Search PubMed⌕ Search

Biomedical subjects

H Droschl

Publications and source records attributed to H Droschl.

At least 19 recordsLinked to original sources
PubMed2004

A comparative in vitro study of the strength of directly bonded brackets using different curing techniques.

The aim of this study was to compare, by shear testing, the bond strengths after 1 and 24 hours of a light-cured resin (Enlight) and a light-cured glass ionomer cement GIC (Fuji Ortho LC) using various polymerization lamps (halogen, high performance halogen, xenon, and diode) for the direct bonding of brackets. The self-curing resin (Concise) was used as the control. The analysis was carried out using the SPSS program. For group comparison purposes, the single factor variance analysis (ANOVA) and the post-hoc test (Tukey's HSD) were used. The level of significance was established at P < 0.05. When comparing two mean values the t-test for independent random samples was employed. All polymerization lamps achieved the minimum bond strength of 5-8 MPa. With Enlight LV, bond strength was dependent on curing time (the halogen lamp achieved the highest bond strength of 10.0 MPa, P < 0.001, with a curing time of 40 seconds. The other lamps showed similar results) and on the mode of cure (the highest bond strength values were achieved by four-sided curing, P= 0.04). Fuji Ortho LC, on the other hand, was independent of the duration of light curing and the type of lamp used. The bond strengths of the resin-modified glass ionomer cement (RMGIC) were similar to or somewhat higher than those achieved with light-cured composite resin (P = 0.039) when lamps with short polymerization times were used, but were significantly lower (P< 0.001) when compared with the self-curing composite adhesive. After 24 hours, the bond strengths of all adhesives showed a significant increase: Enlight 19 per cent, Fuji Ortho LC 6.6 per cent, Concise 16 per cent. Bond failure occurred for Enlight at the bracket-composite resin adhesive interface in 90 per cent and with Concise in 57 per cent. However, Fuji Ortho LC showed far more cohesive and mixed failures, indicating an improved bond between bracket and cement.

Adhesives↗
PubMed2004

A comparative study of polymerization lamps to determine the degree of cure of composites using infrared spectroscopy.

The aim of this study was to compare polymerization lamps of various technologies (halogen, high performance halogen, xenon, i.e. plasma arc, as well as diode lamps) to determine the degree of polymerization of composite probes using Fourier-transform infrared (FTIR) spectroscopy. To observe the light-induced curing reaction under a bracket, an attenuated total reflection (ATR)-FTIR was used. The results showed that the recommended curing times for all the polymerization lamps tested were adequate for successful polymerization of the composite used (degree of conversion approximately 60 per cent, which did not exceed 66 per cent after longer curing times). However, even after very long curing times, delayed curing of the composite must be taken into consideration as there was a decrease of approximately 10 per cent in FTIR band intensities (1637 and 3104 cm(-1)). ATR-FTIR spectroscopy showed that when bonding brackets with materials cured by light, uncured areas remain in the centre of the lowest layer of the adhesive.

Acrylic Resins↗
PubMed1996

Evaluation of continuous arch and segmented arch leveling techniques in adult patients--a clinical study.

The purpose of this study was to compare the efficacy of overbite correction achieved by a conventional continuous arch wire technique and the segmented arch technique as recommended by Burstone. The sample comprised 50 adult patients (age 18 to 40 years) with deep bites. Twenty-five patients were treated with a continuous arch wire technique (CAW); in the second half of the sample, the segmented arch technique (Burstone) was used for correction of the vertical malocclusion. Lateral cephalograms and plaster cast models taken before and immediately after treatment were evaluated. Statistical analysis was performed on the collected data. The results showed that both techniques produced a highly significant overbite reduction (CAW: -3.17 mm, p < 0.001; Burstone: -3.56 mm, p < 0.001). The CAW group showed an extrusion in the molar area with subsequent posterior rotation of the mandible (6occl-ML: +1.30 mm; 6occl-NSL: +1.63 mm; ML/NSL: +1.94 degrees, all p < 0.001). The Burstone group, however, showed overbite reduction by incisor intrusion without any substantial extrusion of posterior teeth (upper 1-NSL: -1.50 mm; lower 1-ML: -1.72 mm; both p < 0.001). As a consequence, no significant posterior rotation of the mandible took place (ML/NSL: +0.52 degrees, n.s.). It is concluded that in adult patients the segmented arch technique (Burstone) can be considered as being superior to a conventional continuous arch wire technique if arch leveling by incisor intrusion is indicated.

Adolescent↗
PubMed1992

[A new method for the quantitative and qualitative measurement of tooth movements].

A new method for the in vivo measurement of the movements of teeth is described. Measuring blocks are attached to brackets and tubes. Calibrated holes are drilled in each side of the blocks. Using an electronic sliding caliper, measurements are made in all three dimensions between moving teeth and blocks of anchored segments. With the aid of a computer programme, these measurements can be used to construct pictures of various teeth. By taking measurements at different stages of treatment, the movements of the teeth can be shown in three-dimensional images.

