Biomedical subjects

J P Santerre

Publications and source records attributed to J P Santerre.

At least 19 recordsLinked to original sources

PubMed2007

Fibrinogen adsorption and platelet lysis characterization of fluorinated surface-modified polyetherurethanes.

A polyetherurethane (PU) was modified using fluorinated surface-modifying macromolecules (SMMs). A double radiolabel method was used simultaneously to measure the number of adhered platelets ((51)Cr) and the quantity of adsorbed Fg ((125)I), in a cone-and-plate instrument. The objectives were to determine if adsorbed Fg levels correlated to platelet adhesion on the surfaces, and to assess if any reductions in platelet adhesion for the SMM-treated surfaces resulted from surface-induced platelet lysis, rather than changes directly related to lower platelet activation and attachment on the novel surfaces. Platelet lysis was determined from lactate dehydrogenase (LDH) and unbound (51)Cr released into plasma isolated from whole blood exposed to test materials. The corresponding Fg adsorption, evaluated under the same platelet adhesion conditions, did not account for the reduced platelet adhesion on the treated surfaces. LDH and (51)Cr platelet release were very low and indicated no statistically significant differences between the materials. It was therefore concluded that platelet lysis did not contribute to the reduction in platelet adhesion characteristic observed on the SMM-treated surfaces. More importantly, the work emphasizes that the platelet activation cannot be inferred to by assessing the quantity of fibrinogen as is commonly done in the literature. The finding suggests a much more complex mechanism of action for the SMM surface modifiers. On-going work is investigating other Fg parameters such as protein binding affinity and protein conformational state in order to establish the mechanism by which the fluorinated surface modifiers may be reducing platelet adhesion via intermediary changes in initial protein adsorption.

Adsorption↗

PubMed2007

Influence of silanated filler content on the biodegradation of bisGMA/TEGDMA dental composite resins.

It has been shown that an increase in the content of nonsilanated submicron colloidal silica filler particles within dental composites resulted in the release of more bis-phenol-A diglycidyl dimethacrylate (bisGMA)-derived product, bis-hydroxy-propoxyphenyl propane, following incubation with cholesterol esterase (CE). This work further investigates the enzyme-catalyzed biodegradation of fine composite resin systems, containing silanated micron-size irregular glass fillers, commonly used in clinical restorations. Model composite resin samples (10 or 60% weight fraction silanated barium glass filler, 1 mum average particle size) based on bisGMA/triethylene glycol dimethacrylate (TEGDMA) were incubated in buffer or buffer with CE (pH = 7.0, 37 degrees C) solutions for 32 days. The incubation solutions were analyzed using high-performance liquid chromatography, UV spectroscopy, and mass spectrometry. Both groups were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray photoelectron spectroscopy. In contrast with previous findings for nonsilanated submicron filler systems, the higher filler containing composite showed an increase in its stability with time, following exposure to esterase and when compared to the lower filler content material. As well, the 60% filler composite leached less unreacted monomer TEGDMA. Since the model composite resins studied here were identical and only the filler content varied, the differences in biostability could be specifically associated with the relative amount of resin/filler distribution. The clinical use of different materials in varied dental applications (ranging from fissure sealant to tooth-colored highly filled materials) must consider the potential for different degradation profiles to occur as a function of filler content.

Composite Resins↗

PubMed2005

Fibrinogen surface distribution correlates to platelet adhesion pattern on fluorinated surface-modified polyetherurethane.

