Search PubMed⌕ Search

Biomedical subjects

L Z Luo

Publications and source records attributed to L Z Luo.

13 recordsLinked to original sources

The study of new calibration features in the Harshaw TLD system.

The Harshaw TLD system has three key calibration procedures: the Reader, the Dosemeter and the Algorithm. These functions must be properly calibrated for the system to achieve the optimum results. For the conventional reader and dosemeter calibration, Harshaw TLD recommends a pre-fade and a post-fade of 24-48 h when calibrating the system for LiF:Mg,Ti type dosemeter. It is also recommended that keeping the fade time consistent is important to maintain the quality of the system performance. In recent years, new calibration features have been introduced into the Harshaw TLD models 6600 and 8800 operating systems. These new features are Auto Calibration, Auto QC and Auto Blank, and they give the user the ability to set up the clear-expose-read process to be performed automatically in a sequence for each dosemeter. This saves processing time and keeps the fade time the same. However, since the fade time is near zero, will it affect the TLD system calibration factors? What should the user expect? This paper presents a study of the effect of Auto Calibration/Auto QC to the TLD operation.

Body Burden↗

Type testing of an extremity finger stall dosemeter based on Harshaw TLD EXTRAD technology.

A new type of extremity dosemeter, which incorporates the Harshaw TLD EXTRAD dosemeter element into a PVC finger stall, has been developed. The dosemeter uses high-sensitivity lithium fluoride, (7)LiF:Mg,Cu,P (TLD-700H) in a thin 7 mg cm(-2) layer, with alternative coverings of PVC at 10 mg cm(-2) and aluminised polyester at 3.2 mg cm(-2). Results are presented of the type testing of both versions of the finger stall dosemeter against published standards.

Dose-Response Relationship, Radiation↗

The application of LiF:Mg,Cu,P to large scale personnel dosimetry: current status and future directions.

LiF:Mg,Cu,P is starting to replace LiF:Mg,Ti in a variety of personnel dosimetry applications. LiF:Mg,Cu,P has superior characteristics as compared to LiF:Mg,Ti including, higher sensitivity, improved energy response for photons, lack of supralinearity and insignificant fading. The use of LiF:Mg,Cu,P in large scale dosimetry programs is of particular interest due to the extreme sensitivity of this material to the maximum readout temperature, and the variety of different dosimetry aspects and details that must be considered for a successful implementation in routine dosimetry. Here we discuss and explain the various aspects of large scale LiF:Mg,Cu,P based dosimetry programs including the properties of the TL material, new generation of TLD readers, calibration methodologies, a new generation of dose calculation algorithms based on the use of artificial neural networks and the overall uncertainty of the dose measurement. The United States Navy (USN) will be the first US dosimetry processor who will use this new material for routine applications. Until June 2002, the Navy used two types of thermoluminescent materials for personnel dosimetry, CaF2:Mn and LiF:Mg,Ti. A program to upgrade the system and to implement LiF:Mg,Cu,P, started in the mid 1990s and was recently concluded. In 2002, the new system replaced the LiF:Mg,Ti and is scheduled to start replacing the CaF2:Mn system in 2006. A pilot study to determine the dosimetric performance of the new LiF:Mg,Cu,P based dosimetry system was recently completed, and the results show the new system to be as good or better than the current system in all areas tested. As a result, LiF:Mg,Cu,P is scheduled to become the primary personnel dosimeter for the entire US Navy in 2006.

Copper↗

Type testing the Model 6600 plus automatic TLD reader.

The Harshaw Model 6600 Plus is a reader with a capacity for 200 TLD cards or 800 extremity cards. The new unit integrates more functionality, and significantly automates the QC and calibration process compared to the Model 6600. The Model 6600 Plus was tested against the IEC 61066 (1991-2012) procedures using Harshaw TLD-700H and TLD-600H, LiF:Mg,Cu,P based TLD Cards. An overview of the type testing procedures is presented. These include batch homogeneity, detection threshold, reproducibility, linearity, self-irradiation, residue, light effects on dosemeter, light leakage to reader, voltage and frequency, dropping and reader stability. The new TLD reader was found to meet all the IEC criteria by large margins and appears well suited for whole body, extremity and environmental dosimetry applications, with a high degree of dosimetric performance.

Equipment Design↗

Performance of Harshaw TLD-100H two-element Dosemeter.

One of the advantages of LiF based thermoluminescent (TL) materials is its tissue-equivalent property. The Harshaw TLD-100H (LiF:Mg,Cu,P) material has demonstrated that it has a near-flat photon energy response and high sensitivity. With the optimized dosemeter filters built into the holder, the Harshaw TLD-100H two-element dosemeter can be used as a whole body personnel dosemeter for gamma, X ray and beta monitoring without the use of an algorithm or correction factor. This paper presents the dose performance of the Harshaw TLD-100H two-element dosemeter against the ANSI N13.11-2001 standard and the results of tests that are required in IEC 1066 International Standard.