Adolescent↗
PubMed1992

[The orthodontic treatment of deep bite in adults--a comparison of the straight-wire appliance and the segmented arch technic].

The purpose of the study was to analyse and compare deep overbite correction in adult patients carried out by a straight wire appliance and the segmented arch technique as recommended by Burstone. The sample comprised 50 adult, deep bite patients, 25 each treated with straight wire appliance and segmented arch technique. Plaster casts and lateral cephalograms made before and immediately after finishing treatment were analysed. Both techniques were successful in overbite correction; overbite reduction amounted to 3 to 3.5 mm. The straight wire appliance group demonstrated predominantly molar extrusion and as a result posterior mandibular rotation. A slight intrusion of 1 mm was seen in the lower incisor area. The segmented arch technique resulted in an incisor intrusion of 1.5 mm in the upper and 1.7 mm in the lower jaw. No substantiate extrusion in the molar area was found. The advantages of this technique are discussed.

Adult↗
PubMed1992

Data and patterns of transverse dentofacial structure of 6- to 15-year-old children: a posteroanterior cephalometric study.

The aims of the present cross-sectional investigation were to provide normative data of selected dentofacial posteroanterior cephalometric measures and to describe the patterns of transverse dentofacial structure. The material comprised the P-A cephalograms of 588 Austrian schoolchildren (157 girls and 431 boys, who were 6 to 15 years old). All subjects were healthy, presented various types of occlusions, and did not receive orthodontic or orthopedic therapy. In studying the P-A cephalograms, 8 linear and 2 angular variables, as well as 10 ratios were used. The results of the study revealed that all skeletal widths and all ratios representing relations between the various breadths of the facial skeleton and the interorbital width demonstrated an increase when the measurements at the initial and final ages of 6 and 15 years, respectively, were compared. However, the maxillary intermolar width during the period from 9 to 12 years did not present any increase, and the mandibular intermolar width remained approximately the same during the whole observation period. The transverse dentoalveolar relationship in the incisal region remained very symmetric during aging. The standard deviations of most cephalometric variables were small when they were compared with their corresponding mean values. The present data are of value for the diagnosis of various types of dentofacial anomalies, for monitoring growth of persons or groups of corresponding age and race, and for comparison with other studies.

Adolescent↗
PubMed1991

[Anterior tooth intrusion with the base arch: preactivation by tip-back bending or curvature?].

Burstone's intrusion mechanics has been found to be effective in the treatment of a deep bite due to intrusion of the anterior teeth. The pre-activation of the intrusion arch by a tip-back bending shows a shortening in the activation. Measurements objectified the extent of the shortening and the resulting horizontal forces for TMA arches of a dimension of 0.017 x 0.025 inch relating to different distances between molars and anterior teeth and pre-activation by means of tip-back bending or curvature. The change of the vertical force in connection with a simulated intrusion of 5 mm was also registered. Clinical consequences of the therapy are discussed.

Cuspid↗
PubMed1991

[The tooth transplant in orthodontic treatment planning].

The analysis of all examined transplant cases combined treated with orthodontics shows a success rate of 76%. It must be underlined that the germ development at the time of the transplantation is of utmost importance. The best possible time proved to be at a root development of 2/3 to 3/4. Exact indication position, a careful atraumatic operation method and a short time of operation are also important factors of a successful transplantation. If all these preconditions are met, this method can be recommended.

Adolescent↗
PubMed1990

[The early treatment of progenia in the deciduous dentition compared to treatment in the mixed dentition].

The aim of this research was to examine the effect of the chin cap on mandibular prognathism (Angle class III) with or without a Fränkel appliance. 30 class III patients were examined. Head plates and casts made before and after active treatment were evaluated. The patients were divided into group I (initial X-ray incisivi decidui ID) and group II (initial X-ray incisivi permanentes IP). Group I (ID) showed a stronger skeletal response. Group II (IP) already showed more severe prognathic values in the initial X-rays. In group I (ID) a decrease of the gonial angle, SNB- and SNPog angle as well as an increase of both the ANB- and articulare angle were observed, however not in group II (IP) or at least not to the same extend. Overbite and overjet values reached the ideal values. In both groups dental compensation was observed.

Activator Appliances↗
PubMed1990

[The effect of the vertical bracket position on the orthodontic finish].

