Search PubMed⌕ Search

Biomedical subjects

Judith C Chow

Publications and source records attributed to Judith C Chow.

At least 19 recordsLinked to original sources
PubMed2006

Seasonal variations and mass closure analysis of particulate matter in Hong Kong.

The chemical characteristics of ambient particulate matters in urban and rural areas of Hong Kong were determined in this study. A monitoring program starting from November 2000 to February 2001 (winter) and June 2001 to August 2001 (summer) for PM10 and PM2.5 was performed at three monitoring stations in Hong Kong. Twenty-four-hour PM10 and PM2.5 samples were collected once every 6 days at two urban sites, PolyU and KT, and every 12 days at a background site, HT, with Hi-Vol samplers. High concentrations of OC, EC (except in PolyU), water-soluble ions and elements were observed in winter among the three sampling sites for PM10 and PM2.5 fractions. Seasonal variations were significant in background HT. Dilution effect due to the increase in mixing depth and precipitation in summer reduced the concentrations of particulate matters. Long-range transport could contribute to the higher concentrations of particulate matter in the winter. Chemical mass closure calculations were performed for PM10 and PM2.5 observed. Mass closure improved when separate factors (1.4 and 1.9 respectively) were used to convert water-soluble organic carbon (WSOC) and water-insoluble organic carbon (WINSOC) into corresponding organic masses. The urban sites showed high percentages of water-soluble ions in winter and high percentages of carbonaceous species in summer. Better results were obtained for the chemical mass closure analysis in winter than in summer. High temperature and solar radiation in summer increased the rate of the complex photochemical reaction in the atmosphere. Therefore the chemical mass closure analysis would underestimate the volatized species and secondary aerosols during summer.

Air Pollutants↗
PubMed2006

Comparison of particle light scattering and fine particulate matter mass in central California.

Particle light scattering (Bsp) from nephelometers and fine particulate matter (PM2.5) mass determined by filter samplers are compared for summer and winter at 35 locations in and around California's San Joaquin Valley from December 2, 1999 to February 3, 2001. The relationship is described using particle mass scattering efficiency (sigmasp) derived from linear regression of Bsp on PM2.5 that can be applied to estimated PM2.5 from nephelometer data within the 24-hr filter sampling periods and between the every-6th-day sampling frequency. An average of sigmaSp = 4.9 m2/g was found for all of the sites and seasons; however, sigmasp averaged by site type and season provided better PM2.5 estimates. On average, the sigmasp was lower in summer than winter, consistent with lower relative humidities, lower fractions of hygroscopic ammonium nitrate, and higher contributions from fugitive dust. Winter average sigmasp were similar at non-source-dominated sites, ranging from 4.8 m2/g to 5.9 m2/g. The sigmasp was 2.3 m2/g at the roadside, 3.7 m2/g at a dairy farm, and 4.1 m2/g in the Kern County oilfields. Comparison of Bsp from nephelometers with and without a PM2.5 inlet at the Fresno Supersite showed that coarse particles contributed minor amounts to light scattering. This was confirmed by poorer correlations between Bsp and coarse particulate matter measured during a fall sampling period.

Air Pollutants, Occupational↗
PubMed2006

Comparison of continuous and filter-based carbon measurements at the Fresno supersite.

Results from six continuous and semicontinuous black carbon (BC) and elemental carbon (EC) measurement methods are compared for ambient samples collected from December 2003 through November 2004 at the Fresno Supersite in California. Instruments included a multi-angle absorption photometer (MAAP; lambda = 670 nm); a dual-wavelength (lambda = 370 and 880 nm) aethalometer; seven-color (lambda = 370, 470, 520, 590, 660, 880, and 950 nm) aethalometers; the Sunset Laboratory carbon aerosol analysis field instrument; a photoacoustic light absorption analyzer (lambda = 1047 nm); and the R&P 5400 ambient carbon particulate monitor. All of these acquired BC or EC measurements over periods of 1 min to 1 hr. Twenty-four-hour integrated filter samples were also acquired and analyzed by the Interagency Monitoring of Protected Visual Environments (IMPROVE) thermal/optical reflectance carbon analysis protocol. Site-specific mass absorption efficiencies estimated by comparing light absorption with IMPROVE EC concentrations were 5.5 m2/g for the MAAP, 10 m2/g for the aethalometer at a wavelength of 880 nm, and 2.3 m2/g for the photoacoustic analyzer; these differed from the default efficiencies of 6.5, 16.6, and 5 m2/g, respectively. Scaling absorption by inverse wavelength did not provide equivalent light absorption coefficients among the instruments for the Fresno aerosol measurements. Ratios of light absorption at 370 nm to those at 880 nm from the aethalometer were nearly twice as high in winter as in summer. This is consistent with wintertime contributions from vehicle exhaust and from residential wood combustion, which is believed to absorb more shorter-wavelength light. To reconcile BC and EC measurements obtained by different methods, a better understanding is needed of the wavelength dependence of light-absorption and mass-absorption efficiencies and how they vary with different aerosol composition.