Dose-Response Relationship, Radiation↗

The dose-response of Harshaw TLD-700H.

Harshaw TLD-700H (7LiF:Mg,Cu,P) was previously characterised for low- to high-dose ranges from 1 microGy to 20 Gy. This paper describes the studies and results of dose-response and linearity at much higher doses. TLD-700H is a near perfect dosimetric material with near tissue equivalence, flat energy response, and the ability to measure beta, gamma and X rays. These new results extend the applicability of Harshaw TLD-700H into more dosimetric measurement environments. The simple glow curve structure provides insignificant fade, eliminating special oven preparation methods experienced by other materials. The work presented in this paper quantifies the performance of Harshaw TLD-700H in extended ranges.

Computer Simulation↗

LiF:Mg,Cu,P glow curve shape dependence on heating rate.

The glow curve shape of LiF:Mg,Cu,P (MCP) material is studied in this research. The study is focused on the effects of the heating rate on the dosimetric peaks. Different configurations of dosemeters (chips, cards and powder) are studied. The shifting of the dominant dosimetric peak is observed and analysed. The curves are deconvoluted using the new Harshaw Glow Curve Analyser (GCA) program. Results of the study are presented, as well as possible explanations as to the observed effects.

Computer Simulation↗

Evaluating two extremity dosemeters based on LiF:Mg,Ti or LiF:Mg,Cu,P.

Evaluation of a new extremity dosemeter is presented. The dosemeter is a passive device that is easy to wear and features a permanent individual numerical ID with barcode, a watertight case, an automatic TLD reader and database management software. Two dosemeters were studied: the first consists of a 100 mg x cm(-2) 7LiF:Mg,Ti (TLD-700) chip and a 42 mg x cm(-2) cap, the other consists of a 7 mg x cm(-2) layer of 7LiF:Mg,Cu,P (TLD-700H) powder and a 5 mg x cm(-2) cap. Sensitivity, repeatability, lower limit detection, angular responses and energy responses for these dosemeters are studied and presented. The dose calculation algorithm is developed and its dosimetric performance accuracy is compared with the standard ANSI N13.32-1995, Performance Testing of Extremity Dosemeters.

Beta Particles↗

Spontaneous mutations leading to antigenic variations in the glycoproteins of vesicular stomatitis virus field isolates.

Strains of vesicular stomatitis virus, New Jersey serotype (VSV-NJ), isolated from diseased cattle or swine were examined by genomic RNA sequencing for genetic diversity potentially leading to antigenic variations in their type-specific glycoproteins as determined by reactivity with epitope-specific monoclonal antibodies (MAbs). Seven field isolates recovered in Colorado, New Mexico, Georgia, and Mexico during the widespread 1982-1985 epizootic in the western United States resembled the prototypic 1952 Hazelhurst subtype by partial sequence homology, but amino acid reversions to the 1949 Ogden subtype occurred frequently. When studies were performed with MAbs directed to the Ogden subtype glycoprotein, relatively limited antigenic variation, and only in neutralization epitope VIII, was noted among two of five epizootic isolates from Colorado and New Mexico. However, amino acid differences in the glycoprotein of a 1983 isolate from an enzootic region of Georgia resulted in major antigenic deficiencies in epitopes V, VI, and VII as determined by Western blotting and neutralization of infectivity with epitope-specific MAbs. Quite a few genetic but no antigenic differences were noted in an enzootic 1984 isolate from Mexico, a potential origin of the United States epizootic. Marked or complete loss of epitopes VII, VI, VIII, and V can be traced to spontaneous mutations leading to amino acid substitutions at glycoprotein positions 199, 263, 275, and 317, respectively, in the enzootic Georgia isolate 07/83-GA-P and the epizootic New Mexico isolate 06/85-NM-B. By comparison, closely adjacent amino acid substitutions at glycoprotein positions 210, 268, 277, and 364 occurred in epitope-deficient mutants selected for resistance to neutralization by MAbs specific for epitopes VII, VI, VIII, and V, respectively. Two neutralization epitopes designated X and XI were found to be unique for the G protein of the 1952 Hazelhurst isolate..../52-GA-P. The epitope X-specific MAb H21, in particular, failed to neutralize the infectivity not only of the Ogden subtype..../49-UT-B but also was ineffective against all the 1982-1985 field isolates. The classical 1952 Hazelhurst strain of VSV-NJ is genetically and antigenically quite different from those viruses isolated during the 1982-1985 epizootic.

Amino Acid Sequence↗

Transcription inhibition site on the M protein of vesicular stomatitis virus located by marker rescue of mutant tsO23(III) with M-gene expression vectors.

