Biomedical subjects

Guillermo A Ameer

Publications and source records attributed to Guillermo A Ameer.

12 recordsLinked to original sources

PubMed2006

A citric acid-based hydroxyapatite composite for orthopedic implants.

We describe a novel approach to process bioceramic microparticles and poly(diol citrates) into bioceramic-elastomer composites for potential use in orthopedic surgery. The composite consists of the biodegradable elastomer poly(1,8-octanediol-citrate) (POC) and the bioceramic hydroxyapatite (HA). The objective of this work was to characterize POC-HA composites and assess the feasibility of fabricating tissue fixation devices using machining and molding techniques. The mechanical properties of POC-HA composites with HA (40, 50, 60, 65wt.%) were within the range of values reported for tissue fixation devices (for POC-HA 65wt.%, S(b)=41.4+/-3.1, E(b)=501.7+/-40.3, S(c)=74.6+/-9.0, E(c)=448.8+/-27.0, S(t)=9.7+/-2.3, E(t)=334.8+/-73.5, S(s)=27.7+/-2.4, T(s)=27.3+/-4.9, all values in MPa). At 20 weeks, the weight loss of POC-HA composites ranged between 8 and 12wt.%, with 65wt.% HA composites degrading the slowest. Exposure of POC-HA to simulated body fluid resulted in extensive mineralization in the form of calcium phosphate with Ca/P of 1.5-1.7 similar to bone. POC-HA supported osteoblast adhesion in vitro and histology results from POC-HA samples that were implanted in rabbit knees for 6 weeks suggest that the composite is biocompatible. Synthesis of POC-HA is easy and inexpensive, does not involve harsh solvents or initiators, and the mechanical properties of POC-HA with 65wt.% HA are suitable for the fabrication of potentially osteoconductive bone screws.

Animals↗

PubMed2006

Spectroscopic translation of cell-material interactions.

The characterization of cellular interactions with a biomaterial surface is important to the development of novel biomaterials. Traditional methods used to characterize processes such as cellular adhesion and differentiation on biomaterials can be time consuming, and destructive, and are not amenable to quantitative assessment in situ. As the development of novel biomaterials shifts towards small-scale, combinatorial, and high throughput approaches, new techniques will be required to rapidly screen and characterize cell/biomaterial interactions. Towards this goal, we assessed the feasibility of using 4-dimensional elastic light-scattering fingerprinting (4D-ELF) to describe the differentiation of human aortic smooth muscle cells (HASMCs), as well as the adhesion, and apoptotic processes of human aortic endothelial cells (HAECs), in a quantitative and non-perturbing manner. HASMC and HAEC were cultured under conditions to induce cell differentiation, attachment, and apoptosis which were evaluated via immunohistochemistry, microscopy, biochemistry, and 4D-ELF. The results show that 4D-ELF detected changes in the size distributions of subcellular organelles and structures that were associated with these specific cellular processes. 4D-ELF is a novel way to assess cell phenotype, strength of adhesion, and the onset of apoptosis on a biomaterial surface and could potentially be used as a rapid and quantitative screening tool to provide a more in-depth understanding of cell/biomaterial interactions.

Biocompatible Materials↗

PubMed2006

Hemocompatibility evaluation of poly(glycerol-sebacate) in vitro for vascular tissue engineering.

Poly(glycerol-sebacate) (PGS) is an elastomeric biodegradable polyester that could potentially be used to engineer blood vessels in vivo. However, its blood-material interactions are unknown. The objectives of this study were to: (a) fabricate PGS-based biphasic tubular scaffolds and (b) assess the blood compatibility of PGS in vitro in order to get some insight into its potential use in vivo. PGS was incorporated into biphasic scaffolds by dip-coating glass rods with PGS pre-polymer. The thrombogenicity (platelet adhesion and aggregation) and inflammatory potential (IL-1beta and TNFalpha expression) of PGS were evaluated using fresh human blood and a human monocyte cell line (THP-1). The activation of the clotting system was assessed via measurement of tissue factor expression on THP-1 cells, plasma recalcification times, and whole blood clotting times. Glass, tissue culture plastic (TCP), poly(l-lactide-co-glycolide) (PLGA), and expanded polytetrafluorethylene (ePTFE) were used as reference materials. Biphasic scaffolds with PGS as the blood-contacting surface were successfully fabricated. Relative to glass (100%), platelet attachment on ePTFE, PLGA and PGS was 61%, 100%, and 28%, respectively. PGS elicited a significantly lower release of IL-1beta and TNFalpha from THP-1 cells than ePTFE and PLGA. Similarly, relative to all reference materials, tissue factor expression by THP-1 cells was decreased when exposed to PGS. Plasma recalcification and whole blood clotting profiles of PGS were comparable to or better than those of the reference polymers tested.