In previous work, it had been shown that platelet adhesion could be reduced by fluorinating surfaces with oligomeric fluoropolymers, referred to as surface-modifying macromolecules (SMMs). In the current study, two in vitro blood-contacting experiments were carried out on a polyetherurethane modified with three different SMMs in order to determine if altered platelet adhesion levels could be related to the pattern of adsorbed protein and more specifically to the manner in which fibrinogen (Fg) distribution occurs at the surface. In the first experiment, the materials were placed in whole human blood and the adherent platelets were viewed with high-resolution scanning electron microscopy (SEM). In a second experiment, the materials were incubated with human plasma with the absence of platelets. The plasma contained 5% fluorescent-Fg. The materials were then viewed with a fluorescence microscope and images were collected to define the distribution of high-density fluorescent-Fg areas. The SEM and fluorescent-Fg images were imported to Image Pro Plus imaging software to measure the area, length and circularity and a bivariate correlation test was conducted between the two sets of data. For area and length morphology parameters, there were high and significant correlations (r > 0.9, p < 0.05) between the platelets and Fg aggregates. The data suggest that the Fg distribution may serve as a predictor of platelet morphology/activation and provides insight into the non-thrombogenic character of biomaterials containing the fluorinated SMMs.

Adsorption↗

PubMed2005

Understanding the biodegradation of polyurethanes: from classical implants to tissue engineering materials.

After almost half a century of use in the health field, polyurethanes (PUs) remain one of the most popular group of biomaterials applied for medical devices. Their popularity has been sustained as a direct result of their segmented block copolymeric character, which endows them with a wide range of versatility in terms of tailoring their physical properties, blood and tissue compatibility, and more recently their biodegradation character. While they became recognized in the 1970s and 1980s as the blood contacting material of choice in a wide range of cardiovascular devices their application in long-term implants fell under scrutiny with the failure of pacemaker leads and breast implant coatings containing PUs in the late 1980s. During the next decade PUs became extensively researched for their relative sensitivity to biodegradation and the desire to further understand the biological mechanisms for in vivo biodegradation. The advent of molecular biology into mainstream biomedical engineering permitted the probing of molecular pathways leading to the biodegradation of these materials. Knowledge gained throughout the 1990s has not only yielded novel PUs that contribute to the enhancement of biostability for in vivo long-term applications, but has also been translated to form a new class of bioresorbable materials with all the versatility of PUs in terms of physical properties but now with a more integrative nature in terms of biocompatibility. The current review will briefly survey the literature, which initially identified the problem of PU degradation in vivo and the subsequent studies that have led to the field's further understanding of the biological processes mediating the breakdown. An overview of research emerging on PUs sought for use in combination (drug + polymer) products and tissue regeneration applications will then be presented.

Absorbable Implants↗

PubMed2004

The influence of resin chemistry on a dental composite's biodegradation.

Previous work reported that commercial dental composite resins containing a urethane-modified bisGMA (bisphenylglycidyl dimethacrylate)/TEGDMA (triethylene glycol dimethacrylate) (ubis) based monomer system showed a 10-fold reduction in the release of a bisGMA-derived product, bishydroxypropoxyphenyl propane (bisHPPP), as compared with that found for bisGMA/TEGDMA (bis) based composites after incubation with cholesterol esterase (CE). Unfortunately, these materials also differed substantially in filler type and content, making it impossible to directly relate any specific parameter to the differences in biodegradation levels. By controlling for filler content and type, the current study will seek to probe the biomolecular interactions between composite resin chemistry and esterase activity in order to help explain the observed differences in biodegradation levels between the ubis and bis resin systems. After 32 days of incubation, buffer and CE solutions were analyzed for degradation products using high-performance liquid chromatography, UV spectroscopy, and mass spectrometry. Both materials were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray photoelectron spectroscopy. In the CE groups, the ubis system showed a 2.6- to 86-fold reduction (dependent on the product) in the amount of isolated products relative to the bis system (p < 0.01). Scanning electron microscopy data also demonstrated the relative stability of the ubis system and X-ray photoelectron spectroscopy analysis showed a higher content of the ester bond at the surface of the bis samples. Fourier transform infrared data showed that both resins had similar conversions. Because both systems were identical except for their monomer systems, it was concluded that changes in biostability were associated with chemistry. Crosslinking, hydrophobicity, and solubility all relate to ubis's pro-stability.

Acrylic Resins↗

PubMed2004

Mutual influence of cholesterol esterase and pseudocholinesterase on the biodegradation of dental composites.

