Biomedical subjects

J E Bertram

Publications and source records attributed to J E Bertram.

25 records · Page 2Linked to original sources

PubMed1989

Telemetered in vivo strain analysis of locomotor mechanics of brachiating gibbons.

The slender elongated form that is characteristic of the forelimb long bones of gibbons (Hylobates) has long been attributed to their functional adaptation to habitual armswinging locomotion, although potential selective advantages of this morphology for brachiation have yet to be demonstrated. If the forces exerted on the limb skeleton during brachiation indeed differ greatly from those of other locomotor modes, then the changes in skeletal loading accompanying a shift in locomotor behaviour could favour alterations in skeletal morphology in brachiating lineages. In vivo skeletal strain patterns recorded by using radiotelemetry during brachiation indicate that the forelimb bones of the gibbon are loaded in substantial tension and show reduced bending and compression in comparison with those of other mammals. We suggest that this unique loading regime could have contributed to the evolution of the distinctive morphology of hylobatid limbs.

Animals↗

PubMed1988

Bone curvature: sacrificing strength for load predictability?

Nearly all long bones of terrestrial mammals that have been studied are loaded in bending. Yet bending requires greater bone mass than axial compression for effective support of equivalent static loads. Most long bones, in fact, are curved along their length; their curvature augmenting rather than diminishing stresses developed due to bending. The most "efficient" design of a bone (maximal strength per unit mass) should be a form which is straight and resists axial compression. Bone curvature and the bending developed in the long bones of most species studied, therefore, poses a paradox in design. However, under natural conditions an animal's skeleton must support a range of dynamic loads that vary in both direction and magnitude. Thus, improved predictability of dynamic loading should represent an important feature in the design of the bone, in addition to its absolute strength. We present an explanation of long bone curvature, based on the conditions of stability for bending vs. axial compression in a column, that describes this apparent design paradox as a mechanism for improving the predictability of loading direction (and, consequently, the pattern of stresses within the bone). Our hypothesis argues that in order to understand the design "effectiveness" of long bone shape the role of the bone as a structural unit must be redefined to one in which bone strength is optimized concurrently with loading predictability. In agreement with our hypothesis, bone curvature appears to meet this requirement.

Animals↗

PubMed1987

Functional design of horse hoof keratin: the modulation of mechanical properties through hydration effects.

Tensile moduli and J-integral fracture toughness values were determined for horse hoof-wall keratin at four hydration levels. The stiffness of hoof-wall was influenced by water content to a greater degree than is the stiffness of other mammalian hard keratins. Young's modulus increased from 410 MPa at 100% relative hydration (RH) to 14.6 GPa at 0% RH. Fracture toughness was maximal (22.8 kJ m-2) at an intermediate hydration (75% RH), which represents a two-fold increase over both fully hydrated and dehydrated material. Maximum fracture toughness occurred at a hydration level which is within the range that has been found in vivo in the hoof wall. These results lead to the hypothesis that the density of secondary bonding sites within the hoof-wall keratin matrix proteins provides the hoof organ with the means to modulate tissue properties, even though this epidermal tissue functions after the cells have died.

Animals↗

PubMed1986

Bone modeling during growth: dynamic strain equilibrium in the chick tibiotarsus.

Bone loading was quantified, using in vivo strain recordings, in the tibiotarsus of growing chicks at 4, 8, 12, and 17 weeks of age. The animals were exercised on a treadmill at 35% of their maximum running speed for 15 minutes/day. In vivo bone strains were recorded at six sites on the tibiotarsus. Percentages of the bone's length and a percentage of top running speed were used to define functionally equivalent sites on the bone, and a consistent exercise level over the period of growth was studied. The pattern of bone strain defined in terms of strain magnitude, sign, and orientation remained unchanged from 4-17 weeks of age, a period when bone mass and length increased 10-fold and threefold, respectively. Our findings support the hypothesis that bones model (and remodel) during growth to achieve and maintain a similar distribution of dynamic strains at functionally equivalent sites. Because strain magnitude and sign (tensile versus compressive) differed among recording sites, these data also suggest that cellular responses to strain-mediated stimuli differ from site to site within a bone.

Animals↗

PubMed1986

Fracture toughness design in horse hoof keratin.