As during orthodontic treatment and in particular during the phase of the precise adjustment of occlusion by applying the "straight-wire technique" problems arise as far as the vertical dimensions are concerned, the usual distances between the bracket slots and the edges of the incisors respectively the top of the cusps have been verified. Measurements were done on models at the end of treatment of ten patients treated with fixed attachments who may represent ideal occlusion as far as profile radiographs and gnathology were concerned. After regulation of the plane of occlusion the vertical distances between the slot base plane (parallel to the plane of occlusion) and the edge of the incisors respectively tops of cusps were measured by means of a modified parallelometer in connection with a special slot and tube support as well as a specially developed dial test indicator, while a maximum fit between bracket base and buccal crown surface was given. In case of the upper front brackets (torque + 22 degrees) large vertical measurement to the edge of the incisors were recorded, 8.25 respectively 8.33 mm). This may be attributable to excessive torque of the applied brackets. Only approximate figures for the vertical positioning for other teeth could be given, as anatomical variations have to be considered.

Adolescent↗
PubMed1989

[The positioner--a possibility for the fine adjustment of the occlusion objectively assessed by condylar measurements of the discrepancy between the ICP and RCP].

A group of ten adolescents was treated with fixed appliances at the Department of Stomatology and Oral and Maxillofacial Surgery, Graz. Subsequently the patients were fitted with a gnathological positioner. On the day of band removal ten sets of models were made and subsequently two, four and twelve weeks later. They were mounted on an articulator and cephalometric measurements were taken three times by each of the examiners. These records served to provide evidence of discrepancies of the condylar position between ICP and RCP in all three planes. In the second part of the examination, the patients were instructed to wear the appliance at night for another year. Casting of models, mounting in articulators and condymetric measurements were repeated as above. After wearing the positioner for three months, we observed a definite improvement of the occlusion and a wide conformity of the RCP and ICP measurements. After one year of night-time retention there was a slight increase of the mean values. In addition, we could establish statistically that condymetric model measurements are independent of the examiner and the method employed.

Adolescent↗
PubMed1989

[New wires and their force delivery--consequences for orthodontic therapy].

Levelling arches made of stainless-steel wires were compared with nickel-titanium wires of the new generation which are distinguished by their shape memory, superelasticity and their excellent spring-back. The data received from a bending test have been analysed statistically and revealed a linear unloading curve of the twisted stainless-steel wires. The nickel-titanium wires, however, showed a clear deviation form the linearity with a curviform course. Besides the unusual unloading curve with a constant force mechanism in the middle range of deactivation the wires give off the same amount of force irrespective of the degree of activation (that is to say, regardless whether the level difference between the brackets amounts to 1 or to 4 mm). The diagram shows that the greater the activity between the brackets, the longer the period of superelasticity. Therefore the nickel-titanium wires are suited for large level differences or deflections. At a low activation rate the characteristic line takes a very steep and almost linear deactivation curve. In these cases twisted stainless steal wires should be preferred because of their lower load deflection rate and flexibility.

Dental Alloys↗
PubMed1989

[Periodontal development after tooth germ transplantation within the framework of orthodontic treatment].

The normal development of the periodontal structures was confirmed histologically on young beagle dogs following tooth germ transplants. In humans, clinical and radiographic examinations revealed no pathology of the periodontium following transplantation of tooth germs. The grafted teeth could be moved orthodontically in the same way as any other teeth. No precautions need to be taken. This paper describes the most common indications for transplanting the tooth germs of canines, bicuspids and molars.

Adolescent↗
PubMed1989

[Adhesive strength and bonding behavior in graphite-marked bracket positioning].

During a one-year observation period eleven patients treated with fixed appliances and 164 brackets which had been bonded in pairs, were checked at periodic intervals. Every patient had brackets positioned on the teeth in the first and fourth quadrant without graphite marking and in the second and third quadrant with graphite marking. In a parallel in-vitro study with eight pairs of teeth the above described conditions were applied. These specimens were examined in an universal testing machine in order to determine the magnitude of the shear forces. In the in-vivo as well as in the in-vitro study no statistically significant correlations were revealed between the graphite marking and the durability of adhesion as well as the required shear force of the examined brackets. Utilising light microscopy studies, the penetration of adhesive was determined in relation to the position of the graphite marking in etched enamel; at was harmlessness of the reference medium.

Acid Etching, Dental↗
PubMed1989

Changes in occlusion and condylar positioning during retention with a gnathologic positioner.

To investigate whether orthodontic cases can fulfil gnathologic requirement, models of 10 adolescent patients (of the Department of Orthodontics at the University Dental Clinic, Graz) were mounted in an articulator at band removal and 2, 4 and 12 weeks and one year later. During this year the patients wore a gnathologic positioner. Using a condymeter, discrepancies between RCP and ICP in three spatial planes were measured and the spatial diagonal computed. Statistical analysis showed a clear reduction of the means of slide in centric during continuous wearing of the positioner, after 3 months, RCP and ICP being almost identical. After a further 7 months, during which the positioner was worn only at night, the amount of slide increased again slightly. The increase of the spatial diagonal was due to an increase of the sagittal and vertical slides whereas the lateral slide remained constant.

Adolescent↗