Search PubMed⌕ Search

Biomedical subjects

G Bateman

Publications and source records attributed to G Bateman.

6 recordsLinked to original sources
PubMed2006

Ectopia or concomitant hypohyperdontia? A case report.

This report describes the unusual appearance seen on a panoramic radiograph of an orthodontic patient which the authors argue may represent ectopia or concomitant hypohyperdontia of the mandibular premolar teeth. A literature review describes the frequency of such anomalies in this area from previous studies. The presenting features of the patient and the differential diagnoses are explored. Treatment planning is discussed and treatment carried out in this particular case is detailed. The unusual symmetrical bilateral anomalies in this patient may point to a genetic determinant of tooth germ position and/or movement.

Anodontia↗
PubMed2005

An investigation into the bonding of orthodontic attachments to porcelain.

This study assessed bonding of orthodontic brackets to porcelain teeth using two different surface preparation techniques and comparing two bonding systems, Fuji Ortho L.C. and Transbond. Four groups of 20 porcelain premolar teeth were bonded with metal orthodontic brackets (0.022 inch Minitwin, 3M Unitek) according to the following protocol: Transbond with a phosphoric acid etch (group 1), Transbond with a hydrofluoric acid etch (group 2), Fuji Ortho L.C. with a hydrofluoric acid etch (group 3), and Fuji Ortho L.C. with a phosphoric acid etch (group 4). All groups were bonded with a silane coupling agent. The teeth were debonded with an Instron universal testing machine. Bond strength, site of bond failure and adhesive remnant index (ARI) were recorded for each group. Differences between groups were analysed statistically. The composite resin groups (groups 1 and 2) had the highest mean bond strength values at 7.9 and 9.7 MPa, respectively. The resin-modified glass ionomer cement groups (RMGIC; groups 3 and 4) had the lowest mean bond strength values at 6.3 and 1.8 MPa, respectively. The mean bond strength of group 3 was significantly lower than all other groups (P < 0.0001). The Fuji groups had also significantly (P < 0.001) lower ARI scores than the composite groups (groups 1 and 2). Most samples experienced porcelain surface damage, except group 4. In conclusion, the highest bond strength levels were achieved with a conventional composite resin cement (groups 1 and 2). No significant differences in bond strength were found between the hydrofluoric and phosphoric acid etch technique.

Acid Etching, Dental↗
PubMed2003

Fibre-based post systems: a review.

OBJECTIVES: This article presents a review of published literature examining fibre-based endodontic post systems. DATA SOURCES: A MEDLINE search was carried out for any articles in dental journals pertaining to fibre-based post systems. Wherever possible articles cited were obtained from the journals and where this was not possible abstracts were obtained. Where no abstract was available the article was not considered for evaluation. DATA EXTRACTION: Articles were reviewed by a single observer and subject to meeting inclusion criteria were included in the review. Fifty-nine articles were considered suitable for inclusion. DATA SYNTHESIS: Articles were divided into categories and a subjective description of the articles was made. CONCLUSIONS: Review indicated that (1) most published literature on fibre-based posts took the form of laboratory analyses; (2) evidence for carbon-fibre posts far exceeds that for quartz-fibre posts; (3) laboratory evidence was contradictory and could not be used to inform practice reliably; (4) few clinical studies have been carried out though these have suggested fibre based posts may be clinically appropriate for restoration of the endodontically treated tooth; and (5) controlled prospective clinical trials evaluating fibre-based posts should be undertaken to inform use for clinical practice.

Carbon↗
PubMed1999

A new method for the quantitative analysis of endodontic microleakage.

The aim of this in vitro study was to evaluate the apical seal obtained with three commonly used root canal sealing cements: Sealapex, AH Plus or Topseal, and Sealite, using a new method based on the quantitative analysis of 125I-radiolabeled lysozyme penetration. One hundred thirteen teeth with straight single root canals were instrumented to master apical point #25/30. These were divided into three groups: (i) negative control (4 roots) covered with two layers of nail polish, (ii) test group (105 roots) obturated by laterally condensed guttapercha with the three cements; and (iii) positive control (4 roots) obturated without cement. The groups were then immersed in 125I lysozyme solution for a period of 1, 7, 14, or 28 days. After removal, six sections of 0.8 mm length each were made of each root with a fine diamond wire. Each section was analyzed for activity by a gamma counter, corrected for decay, and used to quantify protein penetration. Leakage was high in the positive control and almost negligible in the negative control. AH Plus (Topseal) and Sealapex showed similar leakage behavior over time, with AH Plus (Topseal) performing better. Sealite showed acceptable leakage up until day 14, after which a large increase occurred, presumably due to three-dimensional instability.

Calcium Hydroxide↗
PubMed1999

Dynamic and cyclic fatigue of engine-driven rotary nickel-titanium endodontic instruments.

The absence of adequate testing standards for engine-driven nickel-titanium (NiTi) instruments necessitates further study of these instruments in all areas. This study examined three groups of engine-driven rotary NiTi endodontic instruments (Profile, Hero, and Quantec) and assessed the times for dynamic fracture in relation to the radius of curvature to which the instruments were subjected during preparation, with the instrument diameter determined by size and taper and the mode by which the fracture occurred. Ten instruments were randomly selected representing each size and taper for each group and for each radius of curvature: 600 in total. The instruments were rotated at 350 rpm and introduced into a tempered steel curve that simulated a canal. Two radii of curvature of canals were used: 5 and 10 mm. Time at fracture was noted for all files, and the fracture faces of each file were analyzed with scanning electron microscopy. Radius of curvature was found to be the most significant factor in determining the fatigue resistance of the files. As radius of curvature decreased, fracture time decreased. Taper of files was found to be significant in determining fracture time. As diameter increased, fracture time decreased. In all cases, fracture was found to be of a ductile nature, thus implicating cyclic fatigue as a major cause of failure and necessitating further analyses and setting of standards in this area.

Dental High-Speed Technique↗