It has been demonstrated that human saliva contains cholesterol esterase (CE)- and pseudocholinesterase (PCE)-like hydrolase activities. While PCE has been shown to preferentially degrade triethylene glycol dimethacrylate (TEGDMA) and its derivatives, CE has a greater catalytic effect on the breakdown of bis-phenol-A-diglycidyl dimethacrylate (bisGMA) components in composite dental resins. The current study seeks to determine if there is a mutual influence between the different esterases with respect to the biodegradation of resin composite. Photopolymerized model composite resin samples (containing 60% by weight fraction of silanated barium glass filler) based on bisGMA/TEGDMA (bis) or urethane-modified bisGMA/TEGDMA/bisEMA (ubis) monomers were incubated in buffer, CE and/or PCE solutions (pH=7.0, 37 degrees C) for 8 and 16 days. The incubation solutions were analyzed for degradation products using high-performance liquid chromatography, UV spectroscopy and mass spectrometry. In the bis system, higher amounts (p<0.05) of a bisGMA derived product, bishydroxy-propoxyphenyl-propane (bisHPPP), were detected in the combined enzyme group as compared to the sum of the two individual enzyme groups. In the ubis system, similar comparisons showed that higher levels (p<0.05) of bisHPPP were detected in the combined group at 8 days while higher amounts (p<0.05) of a bisEMA derived product, ethoxylated bis-phenol A, were detected in the combined group at 16 days. The study concluded that CE and PCE act synergistically to increase the biodegradation of both composite resin materials.

Acrylic Resins↗

PubMed2004

Modulation of collagen proteolysis by chemical modification of amino acid side-chains in acellularized arteries.

In this study, we have examined the effects of specific chemical modifications of amino acid side-chains on the in vitro degradation of "native" collagen obtained from acellular matrix (ACM)-processed arteries. Two monofunctional epoxides of different size and chemistry were used to modify lysine, with or without methylglyoxal modification of arginine. Biochemical, thermomechanical, tensile mechanical, and multi-enzymatic (collagenase, cathepsin B, acetyltrypsin, and trypsin) degradation analyses were used to determine the effects of modifications.Collagen solubilization by enzymes was found to depend upon the size and chemistry of epoxides used to modify lysine residues. In general, the solubilization of native ACM collagen by collagenase, cathepsin B, trypsin, and acetyltrypsin was either unaltered or decreased after modification with glycidol. In contrast, n-butylglycidylether (n-B) treatment increased solubilization by all enzymes. Subsequent arginine modification significantly reduced collagen solubilization by acetyltrypsin for glycidol-treated ACM arteries, whereas increased collagen solubilization was observed for n-B-treated ACM arteries with all enzymes. Gel chromatographic analyses of collagen fragments solubilized by trypsin revealed that both the amount and sites of cleavage were altered after lysine and arginine modification. The ability to modulate the enzymatic degradation of tissue-derived materials as demonstrated in this study may facilitate the design of novel engineering scaffolds for tissue regeneration or collagen-based drug delivery systems.

Amino Acid Sequence↗

PubMed2004

Effect of composite resin biodegradation products on oral streptococcal growth.

Hydrolytic degradation by-products associated with the constitutive monomers 2,2-bis [4-(2-hydroxy-3-methacryloxypropoxy) phenyl] propane (bis-GMA), bisphenol A polyethylene glycol diether dimethacrylate (bis-EMA), and triethylene glycol dimethacrylate (TEDGMA) used in dental restorative composites include bis-hydroxy-propoxyphenyl propane (bis-HPPP), ethoxylated bisphenol A (E-bisPA), methacrylic acid (MA), and triethylene glycol (TEG). These products are generated from the interaction of human salivary esterases with the composites. Recent findings have indicated that TEGDMA has the ability to modulate oral bacteria but it is unclear which components of TEGDMA are related to the observed effects. The objective of the current study was to investigate the influence of TEGDMA derived degradation products MA and TEG on the growth of three strains of oral bacteria: S. mutans strains NG8 and JH1005, and S. salivarius AT2. Bacterial growth rates were measured at 37 degrees C, and pH values of 5.5 (representative of cariogenic state) or 7.0 at concentrations of 0-50mmol/l for MA (Sigma, US) and 0-100mmol/l for TEG (Sigma, US). It was found that at pH 5.5 TEG significantly stimulated the growth of both S. mutans strains ( p<0.05 ) in the concentration range of 0.5-10.0mmol/l and stimulated the growth of S. salivarius AT2 for the entire concentration range tested (p<0.05). TEG (above 50mmol/1) did not significantly affect the doubling times of S. salivarius at pH of 7.0 and it inhibited the growth of both S. mutans strains above 50mmol/l at the same pH value. At pH 5.5 MA inhibited the growth of all three strains with increasing concentration. At neutral pH, the growth of S. mutans NG8 strain was significantly reduced by MA ( p<0.05 ) above 10mmol/l. In summary, these results indicate that TEG and MA modulate the growth rate of important oral bacteria in a concentration and pH dependent manner.

