Biomedical subjects

L G Ullate

Publications and source records attributed to L G Ullate.

4 recordsLinked to original sources

PubMed2002

3D beamforming with ultrasonic divided-ring arrays.

Conventional 2D arrays have a set of squared elements whose inter-element spacing is around lambda/2. This arrangement requires an excessive amount of electronic resources for the generation and processing of ultrasonic signals. In this work, the beam properties of a single divided-ring array are analysed theoretically with the goal of producing volumetric images. Divided-ring arrays are based on a circular pattern, which has a lower periodicity than square arrays, and this property allows increasing the element size while keeping the amplitude of the grating lobes at a reasonably low level. The paper emphasises several advantages of ring arrays, suggesting that these apertures are useful for 3D ultrasonic imaging. First, as the element size may increase, the number of elements can be reduced with little loss of emitting area. Second, ring arrays produce beams of large depth of field in both transmission and reception. This can be used to avoid the complexity associated with dynamic focusing.

Models, Theoretical↗

PubMed2002

64 elements two-dimensional piezoelectric array for 3D imaging.

Ultrasound has a large potential on non-invasive inspection with main applications in medical imaging and non-destructive testing (NDT). The increasing interest in 3D imaging applications leads to investigate new solutions for two-dimensional (2D) ultrasonic arrays with an affordable number of electronic channels without resolution degradation. 2D segmented annular arrays (SAAs) are a good compromise between resolution--image quality--and number of electronically active channels. A 1-3 piezoelectric composites are used as basis material to manufacture the array transducers due to their low planar coupling and high electromechanical coupling coefficients. A 1.5 MHz SAA of 64 elements and 20 mm of diameter was designed, manufactured and tested. The design key point is the use of a flexible circuit with electrodes and tracks that define the array geometry. The piezocomposite was used as a monolithic support. Soft backing and one matching layer were used. The array elements have been tested electrically and acoustically showing good agreement with a KLM-based simulation model. Acoustical field measurements in water at different steering angles were made and compared with simulations performed with a model that uses an exact solution of the impulse response approach. Side lobes are important because the array geometry used was designed to work in metals for NDT purposes. Smaller array elements should be made for medical applications.

Imaging, Three-Dimensional↗

PubMed2002

Application of micromechanics to the characterization of mortar by ultrasound.

Mechanical properties of concrete and mortar structures can be estimated by ultrasonic non-destructive testing. When the ultrasonic velocity is known, there are standardized methods based on considering the concrete a homogeneous material. Cement composites, however, are heterogeneous and porous, and have a negative effect on the mechanical properties of structures. This work studies the impact of porosity on mechanical properties by considering concrete a multiphase material. A micromechanical model is applied in which the material is considered to consist of two phases: a solid matrix and pores. From this method, a set of expressions is obtained that relates the acoustic velocity and Young's modulus of mortar. Experimental work is based on non-destructive and destructive procedures over mortar samples whose porosity is varied. A comparison is drawn between micromechanical and standard methods, showing positive results for the method here proposed.

Journal Article↗

PubMed2002

Time-frequency Wiener filtering for structural noise reduction.

In order to enhance the defect in relation to background noise of large grained materials different algorithms have been developed. Wiener filtering techniques have proved to be efficient for the SNR enhancement of ultrasonic signals coming from highly scattering materials. These processing algorithms are based on designing a filter that has large gain at frequencies where the SNR is high and low gain at frequencies where SNR is small. However, this technique does not consider two important ultrasonic effects: the finite-time duration of the flaw UT signal coming from a defect and the distortion of the frequency components of the traveling wave-front due to the dispersion. In this work, a time-frequency Wiener filter is proposed that takes into account these two characteristics. Experimental results are presented, showing that the proposed time-frequency algorithm has an excellent performance on SNR enhancement.

Journal Article↗