Biocompatible Materials↗

PubMed2006

Mechanical interlocking of engineered cartilage to an underlying polymeric substrate: towards a biohybrid tissue equivalent.

This study investigates the feasibility of engineering a biohybrid cartilage equivalent (BCE) with the long-term goal of restoring the mechanical integrity and interfacial characteristics of severely damaged cartilage. The BCE depends on the successful adhesion, via mechanical interlocking, of a cartilage layer to a nondegradable composite scaffold or prosthesis. The model scaffold, consisting of a nonwoven mesh bonded to a solid core, was seeded with bovine articular chondrocytes. High molecular weight poly(L-lactic acid), which has a slow degradation time, was used to model the nondegradable polymer. Biochemical and histological analysis demonstrate that the BCE can support the growth of a cartilaginous matrix for at least 6 weeks in culture. Mechanical testing of the BCE showed cartilage adhesion strength increased from 19.27+/-1.62 to 43.79+/-3.88 kPa between 35 and 50 days in culture. Nonmechanically interlocked cartilage achieved less than 5% of this adhesion strength. For the first time, atomic force microscopy (AFM) was used to characterize surface topography of tissue-engineered cartilage. Surface roughness of constructs after 8 and 10 weeks ranged from 153 to 171 nm, falling within the range of native cartilage (100-600 nm). This study demonstrates the feasibility of creating a biohybrid cartilage equivalent by mechanically interlocking a cartilaginous layer to an underlying polymeric matrix.

Animals↗

PubMed2006

A new biodegradable polyester elastomer for cartilage tissue engineering.

The objective of this study is to assess whether a new biodegradable elastomer, poly(1,8-octanediol citrate) (POC), would be a suitable material to engineer elastomeric scaffolds for cartilage tissue engineering. Porous POC scaffolds were prepared via the salt-leaching method and initially assessed for their ability to rapidly recover from compressive deformation (% recovery ratio). Controls consisted of scaffolds made from other materials commonly used in cartilage tissue engineering, including 2% agarose, 4% alginate, non woven poly(glycolic acid) (PGA) meshes, and non woven poly(L-lactide-co-glycolide) (PLGA) meshes. Articular chondrocytes from bovine knee were isolated and seeded onto porous disk-shaped POC scaffolds, which were subsequently cultured in vitro for up to 28 days. POC scaffolds completely recover from compressive deformation, and the stress-strain curve is typical of an elastomer (recovery ratio>98%). Agarose gel (2%) scaffolds broke during the compression test. The recovery ratio of 4% alginate gel scaffolds, PLLA, and PGA were 72, 85, and 88%, respectively. The Young's modulus of POC-chondrocyte constructs and cell-free POC scaffolds cultured for 28 days were 12.02+/-2.26 kPa and 3.27+/-0.72 kPa, respectively. After 28 days of culture, the recovery ratio of POC-chondrocyte constructs and cell-free POC scaffolds were 93% and 99%, respectively. The glycosaminoglycan (GAG) and collagen content at day 28 was 36% and 26% of that found in bovine knee cartilage explants. Histology/immunohistochemistry evaluations confirm that chondrocytes were able to attach to the pore walls within the scaffold, maintain cell phenotype, and form a cartilaginous tissue during the 28 days of culture.

Absorbable Implants↗

PubMed2006

Biomechanical characterization of vaginal versus abdominal surgical wound healing in the rabbit.