Air Pollutants, Occupational↗
PubMed2006

Nanoparticle and ultrafine particle events at the Fresno supersite.

Continuous measurements of particle size distributions of 3-407 nm were collected from August 2002 to July 2004 at the Fresno Supersite to understand their number concentrations, size distributions, and formation processes. Measurements for fine particulate matter (PM2.5) mass, sulfate (SO4(2-)), nitrate (NO3-), black carbon (BC), particle-bound polycyclic aromatic hydrocarbons (PAHs), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O3), and meteorological data (wind speed, wind direction, temperature [T], relative humidity [RH], and solar radiation) were used to determine the causes of nanoparticle (3-10 nm) and ultrafine (10-100 nm) particle events. These events were found to be divided into four types: (1) 3- to 10-nm morning nucleation; (2) 10- to 30-nm morning traffic; (3) 10- to 30-nm afternoon photochemical; and (4) 50- to 84-nm evening home heating, including residential wood combustion. Intense examples of the first type (>10(4) number [#]/cm3) were observed on 29 days, nearly always during the summer. The second type of event was observed on more than 73 days and occurred throughout the year. The third type was observed on 36 days, from spring through summer. The fourth type was found on 109 days, all of them during the winter. Although sulfur dioxide (SO2) emissions in Central California are low, the small residual amounts in gasoline and diesel fuel are apparently sufficient to initiate nucleation events. These were measured in the morning, soon after the shallow surface inversion coupled with layers aloft where nucleation probably was initiated. PM2.5 concentrations were poorly correlated with nanoparticle number.

Air Pollutants, Occupational↗
PubMed2006

Feasibility of soil dust source apportionment by the pyrolysis-gas chromatography/mass spectrometry method.

This study tested the feasibility of using pyrolysis (Py)-gas chromatography (GC)/mass spectrometry (MS) to obtain organic chemical species data suitable for source apportionment modeling of soil-derived coarse particulate matter (PM10) dust on ambient filters. A laboratory resuspension apparatus was used with known soils to generate simulated receptor filter samples loaded with approximately 0.4 mg of PM10 dust, which is within the range of mass loading on ambient filters. Py-GC/MS at 740 degrees C generated five times more resolvable compounds than were obtained with thermal desorption GC/MS at 315 degrees C. The identified compounds were consistent with literature from Py experiments using larger samples of bulk soils. A subset of 91 organic species out of the 178 identified Py products was used as input to CMB8 software in a demonstration of source apportionment using laboratory-generated mixtures simulating ambient filter samples. The 178 quantified organic species obtained by Py of soil samples is an improvement compared with the 38 organic species obtained by thermal desorption of soils and the four functionally defined organic fractions reported by thermal/ optical reflectance. Significant differences in the concentration of specific species were seen between samples from different sites, both geographically distant and close, using analysis of variance and cluster analysis. This feasibility study showed that Py-GC/MS can generate useful source profile data for receptor modeling and justifies continued method development.

Cluster Analysis↗
PubMed2006

Exposure to PM2.5 and PAHs from the Tong Liang, China epidemiological study.

Chemically speciated PM2.5 and particle-bound polycyclic aromatic hydrocarbon (PAH) measurements were made at three sites near urban Tong Liang, Chongqing, a Chinese inland city where coal combustion is used for electricity generation and residential purposes outside of the central city. Ambient sampling was based on 72-hr averages between 3/2/2002 and 2/26/2003. Elevated PM2.5 and PAH concentrations were observed at all three sites, with the highest concentrations found in winter and the lowest in summer. This reflects a coupling effect of source variability and meteorological conditions. The PM2.5 mass estimated from sulfate, nitrate, ammonium, organics, elemental carbon, crustal material, and salt corresponded with the annual average gravimetric mass within +/-10%. Carbonaceous aerosol was the dominant species, while positive correlations between organic carbon and trace elements (e.g., As, Se, Br, Pb, and Zn) were consistent with coal-burning and motor vehicle contributions. Ambient particle-bound PAHs of molecular weight 168-266 were enriched by 1.5 to 3.5 times during the coal-fired power plant operational period. However, further investigation is needed to determine the relative contribution from residential and utility coal combustion and vehicular activities.