Biodegradation, Environmental↗

PubMed2004

Salivary esterase activity and its association with the biodegradation of dental composites.

Pseudocholinesterase (PCE) and cholesterol esterase (CE) can hydrolyze bisphenylglycidyl dimethacrylate (bisGMA) and triethylene glycol dimethacrylate (TEGDMA) monomers. This study will test the hypothesis that enzyme activities showing CE and PCE character are found in human saliva at levels sufficient to hydrolyze ester-containing composites important to restorative denstistry. The study also seeks to ask if the active sites of CE and PCE with respect to composite could be inhibited. Photo-polymerized model composite resin was incubated in PCE and CE solutions, in the presence and absence of a specific esterase inhibitor, phenylmethylsulfonyl fluoride (PMSF). Incubation solutions were analyzed for resin degradation products by high-performance liquid chromatography (HPLC), UV spectroscopy, and mass spectrometry. Saliva was found to contain both hydrolase activities at levels that could degrade composite resins. PMSF inhibited the composite degradation, indicating a material hydrolysis mechanism similar to the enzymes' common function.

Analysis of Variance↗

PubMed2003

The influence of protein adsorption and surface modifying macromolecules on the hydrolytic degradation of a poly(ether-urethane) by cholesterol esterase.

Previous investigations have demonstrated that the inflammatory cell derived enzyme, cholesterol esterase (CE) could degrade polyurethanes (PUs) by hydrolyzing ester and urethane bonds. Studies that have investigated the development of protective coatings for PUs have reported that the polymer degradation of polyester-urethanes (PESUs) can be reduced with the use of fluorine containing surface modifying macromolecules (SMMs). Since these latter studies were carried out in the presence of relatively pure enzyme, it has not been shown if SMMs would still provide an enhanced inhibitory effect if surfaces were pre-exposed to plasma proteins. This would be more representative of the in vivo scenario since protein adsorption would occur before the appearance of monocyte-derived macrophages which would be a primary source of esterase activities. The current investigation has focused on studying the influence of fibrinogen (Fg) as a simple model of protein adsorption in order to assess the effect of CE in combination with protein on polyether-urethane (PEU) surfaces. The materials were prepared with and without SMMs, and were pre-coated with Fg prior to carrying out biodegradation studies. The pre-adsorption of Fg onto the modified and non-modified surfaces provided a significant delay in the hydrolytic action of CE onto the PEU substrates. However, the effect was gone by 70 days and by the 126th day of incubation, both Fg coated and non-Fg coated groups had the same level of degradation. The difference between Fg coated and non-coated substrates was much smaller for materials containing SMMs. In addition, the pre-adsorption of Fg did not alter the SMMs' ability to provide a more biostable surface over the 4 month incubation period.

Adsorption↗

PubMed2003

Enzyme induced biodegradation of polycarbonate-polyurethanes: dose dependence effect of cholesterol esterase.