OBJECTIVE: The objective of the study was to compare biomechanical properties of vaginal versus abdominal surgical wound healing in the rabbit. STUDY DESIGN: Bilateral 6-mm full-thickness circular segments were excised from the vagina and abdominal skin in 38 New Zealand White female rabbits. Animals were killed 0, 4, 7, 10, 14, 21, 28, and 35 days after wounding, and the wounds were assessed for surface area and tensile properties. RESULTS: Wound closure and scar contraction were significantly faster in the vagina than the abdomen (P = .001). Baseline tensile strength (P = .05), modulus (P = .001), and tensile energy to break (P = .18) were higher in the abdomen, whereas maximal tissue elongation was higher in the vagina (P = .13). After wounding, a drop in tensile strength, modulus, and tensile energy to break was observed in both tissues through postwounding day 4, followed by a progressive recovery of these properties. A progressive loss of elasticity was noted in both tissues after wounding. CONCLUSION: The surgical wound closes and contracts faster in the rabbit vagina than in its abdomen. Although these tissues have different biomechanical properties at baseline, they regenerate their tensile strength and lose their elasticity at a similar rate.

Abdomen↗

PubMed2005

Synthesis and evaluation of poly(diol citrate) biodegradable elastomers.

Herein, we report the synthesis and evaluation of a novel family of biodegradable and elastomeric polyesters, poly(diol citrates). Poly(diol citrates) were synthesized by reacting citric acid with various diols to form a covalent cross-linked network via a polycondensation reaction without using exogenous catalysts. The tensile strength of poly(diol citrates) were as high as 11.15+/-2.62 MPa and Young's modulus ranged from 1.60+/-0.05 to 13.98+/-3.05 MPa under the synthesis conditions that were investigated. Elongation was as high as 502+/-16%. No permanent deformation was found during mechanical tests. The equilibrium water-in-air contact angles of measured poly(diol citrates) films ranged from 15 degrees to 53 degrees . The mechanical properties, degradation and surface characteristics of poly(diol citrates) could be controlled by choosing different diols as well as by controlling the cross-link density of the polyester network. Various types of poly(diol citrate) scaffolds were fabricated to demonstrate their processing potential. These scaffolds were soft and could recover from deformation. In vitro and in vivo evaluation using cell culture and subcutaneous implantation, respectively, confirmed cell and tissue compatibility. The introduction of poly(diol citrates) will expand the repertoire of currently available biodegradable polymeric elastomers and should help meet the requirements of tissue engineering applications.

Animals↗

PubMed2005

Assessment of the stability of an immunoadsorbent for the extracorporeal removal of Beta-2-microglobulin from blood.

BACKGROUND: Dialysis-related amyloidosis (DRA) is a devastating and costly condition that affects patients with end stage kidney disease. A key feature of DRA is the formation of amyloid fibrils, consisting primarily of beta2-microglobulin. Except for kidney transplantation, conventional kidney replacement therapies, which are based on nonspecific mechanisms, do not adequately address beta2-microglobulin removal. An antihuman beta2-microglobulin single-chain variable region antibody fragment (scFv) was developed to confer specificity to beta2-microglobulin removal during hemodialysis. METHODS: The scFv was immobilized onto agarose and characterized for beta2m binding capacity, thermal stability at 37 degrees C, regeneration capacity, storage conditions, and sterility. RESULTS: The beta2-microglobulin binding capacity was 1.3 mg/ml scFv gel. The immunoadsorbent is thermally stable, can be regenerated, stored short-term in 20% ethanol, lyophilized for long-term storage, and withstand process conditions similar to that of a patient's hemodialysis therapy. CONCLUSIONS: The results support further investigation of immobilized scFvs as a novel tool to remove beta2-microglobulin from blood.

Amyloidosis↗

PubMed2004

Single-chain antibody fragment-based adsorbent for the extracorporeal removal of beta2-microglobulin.

BACKGROUND: Dialysis-related amyloidosis (DRA) is a frequent complication of end-stage renal disease (ESRD) that has been associated with the accumulation of beta2-microglobulin (beta2-m). Removal of beta2-m results in the loss of important proteins due to the nonspecific nature of current therapies. Although whole antibodies can potentially be used to confer specificity to beta2-m removal from blood, single-chain variable region (scFv) antibody fragments could potentially offer several advantages as immunoadsorption ligands due to their size, genetic definition, ability to be expressed by microbes, and amenability for in vitro evolution. METHODS: An antihuman beta2-m scFv was constructed from the BBM.1 hybridoma and expressed by a yeast display vector. The binding affinity of the wild-type scFv fragment was quantified by flow cytometry analysis. Soluble scFv was expressed by a yeast secretion vector, purified, and immobilized onto agarose beads. The binding capacity of the immunoadsorbent was measured by equilibrating samples with saturating quantities of fluorescent beta2-m in serum. RESULTS: The displayed scFv possessed a nanomolar affinity (KD= 0.008 +/- 0.004 mg-beta2-m/L). The immunoadsorbent exhibited an adsorption site density of 0.41 +/- 0.01 mg beta2-m/mL settled gel. Under saturating conditions, the mass ratio of adsorbed beta2-m to immobilized antibody is 70% greater than any previous literature report for whole antibodies. Preliminary specificity experiments suggest that the scFv-based immunoadsorbent is specific toward human beta2-m. CONCLUSION: Recombinant DNA technology was successfully used to engineer an scFv-based immunoadsorbent. Use of immobilized scFvs during hemodialysis may minimize loss of valuable proteins and facilitate the removal of macromolecules that are significantly larger than the molecular weight cut-off of the membrane.

