Search PubMed⌕ Search

Biomedical subjects

L Di Palma

Publications and source records attributed to L Di Palma.

At least 19 recordsLinked to original sources

Use of EAF dust as heterogeneous catalyst in Fenton oxidation of PCP contaminated wastewaters.

In this study, chemical oxidation tests using H2O2 were performed on a solution contaminated with 100 mg l(-1) of pentachlorophenol (PCP). The effectiveness of electric arc furnace dust and hematite as heterogeneous catalysts was evaluated. Reactions were conducted at pH 2 for 24 h. Either H2O2 stabilized with KH2PO4 or un-stabilized H2O2 was used. Total organic carbon (T.O.C.) removal and chloride release from PCP molecule were monitored. Results showed that the maximum removal yields for electric arc furnace (EAF) dust (49.2% T.O.C., 56.7% Cl) were achieved when H2O2:PCP ratio was 10:1 and Fe:H2O2 = 1:5 for unstabilized H2O2 and when H2O2:PCP = 10:1 and Fe:H2O2 = 1:1 for stabilized H2O2 (48% T.O.C., 60.6% Cl). The maximum yield using hematite (45.2% T.O.C., 55.2% Cl) was obtained when H2O2:PCP ratio was 10:1 and Fe:H2O2 was 1:2. When EAF dust was used and Fe:H2O2 > 1:5, Cl release was higher than the one expected from T.O.C. removal.

Catalysis↗

Heavy metals extraction from contaminated soil: recovery of the flushing solution.

The optimum conditions for the recovery of copper from a contaminated soil by using the soil flushing technique are evaluated. Tests on a soil artificially contaminated with copper chloride were carried out in order to evaluate the influence of the speed of percolation and of the chelating agent concentration (aqueous solution of an ethylendiaminotetraacetic acid di-sodium salt Na2-EDTA). At pH=7.3 an efficiency up to 93.9% for copper extraction was achieved by flushing 500 ml of Na2-EDTA 0.05 M solution and 100 ml of pure water at 0.792 cm/h. At these operating conditions the formation of EDTA complexes with other competitive cations (calcium and iron) was negligible. The experimental results were in agreement with the ones obtained using a model describing the chemistry of metal extraction. This model assessed that above pH=6 the formation of calcium and iron EDTA complexes was excluded and only the chelation of copper was allowed. The recovery of 91.6% of EDTA was also achieved by evaporating and acidifying the extracted solution: after filtration, solid EDTA was obtained, through the addition of sodium hydroxide Na2-EDTA. About 99.5% of the extracted copper was finally precipitated under alkaline conditions from the liquid phase.

Chelating Agents↗

Copper leaching from a sandy soil: mechanism and parameters affecting EDTA extraction.

A series of 24h batch tests of copper extraction from a sandy soil were performed by washing the soil with aqueous solution of ethylenediaminetetraacetic acid, EDTA. EDTA versus copper molar ratio were in the range between 1 (equimolar tests) and 13.3. The tests were performed at three selected liquid/solid ratio, 5, 12.5 and 25. Results show that decreasing the pH of the washing solution an higher copper extraction yield was achieved: an almost complete copper extraction was achieved after 23 h of mixing at a L/S = 5, and after 5 h of mixing at an L/S = 12.5. The mechanism of copper extraction was found to involve two sequential processes: the former dissolution of metal salts, that lead to an initial high concentration of both copper and some competitive cations (essentially Ca(2+)), and the following EDTA exchange reaction between calcium and copper complexes, which corresponded an increase of pH in the washing solution. A negligible extraction of Fe(3+) was also observed at the investigated operative conditions.

Chelating Agents↗

Experimental evaluation of inhibition effects of saline wastewater on activated sludge.

