nanofluidic elements in microsystems.

Journal Article↗

PubMed2004

Membrane separations using molecularly imprinted polymers.

This review presents an overview on the promising field of molecularly imprinted membranes (MIM). The focus is onto the separation of molecules in liquid mixtures via membrane transport selectivity. First, the status of synthetic membranes and membrane separation technology is briefly summarized, emphasizing the need for novel membranes with higher selectivities. Innovative principles for the preparation of membranes with improved or novel functionality include self-assembly or supramolecular aggregation as well as the use of templates. Based on a detailed analysis of the literature, the main established preparation methods for MIM are outlined: simultaneous membrane formation and imprinting, or preparation of imprinted composite membranes. Then, the separation capability of MIM is discussed for two different types, as a function of their barrier structure. Microporous MIM can continuously separate mixtures based on facilitated diffusion of the template, or they can change their permeability in the presence of the template ("gate effect"). Macroporous MIM can be developed towards molecule-specific membrane adsorbers. Emerging further combinations of molecularly imprinted polymers (MIPs), especially MIP nanoparticles or microgels, with membranes and membrane processes are briefly outlined as well. Finally, the application potential for advanced MIM separation technologies is summarized.

Membranes, Artificial↗

PubMed2003

Affinity membranes as a tool for life science applications.

As a matrix for affinity membrane technology we chose a flat-sheet microfiltration membrane based on polypropylene. Using photopolymerization to graft epoxy groups onto the pore surface, we worked with glycidylmethacrylate as a monomer. We developed optimized, efficient, and mild UV irradiation conditions for the two-step photografting process practically preserving the given pore structure of the base membrane. A grafting degree of up to 1.2 mg/cm(2) per surface area of the membrane was obtained. The poly-propylene membrane surface became significantly more hydrophilic. Introduction of epoxy groups allowed a stable covalent immobilization of the protein streptavidin serving as receptor for affinity ligand binding. A relatively high streptavidin immobilization capacity of about 65 micro g/cm(2) per surface area of the membrane was obtained. Apparently, only about two of the binding sites of the immobilized streptavidin were available for biotin recognition. We also found that the oriented immobilization of biotinylated alkaline phosphatase onto the surface via a streptavidin bridge increased the specific enzymatic activity about sixfold compared with random immobilization of this enzyme.

Biochemistry↗

PubMedDate not supplied

Polymerization of glucans by enzymatically active membranes.

Conventional enzyme membrane reactors are not appropriate for a continuous synthesis of macromolecules and simultaneous product release. By immobilizing the enzyme in sufficiently large pores of a membrane an ensemble of miniaturized bioreactors is created. Product molecules are continuously removed from the enzyme by the flow of the reaction mixture across the membrane. Additionally, by varying the flow rate, it ought to be possible to influence the substrate as well as the enzyme-product residence times and thereby the product macromolecule's size. In this paper we present the first results of experiments involving enzymatic 1,4-alpha-glucan synthesis, using sucrose as substrate, maltooligosaccharides (DP 3-6) as primers, and membrane-immobilized amylosucrase. Epoxy groups for a covalent enzyme immobilization were generated on polypropylene microfiltration membranes by heterogeneous photoinitiated graft polymerization of glycidyl methacrylate. The influence of primer concentration and flow rate through the enzyme-membrane on amylosucrase activity, molecule growth, and coupling efficiency for glucose (% of coupled glucose versus free glucose) were investigated. The enzymatically mediated chain elongation of maltooligosaccharides by the successive addition of glucose units was achieved for the first time in a transmembrane process utilizing amylosucrase membranes.

Bioreactors↗