The current study has investigated the influence of esterase activity (80-400units/ml) on the biodegradation of polycarbonate-urethanes (PCNUs) by cholesterol esterase (CE), with a particular interest in studying the influence of different hard segment structures and their contribution to sensitizing the polymer towards enzyme catalyzed hydrolysis. Polycarbonate based polyurethanes were synthesized with varying hard segment content as well as hard segment chemistry based on three different diisocyanates, 1,6-hexane diisocyanate (HDI), 4,4'-methylene bisphenyl diisocyanate (MDI) and 4,4-methylene biscyclohexyl diisocyanate (HMDI). The effect of different chemistry on surface contact angle was measured in order to define the relative chemical nature of the surfaces. The enzyme dose response was found to be lower when hard segment content in the polymer was high. There was a very strong dependence on enzyme concentration for polyurethanes with different hard segment chemistry, despite the fact that the nature of the hydrolysable polycarbonate segment remained the same. The PCNU which showed the most dramatic dependence on enzyme concentration was synthesized with HMDI. At low enzyme concentration (80units/ml) this material was the most stable of the polymers while at elevated CE concentration (400units/ml) the polymer underwent a catastrophic breakdown. The findings suggested that protein binding on the surfaces was saturated even though enzyme degradation did not achieve saturation on any of the surfaces. The role of protein binding in modulating the hydrolytic action of the enzymes at different activity levels highlights a need for further study in this area.

Cyanates↗

PubMed2003

Isolation of methylene dianiline and aqueous-soluble biodegradation products from polycarbonate-polyurethanes.

Polycarbonate-polyurethanes (PCNUs) have provided the medical device industry with practical alternatives to oxidation-sensitive polyether-urethanes (PEUs). To date, many studies have focused on PCNUs synthesized with 4,4'-methylene diphenyl-diisocyanate (MDI). The relative hydrolytic stability of this class of polyurethanes is actually quite surprising given the inherent hydrolytic potential of the aliphatic carbonate group. Yet, there has been little information reporting on the rationale for the material's demonstrated hydrolytic stability. Recent work has shown that PCNU materials have a strong sensitivity towards hydrolysis when changes are made to their hard segment content and/or chemistry. However, knowledge is specifically lacking in regards of the identification of cleavage sites and the specific nature of the biodegradation products. Using high-performance liquid chromatography, radiolabel tracers and mass spectrometry, the current study provides insight into the distribution of biodegradation products from the enzyme-catalyzed hydrolysis of five different PCNUs. The hydrolytic sensitivity of the materials is shown to be related to the distribution of products, which itself is a direct consequence of unique micro-structures formed within the different materials. While an MDI-based polymer was shown to be the most hydrolytically stable material, it was the only PCNU that produced its diamine analog, in this case 4,4'-methylene dianiline (MDA), as a degradation product. Given the concern over aromatic diamine toxicity, this finding is important and highlights the fact that relative biostability is a distinct issue from that of degradation product toxicity, and that both must be considered separately when assessing the impact of biodegradation on biomaterial in vivo compatibility.

Aniline Compounds↗

PubMed2003

Surface modification of a polycarbonate-urethane using a vitamin-E-derivatized fluoroalkyl surface modifier.

Fluorinated surface-modifying macromolecules (SMMs) have been previously reported on and shown to limit the hydrolytic degradation of polyurethanes. The SMM molecules achieve this effect by allowing for the selective migration of terminal fluorinated groups to the polymer's surface, which may then shield more hydrolytically-sensitive groups in the base polyurethane backbone. A further extension of the SMM concept would be to utilize the migration of the fluorine tails to simultaneously deliver biologically active moieties to the surface. This study explored the synthesis and characterization of a vitamin-E (natural anti-oxidant) coupled surface modifier, as a model for the bioactive SMM concept. The SMM was synthesized using lysine diisocyanate (LDI), polycarbonate diol (PCN), and a fluoroalcohol. By derivatizing the LDI pendant ester, vitamin E was coupled to the SMM. The vitamin-E SMM was physically characterized using gel-permeation chromatography (GPC) and its anti-oxidant activity was assessed in the presence of 0.1 mM NaOCl. Polymer degradation experiments were carried out using 10 mM NaOCl incubation solutions, and the relative material breakdown was assessed using GPC and scanning electron microscopy (SEM). The results indicate that while the fluoro-component reduced damage of the PU, the bioactive component achieved a further deactivating effect. A similar action may also be effective against superoxide anions generated by human macrophages.