An engineering fracture mechanics approach was applied to the analysis of the fracture resistance of equine hoof-wall. The relationship between fracture toughness and the morphological organization of the keratin hoof tissue was investigated. Fracture toughness was evaluated using the J-integral analysis method which employs the compact tension test geometry. Tensile tests were also conducted to evaluate the effect of the morphological organization on the stress-strain behaviour. Hoof-wall has greatest fracture resistance for cracks running proximally, parallel to the tubular component of the wall keratin. For fully hydrated material tested in this direction the mean critical J-integral value at failure was 1.19 X 10(4)J m-2. This was nearly three times greater than the value determined for the weakest orientation, in which the crack ran parallel to the material between the tubules. The lower fracture toughness of the intertubular material dominates the fracture behaviour of this tissue. The tubular components of the wall appear to reinforce against fracture along the weak plane and the entire wall organization provides the mechanical capability for limiting and controlling fracture in this tissue.

Animals↗

PubMedDate not supplied

Biomechanical comparison of two plating techniques for fixation of acetabular osteotomies in dogs.

OBJECTIVE: To compare the failure properties of a 5-hole, 2.7-mm curved acetabular plate (AP) to a 5-hole, 3.5-mm reconstruction plate (RP) when applied to acetabular osteotomies. STUDY DESIGN: Cadaver study. ANIMALS OR SAMPLE POPULATION: Pelves of 8 mature, large-breed dogs. METHODS: A 5-hole, 2.7-mm AP and a 5-hole, 3.5-mm RP were contoured and applied to the dorsal acetabulum of each pelvis. A central acetabular fracture was simulated after plate application by a transverse osteotomy with a fine saw. Each acetabulum was loaded in a weight-bearing direction. A load-deformation curve was produced for each construct, and biomechanical properties of the AP and RP were compared with the Student's paired t-test. A P value of < .05 was considered significant. RESULTS: For the AP and RP composite respectively, the mean +/- SD maximum load to failure was 2,721 +/- 632 N and 2,488 +/- 800 N, the stiffness was 4.8 +/- 1.8 N/m and 5.3 +/- 1.9 N/m, and the energy absorbed was 15.1 +/- 5.2 Nm and 16.3 +/- 8.3 Nm. None of these differences was statistically significant. CONCLUSIONS: Both fixation techniques provided comparable strength, stiffness, and energy absorbed under the loading conditions of this study. CLINICAL RELEVANCE: Because of the relative ease of application, the 2.7-mm curved AP may be the practical choice for acetabular fracture repair in large dogs.

Acetabulum↗

PubMedDate not supplied

Mechanical work as a determinant of prey-handling behavior in the tokay gecko (Gekko gecko).

In this study an in vitro analysis of the force and mechanical work required to bite prey items of different size and physical character is combined with an in vivo analysis of prey-handling behavior in the tokay gecko (Gekko gecko). The force required to bite and the work of biting increase with prey size, but the rate of increase is prey specific, with crickets (Acheta domestica) requiring substantially more force and work per bite than larvae (Galleria mellonella and Manduca sexta) for all but the smallest prey. Prey-handling behavior is also prey specific. Geckos exert more bites per feeding event on small crickets than on small insect larvae, but the number of bites increases faster with prey mass for larvae than for crickets. Combination of the in vitro mechanical measurements with the in vivo behavior analysis allows the calculation of total mechanical work per feeding event and indicates that total work increases with prey size but that the difference between prey types is far less than predicted from the differences in structural properties of the prey. This occurs because the number of bites and work per bite relationships tend to cancel the differences in the total work necessary to process each prey type. Thus, when considering the effect of prey size, a 13-fold greater rate of increase in bite force and an 18-fold greater rate of increase of work per bit for crickets over larvae was partially compensated for by a threefold increase in the number of bites used on larvae relative to crickets. These results can be interpreted in two ways. The effect of mechanical work in feeding behavior suggests that the energetics of jaw adductor musculature could play a greater role in governing the feeding behavior of this lizard than has previously been expected. Alternatively, the scaling of work in feeding over a range of prey sizes suggests distinct differences in the geometric features of the prey that determine how they are processed.

Animals↗