Industrial wastewater often has a high salt content, due to specific factories and to the use of seawater in coastal areas. Once it has reached the activated sludge treatment, saline wastewater may cause biomass inhibition and dramatic loss in purification efficiency. In the present work, the inhibiting effect of saline influent was experimentally evaluated through respirometric tests on samples of the incoming wastewater. Activated sludge was grown in bench-scale continuous flow stirred tank reactor (CFSTR), supplied with synthetic wastewater. Synthetic saline wastewater was prepared using sodium chloride and sodium sulphate at different concentrations. Samples of mixed liquor were drawn from the CFSTR reactor and fed with saline wastewater in shock-load or in continuous mode, then respiration activity and carbon removal yield were evaluated. In batch mode (shock-load), salt/biomass ratios between 0.37 and 30.7 gsalt gvss(-1) gave respiration inhibition between 4% and 84% respectively. The respirometry bioassay required a short response time and the values of respiration inhibition predicted the loss in carbon removal efficiency with a good accuracy. In continuous mode, for salt/biomass ratio of 35.5 gsaltgvss(-1), respiration inhibition of 81% was obtained. This work showed that a relation between inhibition in shock-load and inhibition in continuous mode can be determined, therefore, the procedure herein proposed allows performing offline bioassays on real biological plants, to assess in real time the inhibiting effect of the incoming wastewater before it reaches the activated sludge reactor.

Biological Assay↗

EDTA leaching of copper from contaminated soils: experimental study and transport model application for parameters estimation.

EDTA column's extraction were performed on four artificially contaminated soils, followed by the percolation of pure water to ensure the removal of EDTA entrapped in soil. The investigated soils were characterized by a content of organic matter ranging from 1% to 25%. A mathematical model was developed for copper leaching from the soils. The correlation of experimental data shows that while the EDTA transport was not affected by the soil organic fraction, the simulated transport of Cu-EDTA complexes in solution exhibited a delay effect due to the chemical adsorption of such complexes onto the soil organic matter. The distribution coefficient (Kd), between the solid and liquid phases showed a logarithmic increase when the organic content of soil increased. The column's hydrodynamic characteristics (alphaL) and the kinetic coefficients (k) of chelant extraction were estimated independently for each soil. A correlation of kinetic coefficients data versus soil's organic content was also proposed: experimental data showed, in the investigated range, a logarithmic dependence of k on the organic content of soil.

Chelating Agents↗

Experimental assessment of the operative conditions of copper extraction from three contaminated soils.

Column experiments of EDTA extraction of copper from a sandy, a calcareous, and a highly organic soil, were performed. The influence of EDTA concentration, pH, and the flow rate of a flushing solution on copper extraction yield was investigated. Extraction yields of 84.8%, 93.0% and 96.9% were achieved respectively for sandy soil, calcareous soil and highly organic soil, after the injection of a volume of flushing solution equal to 15 pore volumes. TOC measurements performed on the extracted solution showed that, after the extraction phase, the percolation of an equal volume of water was necessary to ensure complete EDTA removal from the treated soils. In addition, results showed that the simultaneous dissolution of calcite consumed approximately 93.6% of the chelant agent when EDTA concentration in the flushing solution was 0.05 M.

Chelating Agents↗

Effect of ethanol on the oxidation of atrazine in the remediation of contaminated soil.

The oxidation of an atrazine solution obtained from a flushing treatment of a contaminated soil was investigated. Experimental tests were performed on an artificially contaminated standard soil. Atrazine was removed from the soil by flushing with an aqueous solution at 5% volume of ethanol. Oxidative Fenton-type treatment on the extracted solution was then performed in order to transform atrazine into its by-products. The influence of different concentration of ethanol on atrazine oxidation was studied. Results show that the oxidative treatment is strongly affected by the ethanol residual amount. The degradation mechanism of atrazine during oxidation with Fenton's reagent in the presence of ethanol was also investigated.

Atrazine↗

Recovery of EDTA and metal precipitation from soil flushing solutions.