Biocompatible Materials↗

PubMed2003

Biodegradation of a dental composite by esterases: dependence on enzyme concentration and specificity.

Studies have shown that inflammatory (cholesterol esterase, CE) and salivary (pseudo-cholinesterase, PCE) enzymes can cause the breakdown of bisphenol-A diglycidyl dimethacrylate (bisGMA) and triethylene glycol dimethacrylate (TEGDMA) components from composite resins. Based on the above consideration, it was desired to show how CE- and PCE-catalyzed hydrolysis of resin components was dependent on the enzymes' concentration and to determine their distinct specificities (if any) towards resin components. Photopolymerized model composite resin samples (60% weight fraction silanated barium glass filler) based on bisGMA and TEGDMA monomers (55/45 weight ratio of the matrix, respectively) were incubated with PBS and either 0.01, 0.05, 0.1 or 1 unit/ml of CE or PCE for 16 days (pH 7.0, 37 degrees C). Incubation solutions were analyzed by high-performance liquid chromatography (HPLC), UV spectroscopy and mass spectrometry. The composite samples were characterized by scanning electron microscopy (SEM). Degradation rates of bisGMA and TEGDMA monomers were assessed. The results showed that CE had a greater specificity towards cleaving bisGMA while PCE showed a greater specificity towards TEGDMA. A strong enzyme concentration dependence was observed which suggests that the level of degradation products generated for a material will depend on the esterase make-up of an individual's saliva in combination with the specific formulation of monomer components used.

Biodegradation, Environmental↗

PubMed2002

The effect of polyethylene particle phagocytosis on the viability of mature human macrophages.

Macrophages are the major cell type observed in the inflammatory membrane retrieved at implant revision surgery. In this study, mature human monocyte-derived macrophages (MDM) were adapted to a previously established in vitro model to examine the influence of high-density polyethylene (HDPE) particulate (4-10 microm) on MDM viability. HDPE particles were suspended in soluble type I collagen, which subsequently was solidified on glass coverslips. Mature human macrophages, derived from differentiating peripheral blood monocytes on polystyrene for 10 days, were incubated in culture media on collagen controls and collagen-particle substrata for 31 days. Histologic analysis demonstrated that MDMs were in contact with the particles at 2 h. The majority of the particles were associated with the cells within 24 h. Based on electron microscopy, those cells associated with the particles appeared to be morphologically activated rather than necrotic or apoptotic. Assessment of cell viability revealed no differences among the groups at 24 h, but at 31 days significantly more viable cells and higher DNA values were found associated with the particle groups versus the collagen controls. The histologic results validate human mature MDMs as a clinically relevant cell type for study of the role of polyethylene particulate in aseptic loosening. The cell viability results indicate that phagocytosis of HDPE is not toxic to MDMs but in fact prolongs MDM survival. The long-lived MDMs may play a role in perpetuating chronic inflammation surrounding implants.

Cell Separation↗

PubMed2002

Fluorinated surface-modifying macromolecules: modulating adhesive protein and platelet interactions on a polyether-urethane.

Polyether-urethanes (PEUs) have been the materials of choice for the manufacture of conventional blood-contacting devices. Nevertheless, biostability and blood compatibility are still among the principal limitations in their long-term application. Studies investigating the development of protective coatings for PEUs have shown that degradation can be reduced with the use of fluorinated surface-modifying macromolecules (SMMs). It has also been hypothesized that SMM-modified PEU surfaces may exhibit improved blood compatibility because other studies have shown a modulation in fibrinogen adsorption onto these surfaces. To determine the blood compatibility of a PEU-containing fluorinated SMMs, a series of in vitro experiments were designed to study the pattern of protein adsorption from plasma and then to assess the nature of platelet adhesion and activation on each substrate. Western blot analysis as well as single protein studies revealed that the dominant "adhesive proteins" [fibrinogen (Fg), fibronectin (Fnc), and vitronectin (Vnc)] were adsorbed on two of the SMM-containing PEUs in lower amounts relative to unmodified base. Platelet adhesion and activation data further highlighted the differences among the various substrates. It was shown that the unmodified base had a higher number of adhered platelets relative to the SMM-modified surfaces, and that of the SMM-containing substrates, which showed the lowest levels of adhesive proteins also, exhibited significantly lower platelet densities. Close morphological examination further revealed that platelets residing on these latter substrates were not appreciably activated. Based on the current evidence, it is believed that the fluorinated SMMs demonstrate good potential for the development of surfaces with minimal thrombogenic character in in vivo applications.

