Biomedical subjects

L W Whitehead

Publications and source records attributed to L W Whitehead.

6 recordsLinked to original sources

PubMed1988

The influence of task and location on solvent exposures in a printing plant.

A work measurement technique was used to monitor the activities of seven printing press operators. Repeated observations were made to learn workers' tasks and workers' locations in the plant, and a photoionization detector was used to measure the instantaneous solvent concentration in each worker's breathing zone. Location data, analyzed using a computer aided design system, did not show any indication that there were high or low exposure areas. Regression, however, showed that a significant amount of variability in a worker's exposures was accounted for by the number of times the worker performed a certain "hazardous task" (r2 = 0.57). The results indicate that it may be possible to simplify industrial hygiene sampling strategies by using work measurement data, such as time study or work sampling, to identify maximum risk employees.

Air Pollutants, Occupational↗

PubMed1987

Respiratory symptoms associated with the use of azodicarbonamide foaming agent in a plastics injection molding facility.

Respiratory health variables were studied cross-sectionally in 227 employees of a plastics molding facility where numerous complaints had been apparently associated with the use of azodicarbonamide foaming agent in injection molding. Pre- and postshift respiratory status measures and azodicarbonamide concentrations were also obtained for 17 employees. Cross-sectional pulmonary function differences by injection molding status were not observed. Modest decrements in pulmonary function measures were observed between start and end of shift but with no dose-effect relationship. A strong association was observed for injection molding workers for eye/nose/throat irritation, cough, and wheezing. Additionally, wheezing, chest tightness, and symptoms of chronic bronchitis were strongly associated with work in injection molding during periods in which azodicarbonamide was in use. These results suggest respiratory symptom causation by some combination of azodicarbonamide itself, reaction products of azodicarbonamide formed during injection molding, or other unidentified agents uniquely associated with the process of injection molding with azodicarbonamide foaming agent.

Adult↗

PubMed1985

Computerized spirometry using a portable microcomputer.

The reliable conduct of pulmonary function studies, while in the field, is increasingly important as various standards mandate this activity. Versatile, portable and accurate equipment is required. A lightweight and computerized portable spirometer system is discussed, PSPIRO, which uses a standard volumetric spirometer and a briefcase-sized microcomputer. The system, compact enough to be easily moveable by one person, performs tests for FVC, FEV(1), FEV(3), the percentage of predicted pulmonary function for each, and the ratio of FEV(1)/FVC. Back extrapolation is used to establish the start of each forced expiratory maneuver, reproducibility checks are performed, and accuracy is within acceptable epidemiologic standards. A small, portable analog to digital interface (PLAD) was developed for performing A/D conversions through the RS-232C port of the portable microcomputer.

Humans↗

PubMed1985

Behavioural evaluation of workers exposed to mixtures of organic solvents.

Reports from Scandinavia have suggested behavioural impairment among long term workers exposed to solvents below regulatory standards. A cross sectional study of behavioural performance was conducted among printers and spray painters exposed to mixtures of organic solvents to replicate the Scandinavian studies and to examine dose-response relationships. Eligible subjects consisted of 640 hourly workers from four midwestern United States companies. Of these, 269 responded to requests to participate and 240 were selected for study based on restrictions for age, sex, education, and other potentially confounding variables. The subjects tested had been employed on average for six years. Each subject completed an occupational history, underwent a medical examination, and completed a battery of behavioural tests. These included the Fitts law psychomotor task, the Stroop colour-word test, the Sternberg short term memory scanning test, the short term memory span test, and the continuous recognition memory test. Solvent exposure for each subject was defined as an exposed or non-exposed category based on a plant industrial hygiene walk-through and the concentration of solvents based on an analysis of full shift personal air samples by gas chromatography. The first definition was used to maintain consistency with Scandinavian studies, but the second was considered to be more accurate. The average full shift solvent concentration was 302 ppm for the printing plant workers and 6-13 ppm for the workers at other plants. Isopropanol and hexane were the major components, compared with toluene in Scandinavian studies. Performance on behavioural tests was analysed using multiple linear regression with solvent concentration as an independent variable. Other relevant demographic variables were also considered for inclusion. No significant (p greater than 0.05) relation between solvent concentration and impairment on any of the 10 behavioural variables was observed after controlling for confounding variables. Exposed/non-exposed comparisons showed a significantly poorer digit span among those exposed, but this has not been generally reported in the Scandinavian studies. The medical examination showed no abnormalities of clinical significance. The inability to replicate the findings of the Scandinavian studies could have been due to the shortness of the duration of workers' exposure, the type of solvents in the mixtures, use of different behavioural tests, or to selection factors.

Adult↗

PubMed1974

Disinfection.

Explore the source record for details and available documents.

Chlorine↗

PubMedDate not supplied

Potential exposure to metal fumes, particulates, and organic vapors during radiotherapy shielding block fabrication.

The shielding-block fabrication areas of three hospitals were surveyed to assess inhalation exposure to lead (Pb), cadmium (Cd), bismuth (Bi), and tin (Sn) fumes, as well as styrene and methyl chloride vapors. Area and personal breathing zone samples were collected for various steps in the block fabrication process. Only 3 of 16 air samples for metals resulted in detectable levels of Pb and/or Cd. The levels were well below the Occupational Safety and Health Administration (OSHA) Permissible Exposure Limits, excluding a sample which contained a visible metal fragment. Bi and Sn were not detected in any samples. Methyl chloride and styrene vapors were not detected in any air samples during foam cutting procedures. Total particulates (TP) were measurable in 11 of 17 air samples (ranging from 0.01 to 2.1 mg/m3). TP values were below the OSHA federal standard for nuisance particulates, which is 15 mg/m3. The data suggest that the materials and procedures sampled do not present an inhalation hazard to employees who construct shielding blocks. Precautions should, however, be exercised to prevent exposure under extreme procedural conditions such as soldering or overheating of alloy, and by other means such as ingestion. Care should also be taken during cleanup or housekeeping to prevent re-entrainment into the work atmosphere of mechanically generated metal particles or materials condensed within melting pots (which may be high in metal content).

Air Pollutants, Occupational↗