The matrix (M) protein of vesicular stomatitis virus serves as an endogenous inhibitor of viral transcription, a function missing or deficient in M proteins of temperature-sensitive (ts) mutants assigned to complementation group III. Previous studies with mutant tsO23(III) and vaccinia virus M-gene expression vectors revealed that the temperature-sensitive phenotype is due to a mutation leading to substitution of phenylalanine for leucine at amino acid III, whereas loss of the major antigenic determinant (epitope 1) of the mutant M protein results from the substitution of glutamic acid for the wild-type amino acid glycine at position 21 (Y. Li, L. Luo, R. M. Snyder, and R. R. Wagner, J. Virol. 62:3729-3737, 1988). We demonstrate here that transcription inhibition activity is restored to rescued tsO23 virus only when the rescuing vaccinia virus recombinant expresses M protein with glycine and not glutamic acid at amino acid 21. These experiments indicate the importance of the conformational integrity of the amino-terminal domain in determining the capacity of the vesicular stomatitis virus M protein to down regulate endogenous transcription.

Blotting, Western↗

Site-specific mutations in vectors that express antigenic and temperature-sensitive phenotypes of the M gene of vesicular stomatitis virus.

Full-length cDNA copies of mRNAs coding for the matrix (M) proteins of vesicular stomatitis virus and its mutant tsO23(III) were cloned in pBSM13- (BlueScribe). The authenticity of these clones was demonstrated by restriction enzyme mapping, DNA sequencing, and in vitro transcription and translation to identify the two M proteins by Western immunoblotting with epitope-specific monoclonal antibodies. Site-directed mutants were constructed by primer extension of synthetic oligodeoxynucleotides with one or two nucleotide changes to alter the glycine at amino acid 21 of the wild-type (wt) M gene to glutamic acid, alanine, or proline. Similarly, a revertant was created in the M gene of mutant tsO23 by a Glu-21----Gly substitution. A series of wt- and mutant-M-gene chimeras was also constructed to create mutant and revertant clones with Leu----Phe and His----Tyr alterations at amino acids 111 and 227, respectively. We then moved the wt and tsO23 M genes and their site-specific mutants and chimeras cloned in pBSM13- into the eucaryotic expression vector pTF7 directed by the T7 bacteriophage RNA polymerase of the vaccinia virus recombinant vTF1-6,2. Western blot analysis of the M proteins transiently expressed in CV-1 cells by plasmids carrying M genes altered at amino acid 21 revealed that the critical antigenic determinant (epitope 1) is expressed only by the Gly-21 M protein and not by Glu-21, Ala-21, or Pro-21 M proteins. Of particular interest is an apparent conformational change, evidenced by slightly but significantly retarded electrophoretic migration, in plasmid-expressed M proteins with amino acids substituted for glycine at position 21. The glutamic acid at position 21 of tsO23 is not responsible for its temperature-sensitive phenotype, because a tsO23 revertant plasmid with glycine substituted at position 21 fails to rescue tsO23 virus in cells infected at the restrictive temperature; conversely, plasmids expressing wt M protein with substitutions of glutamic acid, alanine, or proline at position 21 are just as effective in marker rescue of tsO23 as is the Gly-21 wt M protein. Marker rescue experiments with wt- and mutant-M-gene chimeras support the hypothesis of K. Morita, R. Vanderoef, and J. Lenard (J. Virol. 61:256-263, 1987) that the temperature-sensitive phenotype of tsO23 is due to a phenylalanine substituted for leucine at amino acid 111, rather than the His-227----Tyr substitution or the Gly-21----Glu substitution, which independently accounts for the loss of epitope 1 in the mutant M protein of tsO23.(ABSTRACT TRUNCATED AT 400 WORDS)

Animals↗

Expression of the M gene of vesicular stomatitis virus cloned in various vaccinia virus vectors.

Initial attempts to clone the matrix (M) gene of vesicular stomatitis virus (VSV) in a vaccinia virus expression vector failed, apparently because the expressed M protein, and particularly a carboxy-terminus-distal two-thirds fragment, was lethal for the virus recombinant. Therefore, a transient eucaryotic expression system was used in which a cDNA clone of the VSV M protein mRNA was inserted into a region of plasmid pTF7 flanked by the promoter and terminator sequences for the T7 bacteriophage RNA polymerase. When CV-1 cells infected with recombinant vaccinia virus vTF1-6,2 expressing the T7 RNA polymerase were transfected with pTF7-M3, the cells produced considerable amounts of M protein reactive by Western blot (immunoblot) analysis with monoclonal antibodies directed to VSV M protein. Evidence for biological activity of the plasmid-expressed wild-type M protein was provided by marker rescue of the M gene temperature-sensitive mutant tsO23(III) at the restrictive temperature. Somewhat higher levels of M protein expression were obtained in CV-1 cells coinfected with a vaccinia virus-M gene recombinant under control of the T7 polymerase promoter along with T7 polymerase-expressing vaccinia virus vTF1-6,2.

Genes, Viral↗