Search PubMed⌕ Search

Biomedical subjects

G A Somorjai

Publications and source records attributed to G A Somorjai.

15 recordsLinked to original sources
PubMed2006

Carbon monoxide adsorption and oxidation on monolayer films of cubic platinum nanoparticles investigated by infrared-visible sum frequency generation vibrational spectroscopy.

The adsorption and oxidation of CO on monolayer films of cubic Pt nanoparticles synthesized by a modified solution-phase polyol process were examined by sum frequency generation (SFG) vibrational spectroscopy in total internal reflection (TIR) geometry. Extremely low incident laser power (approximately 5 microJ/pulse of infrared) yields sufficient SFG intensity in TIR geometry and reduces destructive interference. Because TIR-SFG spectroscopy does not require correction for bulk gas absorption, CO spectra can be collected over a wide pressure range (<1 mTorr up to 700 Torr). Poly(vinylpyrrolidone)-capped Pt nanoparticles deposited on single-crystal sapphire were monitored under high-pressure reaction conditions in a combined spectroscopy-catalytic reactor cell. The effect of the capping polymer on the position and intensity of the CO peak was studied before and after low-temperature calcination. The polymer decreased the amount of CO adsorption and caused a slight red-shift of the atop CO band relative to a surface treated in oxygen at 373 K. Oxidation rates were determined by measuring the intensity of the atop CO peak as a function of time in the presence of flowing oxygen. The activation energy (approximately 19.8 kcal/mol) determined from the SFG data is close to that obtained from gas chromatography (GC) measurements of CO oxidation rates at different temperatures. The SFG and GC results are in good agreement with published data for Pt(100) surfaces.

Journal Article↗
PubMed2005

Entropically mediated polyolefin blend segregation at buried sapphire and air interfaces investigated by infrared-visible sum frequency generation vibrational spectroscopy.

The segregation behavior of binary polymer blends at hydrophilic solid sapphire and air interfaces was investigated by infrared-visible sum frequency generation (SFG) vibrational spectroscopy. SFG spectra were collected from a bulk miscible blend consisting of identical molecular weight (approximately 54,000) and similar surface free energy (29-35 dyn/cm) components of atactic polypropylene (aPP) and aspecific poly(ethylene-co-propylene) rubber (aEPR). Characteristic CH resonances of the blend were contrasted with those of the individual components at both buried (sapphire/polymer) and free (air/polymer) interfaces. Preferential segregation of the aPP component was observed after annealing at both air/polymer and sapphire/polymer interfaces. SFG spectra revealed ordering of the polymer backbone segments with the methylene (CH2) groups perpendicular to the surface at the sapphire interface and the methyl (CH3) groups upright at the air interface. The SFG results indicate that the surface composition can be determined from the peak intensities that are characteristic of each component and that conformational entropy played a likely role in surface segregation. aPP occupied a smaller free volume at the surface because of a statistically smaller segment length (aPP is more flexible and has a shorter length). In addition, the high density of the ordered CH3 side branches enhanced the surface activity by allowing the long-chain backbone segments of aPP to order at the surface.

Journal Article↗
PubMed2005

Molecular restructuring at poly(n-butyl methacrylate) and poly(methyl methacrylate) surfaces due to compression by a sapphire prism studied by infrared-visible sum frequency generation vibrational spectroscopy.

Infrared-visible sum frequency generation (SFG) vibrational spectroscopy, performed in visible wavelength total internal reflection (TIR) geometry, was used to determine the molecular structures of poly(n-butyl methacrylate) (PBMA) and poly(methyl methacrylate) (PMMA) surfaces in air and in contact with a smooth sapphire surface with and without the application of pressure. C-H vibrational resonances were probed optically to nondestructively examine the buried polymer/sapphire interfaces and obtain information about the molecular orientation in situ. These findings are contrasted with those of the same polymers cast from a toluene solution directly on the sapphire prism surface and annealed. Compared to polymer surface conformation in air, the SFG spectra of the deformed (compressed) PBMA at the sapphire interface illustrate that the ester butyl side chain restructures and tilts away from the surface normal. However, the molecular conformation in the similarly deformed PMMA at the sapphire interface is identical to that obtained in air, which is dominated by the upright-oriented ester methyl side chains. For PBMA and PMMA spin cast on sapphire and annealed, the surface structure of the undeformed PBMA at the sapphire interface is identical to that of the deformed PBMA at the sapphire interface, while the PMMA conformation is different and shows alpha-methyl group ordering. Since the glass transition temperature of PBMA is below room temperature, the rubbery state of PBMA demonstrates a melt-like behavior, evidenced by the fact that PBMA is in conformation chemical equilibrium at the sapphire surface even under compression. Due to the high glass transition temperature of PMMA, compression freezes PMMA in a metastable state, revealed by the restructured molecular conformation when annealed against the sapphire surface. The results of this study demonstrate that structural changes at buried polymer surfaces due to the application of contact pressure can be detected in situ by TIR-SFG vibrational spectroscopy.