Air Pollutants↗
PubMed2006

Correlation of in vitro cytokine responses with the chemical composition of soil-derived particulate matter.

We treated human lung epithelial cells, type BEAS-2B, with 10-80 microg/cm2 of dust from soils and road surfaces in the western United States that contained particulate matter (PM) < 2.5 microm aerodynamic diameter. Cell viability and cytokine secretion responses were measured at 24 hr. Each dust sample is a complex mixture containing particles from different minerals mixed with biogenic and anthropogenic materials. We determined the particle chemical composition using methods based on the U.S. Environmental Protection Agency Speciation Trends Network (STN) and the National Park Service Interagency Monitoring of Protected Visual Environments (IMPROVE) network. The functionally defined carbon fractions reported by the ambient monitoring networks have not been widely used for toxicology studies. The soil-derived PM2.5 from different sites showed a wide range of potency for inducing the release of the proinflammatory cytokines interleukin-6 (IL-6) and IL-8 in vitro. Univariate regression and multivariate redundancy analysis were used to test for correlation of viability and cytokine release with the concentrations of 40 elements, 7 ions, and 8 carbon fractions. The particles showed positive correlation between IL-6 release and the elemental and pyrolyzable carbon fractions, and the strongest correlation involving crustal elements was between IL-6 release and the aluminum:silicon ratio. The observed correlations between low-volatility organic components of soil- and road-derived dusts and the cytokine release by BEAS-2B cells are relevant for investigation of mechanisms linking specific air pollution particle types with the initiating events leading to airway inflammation in sensitive populations.

Air Pollutants↗
PubMed2005

Particulate carbon measurements in California's San Joaquin Valley.

Aerosol carbon sampling methods and biases were evaluated during the California Regional PM10/PM2.5 Air Quality Study (CRPAQS) and Fresno Supersite programs. PM2.5 sampling was conducted using Desert Research Institute (DRI) sequential filter samplers (SFS) from December 1999 through February 2001 at two urban sites (Fresno and Bakersfield), one regional transport site (Angiola), and two boundary sites (Bethel Island and Sierra Nevada Foothills) during CRPAQS in the San Joaquin Valley (SJV). Additional filter-based sampling was done in Fresno as part of the US Environmental Protection Agency (EPA) Supersites program. Organic carbon (OC) and elemental carbon (EC) concentrations were higher during winter (December-February) than summer (June-August) and this trend was most pronounced at Fresno and Bakersfield. OC and EC displayed similar diurnal trends during winter and summer at Fresno and during winter at Angiola. The diurnal pattern at Angiola reflected the transport of secondary pollutants to the site. Collocated measurements of OC and EC on undenuded quartz-fiber filters were made at Fresno with the DRI SFS and the Andersen FRM and RAAS samplers. All average differences in OC between samplers were less than their respective measurement uncertainties. Positive and negative OC biases were evaluated at Fresno using the Andersen RAAS sampler with carbon-denuded and undenuded channels with Teflon-membrane and quartz-fiber filter pairs. Differences between the denuded particle OC and that obtained by subtracting the quartz-behind-Teflon or quartz-behind-quartz OC from the undenuded quartz-fiber front filter were less than twice their measurement uncertainties in most cases. Particulate OC in the denuded channel agreed most closely with the difference between undenuded front and backup quartz-fiber OC.

Aerosols↗
PubMed2005

Variations of nanoparticle concentrations at the Fresno Supersite.