Adsorption↗

PubMed2002

Biological characterization of a novel biodegradable antimicrobial polymer synthesized with fluoroquinolones.

Biomaterial-related infections continue to represent a significant challenge to the medical community. Several approaches have been utilized to incorporate antimicrobial agents at the surface of implant devices in attempts to delay or eliminate the formation of biofilms. To date, most of these strategies have focused on drug conjugation or diffusion-limited systems for the delivery of such pharmaceutical agents. More recently, work has been presented on the feasibility of incorporating drugs into the backbone of polymers as a main-chain monomer. When sequenced into the backbone of the polymer with other monomers that are hydrolytically sensitive to enzyme-catalyzed breakdown, it is thought that drugs may be able to be selectively released. Specifically, degradable polyurethanes have been synthesized with fluoroquinolone antibiotics and have shown an ability to kill bacteria when released following degradation of the polymer chains by the macrophage-derived enzyme cholesterol esterase. However, specificity of the cleavage sites in the polymer was difficult to control. Since cholesterol esterase has specificity for hydrophobic moieties, it is desirable to alter the formulation of the polyurethanes to incorporate long hydrophobic monomers immediately adjacent to the ciprofloxacin molecule. Hence, the current study focuses on evaluating the enzyme-catalyzed degradation of a degradable polyurethane synthesized with 1,12 diisocyanatododecane as a substitute for 1,6 diisocyanatohexane, which was used in previous work. Validation of specific ciprofloxacin release and the generation of antimicrobial are shown. A preliminary cell study to assess the cytotoxicity of this biodegradable antibiotic polymer shows that the material has no observable effects on cell proliferation or cell membrane structure.

Animals↗

PubMed2002

Interactions between resin monomers and commercial composite resins with human saliva derived esterases.

Cholesterol esterase (CE) and pseudocholinesterase (PCE) have been reported to degrade commercial and model composite resins containing bisphenylglycidyl dimethacrylate (BisGMA), triethylene glycol dimethacrylate (TEGDMA) or the latter in combination with urethane modified BisGMA monomer systems. In addition, human saliva has been shown to contain esterase like activities similar to CE and PCE. Hence, it was the aim of the current study to determine to what extent human saliva could degrade two common commercial composite resins (Z250 from 3M Inc. and Spectrum TPH from L.D. Caulk) which contain the above monomer systems. Saliva samples from different volunteers were collected, processed, pooled, and freeze-dried. TEGDMA and BisGMA monomers were incubated with human saliva derived esterase activity (HSDEA) and their respective hydrolysis was monitored using high performance liquid chromatography (HPLC). Both monomers were completely hydrolyzed within 25 h by HSDEA. Photopolymerized composites were incubated with buffer or human saliva (pH 7.0 and 37 C) for 2, 8 and 16 days. The incubation solutions were analyzed using HPLC and mass spectrometry. Surface morphology characterization was carried out using scanning electron microscopy. Upon biodegradation, the Z250 composite yielded higher amounts of BisGMA and TEGDMA related products relative to the TPH composite. However, there were higher amounts of ethoxylated bis-phenol A released from the TPH material. In terms of total mass of products released, human saliva demonstrated a greater ability to degrade Z250. In summary, HSDEA has been shown to contain esterase activities that can readily catalyze the biodegradation of current commercial composite resins.

Biocompatible Materials↗