Biomedical subjects

Mark J Mondrinos

Publications and source records attributed to Mark J Mondrinos.

5 recordsLinked to original sources

PubMed2006

Co-electrospun poly(lactide-co-glycolide), gelatin, and elastin blends for tissue engineering scaffolds.

In this study, we describe composite scaffolds composed of synthetic and natural materials with physicochemical properties suitable for tissue engineering applications. Fibrous scaffolds were co-electrospun from a blend of a synthetic biodegradable polymer (poly(lactic-co-glycolic acid), PLGA, 10% solution) and two natural proteins, gelatin (denatured collagen, 8% solution) and alpha-elastin (20% solution) at ratios of 3:1:2 and 2:2:2 (v/v/v). The resulting PLGA-gelatin-elastin (PGE) fibers were homogeneous in appearance with an average diameter of 380 +/- 80 nm, which was considerably smaller than fibers made under identical conditions from the starting materials (PLGA, 780 +/- 200 nm; gelatin, 447 +/- 123 nm; elastin, 1060 +/- 170 nm). Upon hydration, PGE fibers swelled to an average fiber diameter of 963 +/- 132 nm, but did not disintegrate. Importantly, PGE scaffolds were stable in an aqueous environment without crosslinking and were more elastic than those made of pure elastin fibers. To investigate the cytocompatibility of PGE, we cultured H9c2 rat cardiac myoblasts and rat bone marrow stromal cells (BMSCs) on fibrous PGE scaffolds. We found that myoblasts grew equally as well or slightly better on the scaffolds than on tissue-culture plastic. Microscopic evaluation confirmed that myoblasts reached confluence on the scaffold surfaces while simultaneously growing into the scaffolds. Histological characterization of the PGE constructs indicated that BMSCs penetrated into the center of scaffolds and began proliferating shortly after seeding. Our results suggest that fibrous scaffolds made of PGE and similar biomimetic blends of natural and synthetic polymers may be useful for engineering soft tissues, such as heart, lung, and blood vessels.

Animals↗

PubMed2006

Heterogeneous breast tumoroids: An in vitro assay for investigating cellular heterogeneity and drug delivery.

Breast tumors are typically heterogeneous and contain diverse subpopulations of tumor cells with differing phenotypic properties. Planar cultures of cancer cell lines are not viable models of investigation of cell-cell and cell-matrix interactions during tumor development. This article presents an in vitro coculture-based 3-dimensional heterogeneous breast tumor model that can be used in drug resistance and drug delivery investigations. Breast cancer cell lines of different phenotypes (MDAMB231, MCF7, and ZR751) were cocultured in a rotating wall vessel bioreactor to form a large number of heterogeneous tumoroids in a single cell culture experiment. Cells in the rotating vessels were labeled with Cell Tracker fluorescent probes to allow for time course fluorescence microscopy to monitor cell aggregation. Histological sections of tumoroids were stained with hematoxylin and eosin, progesterone receptor, E-cadherin (E-cad), and proliferation marker ki67. In vitro tumoroids developed in this study recapture important features of the temporal-spatial organization of solid tumors, including the presence of necrotic areas at the center and higher levels of cell division at the tumor periphery. E-cad-positive MCF7 cells form larger tumoroids than E-cad-negative MDAMB231 cells. In heterogeneous tumors, the irregular surface roughness was mainly due to the presence of MDAMB231 cells, whereas MCF7 cells formed smooth surfaces. Moreover, when heterogeneous tumoroids were placed onto collagen gels, highly invasive MDAMB231 cell-rich surface regions produced extensions into the matrix, whereas poorly invasive MCF7 cells did not. The fact that one can form a large number of 1-mm tumoroids in 1 coculture attests to the potential use of this system at high-throughput investigations of cancer drug development and drug delivery into the tumor.

Breast Neoplasms↗

PubMed2006

Porogen-based solid freeform fabrication of polycaprolactone-calcium phosphate scaffolds for tissue engineering.