Particle size distributions from 3 nm to 2 mum were measured at the Fresno, CA, Supersite from August 25, 2002 through July 31, 2003. Nanoparticle (3-10 nm) concentrations and the ratio of nanoparticle to total particle concentration were inversely related to particle surface areas from 50 to 1000 mum(2) cm(-3). Elevated nanoparticle concentrations were associated with motor vehicle emissions and with photochemical particle production. In contrast with Atlanta, GA, where concentrations of photochemically derived nanoparticles exceeded 10(5) cm(-3), 5-min average nanoparticle concentrations in Fresno never exceeded 24,400 cm(-3). While photochemical particle production occurs in Fresno, evidence of new particle production (i.e., an increase in number concentration with decreasing size below 10 nm) was not observed. This suggests that photochemical particle production may have occurred at a higher altitude followed by mixing to the surface, or that the fresh particle production rate was smaller with respect to the loss rate by coagulation than it was in Atlanta. Lower production rates in Fresno are more consistent with lower concentrations of sulfur precurors and low relative humidity in Fresno than they are in Atlanta.

Journal Article↗
PubMed2005

PM2.5 chemical composition in Hong Kong: urban and regional variations.

Chemically speciated PM2.5 measurements were made at roadside, urban, and rural background sites in Hong Kong for 1 year during 2000/2001 to determine the spatial and temporal variations of PM2.5 mass and chemical composition in this highly populated region. Annual average PM2.5 concentrations at the urban and rural sites were 34.1 and 23.7 microg m(-3), respectively, approximately 50-100% higher than the United States' annual average National Ambient Air Quality Standard (NAAQS) of 15 microg m(-3). Daily PM2.5 concentrations exceeded the U.S. 24-h NAAQS of 65 microg m(-3) on 19 days, reaching 131+/-8 microg m(-3) at the roadside site on 02/28/2001. Carbonaceous aerosol is the largest contributor to PM2.5 mass (explaining 52-75% of PM2.5 mass at the two urban sites and 32% at the background site), followed by ammonium sulfate (ranging from 23% to 37% at the two urban sites and 51% at the background site). Ammonium sulfate and crustal concentrations showed more uniform spatial distributions, while the largest urban-rural contrasts found in carbonaceous aerosol (likely due to emissions from on-road gasoline and diesel vehicles). Marine influences accounted for 7% of the mass at the background site (more than twice as much as at the two urban sites). Ternary diagrams are utilized to illustrate the different spatial patterns.

Journal Article↗
PubMed2005

Determination of the organic aerosol mass to organic carbon ratio in IMPROVE samples.

The ratio of organic mass (OM) to organic carbon (OC) in PM(2.5) aerosols at US national parks in the IMPROVE network was estimated experimentally from solvent extraction of sample filters and from the difference between PM(2.5) mass and chemical constituents other than OC (mass balance) in IMPROVE samples from 1988 to 2003. Archived IMPROVE filters from five IMPROVE sites were extracted with dichloromethane (DCM), acetone and water. The extract residues were weighed to determine OM and analyzed for OC by thermal optical reflectance (TOR). On average, successive extracts of DCM, acetone, and water contained 64%, 21%, and 15%, respectively, of the extractable OC, respectively. On average, the non-blank-corrected recovery of the OC initially measured in these samples by TOR was 115+/-42%. OM/OC ratios from the combined DCM and acetone extracts averaged 1.92 and ranged from 1.58 at Indian Gardens, AZ in the Grand Canyon to 2.58 at Mount Rainier, WA. The average OM/OC ratio determined by mass balance was 2.07 across the IMPROVE network. The sensitivity of this ratio to assumptions concerning sulfate neutralization, water uptake by hygroscopic species, soil mass, and nitrate volatilization were evaluated. These results suggest that the value of 1.4 for the OM/OC ratio commonly used for mass and light extinction reconstruction in IMPROVE is too low.

Aerosols↗
PubMed2005

Comparison of PM2.5 carbon measurement methods in Hong Kong, China.

Samples from Hong Kong, China, were analyzed for organic carbon (OC), elemental carbon (EC), and total carbon (TC) by three thermal protocols (low-temperature IMPROVE and high-temperature STN and NIOSH) and two optical monitoring methods: reflectance and transmittance. Good agreement (+/-10%) for TC among the three protocols was observed for sample loadings of 1-55 microg m(-3). The two protocols using a reflectance pyrolysis correction showed best agreement for EC, with <20% differences found for approximately 80% of the samples. Hong Kong has a large diesel fleet, and for some heavily loaded samples the light transmittance was too low for quantitative detection, resulting in large uncertainties in the OC/EC split based on transmittance. Hong Kong experienced OC levels similar to those at US sites, but has much higher EC concentrations. OC/EC ratios range from 2 to 5 at two US sites and from 0.2 to 1.2 at three Hong Kong sites.