This work studies the effectiveness of a process proposed for the recovery of ethylenediaminetetraacetic acid (EDTA) and metal precipitation from soil flushing solutions. Two series of experimental tests were carried out on two samples of a soil artificially contaminated with copper or lead. The metals were extracted from the soil by flushing with a 0.05 M aqueous solution of EDTA sodium salt (E-Na(2)). Cu or Pb extraction efficiencies of about 95 and 98% were observed, respectively. The two extracted solutions were then treated to obtain EDTA recovery and metal precipitation from the aqueous solution. EDTA recovery was achieved in two steps. An initial evaporation treatment lead to reduce the solution volume by about 75%. This was followed by the acidification of the residue solution, which precipitated more than 93% of the used EDTA. The precipitated EDTA was removed by filtration, and was suitable for reuse after adding an alkaline agent. Metal precipitation from the filtered solution was performed using two different methods: an almost total (99.5%) Pb precipitation in alkaline conditions was achieved after complex destabilization through the sequential addition of ferric ions and sodium phosphate, while 93.6% copper precipitation was achieved with ferrous sulfate as a destabilization agent.

Chelating Agents↗

Experimental study of the remediation of atrazine contaminated soils through soil extraction and subsequent peroxidation.

This paper presents a feasibility study in the field of the remediation of soils contaminated with atrazine. Experimental tests were performed on an artificially contaminated synthetic soil. Atrazine was removed from the soil by flushing with an aqueous solution at 5 vol.% of ethanol. Experimental tests of evaporation and Fenton's oxidation on the extracted solution were then performed in order to transform atrazine into its oxidation products. Tests were performed in the presence of a peroxide excess the ratio between Fe(2+) and H(2)O(2) was 1:10. Peroxide was first added in order to reduce the consumption of hydroxyl radicals by their reaction with the excess of Fe(2+). The degradation mechanism of atrazine during oxidation with Fenton's reagent in the presence of ethanol was investigated. Results showed that due to the non selective nature of Fenton's reagent a high consumption of reagent was needed to achieve a significant atrazine oxidation from solutions at 4.5 vol.% of ethanol. While at a Fe(2+) concentration of 3mM atrazine practically disappeared from pure aqueous solutions within 2h, a degradation yield of only 28.1% was observed in the presence of ethanol even when Fe(2+) concentration was 15 mM.

Atrazine↗

A steady-state model for the evaluation of disk rotational speed influence on RBC kinetic: model presentation.

The physical and biological mechanisms of attached-biomass growth were analyzed and a steady-state model was proposed to determine the soluble carbonaceous removal in an RBC unit for different organic loading rates in the reactor. The objective of the model was the prediction of the organic loading rate corresponding to the maximum removal capacity in the system. A system of equations was solved where the influent soluble carbonaceous substrate concentration was the main variable. Monod's rate law was used for the growth of microorganism: the soluble carbonaceous substrate was the limiting substrate. Endogenous decay was neglected. The influence of disk rotational speed on the RBC removal capacity was investigated, the disk rotational speed being a parameter acting on oxygen transfer in the biofilm. The criteria for the evaluation of the kinetic parameter in the model were proposed.

Bacteria↗

Assessment of the leaching of metallic elements in the technology of solidification in aqueous solution.

Results are presented of experiments performed to optimize the solidification/stabilization system for metallic elements in aqueous solution. This system involves mixing cement and a solution of metallic elements in a conventional mixer: the paste thus obtained is transferred drop by drop into a recipient filled with an aqueous solution of NaOH at 20% by weight, in which it solidifies immediately. The separate use of chloride solutions of Li+, Cr3+, Pb2+ and Zn2+ makes it possible to obtain granules displaying various levels of compressive strength. Three different inertization matrices were used in the experiments, the first consisting solely of Portland cement, the second of Portland cement and a superplasticizer additive, and the third of Portland cement partially replaced with silica-fume and superplasticizer. The results of the tests performed showed a very low level of leaching into the alkaline solidification solution for Cr3+, the quantity leached being under 2% as against higher levels for the other metallic elements. For all the considered elements, the best results were obtained by using silica-fume in the inertization matrix.