Amino Acid Sequence↗

PubMed2004

Biodegradable polyester elastomers in tissue engineering.

Tissue engineering often makes use of biodegradable scaffolds to guide and promote controlled cellular growth and differentiation in order to generate new tissue. There has been significant research regarding the effects of scaffold surface chemistry and degradation rate on tissue formation and the importance of these parameters is widely recognised. Nevertheless, studies describing the role of mechanical stimuli during tissue development and function suggest that the mechanical properties of the scaffold will also be important. In particular, scaffold mechanics should be taken into account if mechanical stimulation, such as cyclic strain, will be incorporated into strategies to grow improved tissues or the target tissue to be replaced has elastomeric properties. Biodegradable polyesters, such as polyglycolide, polylactide and poly(lactide-co-glycolide), although commonly used in tissue engineering, undergo plastic deformation and failure when exposed to long-term cyclic strain, limiting their use in engineering elastomeric tissues. This review will cover the latest advances in the development of biodegradable polyester elastomers for use as scaffolds to engineer tissues, such as heart valves and blood vessels.

Animals↗

PubMed2002

A tough biodegradable elastomer.

Biodegradable polymers have significant potential in biotechnology and bioengineering. However, for some applications, they are limited by their inferior mechanical properties and unsatisfactory compatibility with cells and tissues. A strong, biodegradable, and biocompatible elastomer could be useful for fields such as tissue engineering, drug delivery, and in vivo sensing. We designed, synthesized, and characterized a tough biodegradable elastomer from biocompatible monomers. This elastomer forms a covalently crosslinked, three-dimensional network of random coils with hydroxyl groups attached to its backbone. Both crosslinking and the hydrogen-bonding interactions between the hydroxyl groups likely contribute to the unique properties of the elastomer. In vitro and in vivo studies show that the polymer has good biocompatibility. Polymer implants under animal skin are absorbed completely within 60 days with restoration of the implantation sites to their normal architecture.

3T3 Cells↗

PubMedDate not supplied

Novel biphasic elastomeric scaffold for small-diameter blood vessel tissue engineering.

Compliance mismatch, thrombosis, and long culture times in vitro remain important challenges to the clinical implementation of a tissue-engineered small-diameter blood vessel (SDBV). To address these issues, we are developing an implantable elastomeric and biodegradable biphasic tubular scaffold. The scaffold design uses connected nonporous and porous phases as a basis to mimic, respectively, the intimal and medial layers of a blood vessel. Biphasic scaffolds were fabricated from poly(diol citrate), a novel class of biodegradable polyester elastomer. Scaffolds were characterized for tensile and compressive properties, burst pressure, compliance, foreign body reaction (via subcutaneous implantation in rats), and cell distribution and differentiation (via histology, scanning electron microscopy, and immunohistochemistry). Tensile tests, burst pressure, and compliance measurements confirm that the incorporation of a nonporous phase to create a "skin" connected to the porous phase of a scaffold can provide bulk mechanical properties that are similar to those of a native vessel. Compression tests confirm that the scaffolds are soft and recover from deformation. Subcutaneously implanted poly(diol citrate) porous scaffolds produce a thin fibrous capsule and allow for tissue ingrowth. In vitro culture of tubular biphasic scaffolds seeded with human aortic smooth muscle cells (HASMCs) and endothelial cells (HAECs) demonstrates the ability of this design to support cell compartmentalization, coculture, and cell differentiation. The newly formed HAEC monolayer stained positive for von Willebrand factor whereas collagen- and calponin-positive HASMCs were present in the porous phase.

Animals↗