Aerosols↗
PubMed2005

Seasonal and spatial variation of solvent extractable organic compounds in fine suspended particulate matter in Hong Kong.

The results of a 12-month study of more than 100 solvent extractable organic compounds (SEOC) in particulate matter (PM) less than or equal to 2.5 microm (PM2.5) collected at three air monitoring stations located at roadside, urban, and rural sites in Hong Kong are reported. The total yield of SEOC that accounts for approximately 8-18% of organic carbon (OC) determined by a thermal optical transmittance method was 125-2060 ng/m3, which included 14.6-128 ng/m3 resolved aliphatic hydrocarbons, 39.4-1380 ng/m3 unresolved complex mixtures, 0.6-17.2 ng/m3 polycyclic aromatic hydrocarbons, 41.6-520 ng/m3 fatty acids, and < 0.1-12.1 ng/m3 alkanols. Distinct seasonal variations (summer/winter differences) were observed with higher concentrations of the total and each class of SEOC in the winter and lower concentrations in the summer. Spatial variations are also obvious, with the roadside samples having the highest concentrations of SEOC and the rural samples having the lowest concentrations in all seasons. Characteristic ratios of petroleum hydrocarbons, such as carbon preference index, unresolved to resolved components, and carbon number with maximum concentration, suggest that PM2.5 carbon in Hong Kong originates from both biogenic and anthropogenic sources. The proportion of SEOC in PM2.5 from anthropogenic sources is estimated.

Air Pollutants↗
PubMed2005

Loss of PM2.5 nitrate from filter samples in central California.

Evaporative loss of particulate matter (with aerodynamic diameter < 2.5 microm, [PM2.5]) ammonium nitrate from quartz-fiber filters during aerosol sampling was evaluated from December 3, 1999, through February 3, 2001, at two urban (Fresno and Bakersfield) and three nonurban (Bethel Island, Sierra Nevada Foothills, and Angiola) sites in central California. Compared with total particulate nitrate, evaporative nitrate losses ranged from < 10% during cold months to > 80% during warm months. In agreement with theory, evaporative loss from quartz-fiber filters in nitric acid denuded samplers is controlled by the ambient nitric acid-to-particulate nitrate ratio, which is determined mainly by ambient temperature. Accurate estimation of nitrate volatilization requires a detailed thermodynamic model and comprehensive chemical measurements. For the 14-month average of PM2.5 acquired on Teflon-membrane filters, measured PM2.5 mass was 8-16% lower than actual PM2.5 mass owing to nitrate volatilization. For 24-hr samples, measured PM2.5 was as much as 32-44% lower than actual PM2.5 at three California Central Valley locations.

Aerosols↗
PubMed2004

Emissions of air pollutants from household stoves: honeycomb coal versus coal cake.

Domestic coal combustion can emit various air pollutants. In the present study, we measured emissions of particulate matter (PM) and gaseous pollutants from burning a specially formulated honeycomb coal (H-coal) and a coal cake (C-coal). Flue gas samples for PM2.5, PM coarse (PM2.5-10), and TSP were collected isokinetically using a cascade impactor; PM mass concentrations were determined gravimetrically. Concentrations of SO2, NOx, and ionic Cr(VI) in PM were analyzed using spectrometric methods. Fluoride concentrations were measured using a specific ion electrode method. PM elemental components were analyzed using an X-ray fluorescence technique. Total (gas and particle phase) benzo[a]pyrene (BaP) concentration was determined using an HPLC/fluorescence method. Elemental and organic carbon contents of PM were analyzed using a thermal/optical reflectance technique. The compositional and structural differences between the H-coal and C-coal resulted in different emission characteristics. In generating 1 MJ of delivered energy, the H-coal resulted in a significant reduction in emissions of SO2 (by 68%), NOx (by 47%), and TSP (by 56%) as compared to the C-coal, whereas the emissions of PM2.5 and total BaP from the H-coal combustion were 2-3-fold higher, indicating that improvements are needed to further reduce emissions of these pollutants in developing future honeycomb coals. Although the H-coal and the C-coal had similar emission factors for gas-phase fluoride, the H-coal had a particle-phase fluoride emission factor that was only half that of the C-coal. The H-coal had lower energy-based emissions of all the measured toxic elements in TSP but higher emissions of Cd and Ni in PM2.5.

Air Pollutants↗