Adsorption↗

Recovery of copper from contaminated soil by flushing.

In this work the development of a process for the recovery of copper from contaminated industrial soils is presented. Experimental tests on a standard soil contaminated with a solution of copper chloride were carried out. The metal was extracted from the contaminated soil by flushing with a 0.1 M aqueous solution of an ethylenediaminetetraacetic acid (EDTA) sodium salt. A maximum copper extraction efficiency of about 60% was observed. Copper was then separated from the extracted solution by precipitation with sodium hydroxide after addition of ferric sulfate.

Chelating Agents↗

Arthroscopic treatment of anterior ankle impingement.

Ankle arthroscopy has recently allowed the elaboration of less invasive techniques for the treatment of anterior impingement. Its indications, advantages, and drawbacks in this application are discussed. Between 1987 and 1994, 133 patients were treated for ankle impingement. Among them, 58 patients, 37 men and 21 women (mean age, 28.5 years), who had failed a trial of conservative treatment were treated by means of tibiotalar arthroscopy. Twenty-seven were athletes engaged in sports with abnormal stressing of the ankle. According to McDermott's radiological classification, there were 15 stage I cases, 23 stage II, 13 stage III, and 7 stage IV. Preoperative evaluation with a modified version of McGuire's scoring system gave 50 cases rated as "poor" (< 60 points) and 8 cases rated as "fair" (60-67 points). Treatment consisted of removal of adhesions, cartilage shaving, and removal of the bone impingement with powered instruments, curettes, or small osteotomes. Follow-up was from 8 to 62 months (mean, 21.5 months). The postoperative McGuire ratings were 37 good, 13 fair, and 8 poor. There were no major complications. Recurrence of impingement was observed in four cases of stage III and IV. The conclusion is drawn that ankle arthroscopy is a sound method for the treatment of anterior impingement. Even in cases with severe joint cartilage impairment, it plays a therapeutic role as a means of postponing a possible arthrodesis.

Adult↗

Atrial natriuretic peptide in normotensive and hypertensive heart transplanted patients.

AIM OF THE STUDY: The present study is aimed to investigate the 24-hour pattern of Atrial Natriuretic Peptide (ANP) plasma concentration in normotensive (N) and hypertensive (H) heart transplanted patients (HTP) in order to detect the pathophysiological role of blood pressure regimen for ANP increase in HTP. METHODS: Eight NHTP and five HHTP have been investigated, all being hemodynamically compensated, without histological evidence of rejection and treated by Cyclosporine, Azathioprine and Prednisone. The control group was constituted by 10 clinically healthy subjects (CHS). ANP was assayed six times over the 24 h span. The contrasts between groups were statistically analyzed by means of Student's t-test for the 24 h mean values. RESULTS: The t-test found a statistically significant difference between the ANP 24 h mean levels either of CHS and HTP or NHTP and HHTP. The ANP 24 h mean plasma levels are increased of 190.4% in HHTP and of 44.3% in NHTP in comparison with CHS. DISCUSSION: The findings suggest that the further elevation of ANP in HHTP is a compensatory mechanism to antagonize high blood pressure. Moreover, being the ANP percent increase in HHTP three times more.

Adult↗

Chronobiometric identification of disorders of hunger sensation in essential obesity: therapeutic effects of dexfenfluramine.