Drop on demand printing (DDP) is a solid freeform fabrication (SFF) technique capable of generating microscale physical features required for tissue engineering scaffolds. Here, we report results toward the development of a reproducible manufacturing process for tissue engineering scaffolds based on injectable porogens fabricated by DDP. Thermoplastic porogens were designed using Pro/Engineer and fabricated with a commercially available DDP machine. Scaffolds composed of either pure polycaprolactone (PCL) or homogeneous composites of PCL and calcium phosphate (CaP, 10% or 20% w/w) were subsequently fabricated by injection molding of molten polymer-ceramic composites, followed by porogen dissolution with ethanol. Scaffold pore sizes, as small as 200 microm, were attainable using the indirect (porogen-based) method. Scaffold structure and porosity were analyzed by scanning electron microscopy (SEM) and microcomputed tomography, respectively. We characterized the compressive strength of 90:10 and 80:20 PCL-CaP composite materials (19.5+/-1.4 and 24.8+/-1.3 Mpa, respectively) according to ASTM standards, as well as pure PCL scaffolds (2.77+/-0.26 MPa) fabricated using our process. Human embryonic palatal mesenchymal (HEPM) cells attached and proliferated on all scaffolds, as evidenced by fluorescent nuclear staining with Hoechst 33258 and the Alamar Blue assay, with increased proliferation observed on 80:20 PCL-CaP scaffolds. SEM revealed multilayer assembly of HEPM cells on 80:20 PCL-CaP composite, but not pure PCL, scaffolds. In summary, we have developed an SFF-based injection molding process for the fabrication of PCL and PCL-CaP scaffolds that display in vitro cytocompatibility and suitable mechanical properties for hard tissue repair.

Calcium Phosphates↗

PubMed2006

Engineering three-dimensional pulmonary tissue constructs.

In this paper, we report on engineering 3-D pulmonary tissue constructs in vitro. Primary isolates of murine embryonic day 18 fetal pulmonary cells (FPC) were comprised of a mixed population of epithelial, mesenchymal, and endothelial cells as assessed by immunohistochemistry and RT-PCR of 2-D cultures. The alveolar type II (AE2) cell phenotype in 2-D and 3-D cultures was confirmed by detection of SpC gene expression and presence of the gene product prosurfactant protein C. Three-dimensional constructs of FPC were generated utilizing Matrigel hydrogel and synthetic polymer scaffolds of poly-lactic-co-glycolic acid (PLGA) and poly-L-lactic-acid (PLLA) fabricated into porous foams and nanofibrous matrices, respectively. Three-dimensional Matrigel constructs contained alveolar forming units (AFU) comprised of cells displaying AE2 cellular ultrastructure while expressing the SpC gene and gene product. The addition of tissue-specific growth factors induced formation of branching, sacculated epithelial structures reminiscent of the distal lung architecture. Importantly, 3-D culture was necessary for inducing expression of the morphogenesis-associated distal epithelial gene fibroblast growth factor receptor 2 (FGFr2). PLGA foams and PLLA nanofiber scaffolds facilitated ingrowth of FPC, as evidenced by histology. However, these matrices did not support the survival of distal lung epithelial cells, despite the presence of tissue-specific growth factors. Our results may provide the first step on the long road toward engineering distal pulmonary tissue for augmenting and/or replacing dysfunctional native lung in diseases, such as neonatal pulmonary hypoplasia.

Animals↗

PubMed2005

Electrospun protein fibers as matrices for tissue engineering.

Electrospinning has recently emerged as a leading technique for generating biomimetic scaffolds made of synthetic and natural polymers for tissue engineering applications. In this study, we compared collagen, gelatin (denatured collagen), solubilized alpha-elastin, and, as a first, recombinant human tropoelastin as biopolymeric materials for fabricating tissue engineered scaffolds by electrospinning. In extending previous studies, we optimized the shape and size (diameter or width) of the ensuing electrospun fibers by varying important parameters of the electrospinning process, such as solute concentration and delivery rate of the polymers. Our results indicate that the average diameter of gelatin and collagen fibers could be scaled down to 200-500 nm without any beads, while the alpha-elastin and tropoelastin fibers were several microns in width. Importantly, and contrary to any hitherto reported structures of electrospun polymers, fibers composed of alpha-elastin, especially tropoelastin, exhibited "quasi-elastic" wave-like patterns at increased solution delivery rates. The periodicity of these wave-like tropoelastin fibers was partly affected by the delivery rate. Atomic force microscopy was utilized to profile the topography of individual electrospun fibers and microtensile testing was performed to measure their mechanical properties. Cell culture studies confirmed that the electrospun engineered protein scaffolds support attachment and growth of human embryonic palatal mesenchymal (HEPM) cells.

Animals↗