In human beings, hunger is a proprioceptive signal that shows intraday (circadian components) and within-day (ultradian components) recursivity. Both periodic components can be investigated by chronobiometric procedures by combining the Cosinor method with spectral analysis. A 24-hour profile of hunger sensation (HS) can be plotted on a 1-to-10 scale of intensity using self-rated scores performed every half-hour of the day. Circadian and ultradian components were studied in 60 patients affected by essential obesity (20 men and 40 women; mean age, 38.4 years; mean body weight, 101 kg) before and after treatment with dexfenfluramine (Isomeride; Servier, Orléans, France) 15 mg orally twice daily, for 30 days. The control group consisted of 30 clinically healthy subjects (15 men and 15 women; mean age, 37.5 years; mean body weight, 69 kg). Chronobiometric analysis shows three patterns in obese patients, which suggests that HS may be normal (eurectic obesity), exaggerated (hyperrectic obesity), or diminished (hyporectic obesity). After dexfenfluramine administration, HS was showed a substantial decrease in the daily mean level. The spectrum of resolution in circadian and ultradian components was found to be maintained in eurectic obesity and partially readjusted in hyperrectic and hyporectic obesities. This demonstrates that dexfenfluramine acts not only as an anorectic but also as a chronizer by interfering with the recursive components of HS. The anorectic and chronizing effects suggest that dexfenfluramine is a "chronoanorectic drug" that interacts with the chronobiologic properties of the serotoninergic system.

Adult↗

Interaction of trace elements in a longitudinal study of human milk from full-term and preterm mothers.

Concentrations of 8 trace elements (Fe, Cu, Zn, Se, Br, Pb, Rb, and Sr) at different lactation time were measured by the PIXE multi-elemental technique. Time dependence and interelement correlations were studied. A total of 200 milk samples from 32 lactating mothers were supplied from 2 to 120 d after delivery of 26 full-term and 6 preterm infants. All elements showed a lognormal frequency-distribution. The Fe, Cu, Zn, and Se contents in preterm milk were found to be somewhat different with respect to full-term milk. Cu, Zn, Se, Br, Pb, and Rb concentrations declined with lactation time, both in pre- and full-term samples. Sr and Fe contents did not show any change with time. Detailed analysis of data by partial correlation and multiple regression methods was performed. No substantial differences between preterm and full-term samples were found in the results of partial correlation analysis. Cu and Zn were found to be correlated with lactation time, whereas the measured time dependence for the other elements has to be attributed to the effect of the existing interelement correlation. All the measured elements appeared to be correlated with at least one other element. In particular, Se was inversely correlated with Zn and directly with Cu. The zinc and copper contents in milk can therefore depend on the variation in the mother selenium intake.

Adolescent↗

[Chronobiological standards of 24-hour arterial blood pressure validated by bayesian criteria].

The monodiagnosis of hypertension via ambulatory (A) blood pressure (BP) monitoring (M) is erroneous by definition. Its use has to be substituted by the chronodiagnosis. Because of the lack of an international standardization, the BP chronobiologic reference limits have to be computed on a small sample size. For this compilation, it is, however, unavoidable the recruitment of normotensive subjects using the WHO's fixed limits. These chronobiologic standards are by principle contaminated by false negatives and need a bayesian validation. Such a depuration has been made by reclassifying each subject using the BP time-qualified standards. A secondary sample was constituted on the true normotensive reclassified. This sample provided the a posteriori reference standards for BP. The bayesian chronobiologic reference standards seem to be the limits with which the chronodiagnosis of hypertension can be suitably done via ABPM.

Adult↗

Blood pressure 24-hour pattern in two industrialized countries (Italy and Japan) with a different culture in salt intake.

This study investigates the blood pressure (BP) 24-hour pattern in representative samples of 2 industrialized countries, Italy and Japan, showing different cultures in salt intake. BP was monitored by means of a noninvasive ambulatory device whose readings were analyzed by means of chronobiometric procedures. The results show that the 24-hour BP pattern is not substantially different in Italian and Japanese subjects. In particular, the expected lower BP in the Italians was not detected despite their lower salt intake. Because the 24-hour mean BP value was seen not to be proportional to salt intake, the hypothesis is formulated that maintenance of the pressure regimen within a given range of variability is a principle of human physiology. To comply with this rule the Japanese people are supposed to have ethnically developed a certain resistance to dietary salt for which their cardiovascular apparatus is protected (phyletic escape to dietary sodium excess).

Adult↗