Journal Article↗
PubMed2005

High-surface-area catalyst design: Synthesis, characterization, and reaction studies of platinum nanoparticles in mesoporous SBA-15 silica.

Platinum nanoparticles in the size range of 1.7-7.1 nm were produced by alcohol reduction methods. A polymer (poly(vinylpyrrolidone), PVP) was used to stabilize the particles by capping them in aqueous solution. The particles were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). TEM investigations demonstrate that the particles have a narrow size distribution. Mesoporous SBA-15 silica with 9-nm pores was synthesized by a hydrothermal process and used as a catalyst support. After incorporation into mesoporous SBA-15 silica using low-power sonication, the catalysts were calcined to remove the stabilizing polymer from the nanoparticle surface and reduced by H2. Pt particle sizes determined from selective gas adsorption measurements are larger than those determined by bulk techniques such as XRD and TEM. Room-temperature ethylene hydrogenation was chosen as a model reaction to probe the activity of the Pt/SBA-15 materials. The reaction was shown to be structure insensitive over a series of Pt/SBA-15 materials with particle sizes between 1.7 and 3.6 nm. The hydrogenolysis of ethane on Pt particles from 1.7 to 7.1 nm was weakly structure sensitive with smaller particles demonstrating higher specific activity. Turnover rates for ethane hydrogenolysis increased monotonically with increasing metal dispersion, suggesting that coordinatively unsaturated metal atoms present in small particles are more active for C2H6 hydrogenolysis than the low index planes that dominate in large particles. An explanation for the structure sensitivity is suggested, and the potential applications of these novel supported nanocatalysts for further studies of structure-activity and structure-selectivity relationships are discussed.

Journal Article↗
PubMed2005

Vibrational properties of CO at the Pt(111)-solution interface: the anomalous Stark-tuning slope.

Vibrational properties of CO have been studied on Pt(111) in acid and alkaline electrolytes by synchronous measurements of CO oxidation current (0.5 mV/s) and IRAS spectra (one spectrum for every 1 mV). We found that in acid solutions the frequency-tuning rate (dnu(CO)/dE) as well as the potential-dependent bandwidth (dDeltanu1/2/dE) deviates from expected linear relationships. This unusual potential-dependent behavior is interpreted in terms of compression/dissipation of CO islands during the CO oxidation, engendered by competitive adsorption between inactive anions from a supporting electrolyte and the reactive OH species.

Carbon Monoxide↗
PubMed2005

Fabrication of large number density platinum nanowire arrays by size reduction lithography and nanoimprint lithography.

Large number density Pt nanowires with typical dimensions of 12 microm x 20 nm x 5 nm (length x width x height) are fabricated on planar oxide supports. First sub-20 nm single crystalline silicon nanowires are fabricated by size reduction lithography, and then the Si nanowire pattern is replicated to produce a large number of Pt nanowires by nanoimprint lithography. The width and height of the Pt nanowires are uniform and are controlled with nanometer precision. The nanowire number density is 4 x 10(4) cm(-1), resulting in a Pt surface area larger than 2 cm(2) on a 5 x 5 cm(2) oxide substrate. Bimodal nanowires with different width have been generated by using a Pt shadow deposition technique. Using this technique, alternating 10 and 19 nm wide nanowires are produced.

Journal Article↗
PubMed2005

Parallel fabrication of sub-50-nm uniformly sized nanoparticles by deposition through a patterned silicon nitride nanostencil.

Using low-pressure chemical vapor deposition of silicon dioxide, we have reduced the size of 56-nm features in a silicon nitride membrane, called a stencil, down to 36 nm. Sub-50-nm uniformly sized nanoparticles are fabricated by electron-beam deposition of Pt through the stencil mask. A self-assembled monolayer (SAM) of tridecafluoro-1,1,2,2-tetrahydrooctyl-1-trichlorosilane was used to reduce Pt clogging of the nanosize holes during deposition as well as to protect the stencil during the postdeposition Pt removal. X-ray photoelectron spectroscopy shows that the SAM protects the stencil efficiently during this postdeposition removal of Pt.

Electrons↗
PubMed2001

Potential-dependent vibrational spectroscopy of solvent molecules at the Pt(111) electrode in a water/acetonitrile mixture studied by sum frequency generation.

Sum frequency generation (SFG) vibrational spectra of D(2)O and/or acetonitrile (CH(3)CN) on a Pt(111) single-crystal electrode were obtained as a function of applied potential in a 5 mol % water/acetonitrile mixed solvent with different 0.1 molar MSO(3)CF(3) salts (M = H(+), Li(+), Na(+), K(+), and Cs(+)). The results provide a very specific model for the composition of the inner Helmholtz layer as a function of potential and surface charge. Acetonitrile dominates the inner layer with the CN group directed toward the metal at potentials where the metal has a positive charge. As the surface becomes negatively charged, the acetonitrile orientation flips 180 degrees, with the CH(3) group pointing toward the surface. At even more negative surface charge, D(2)O displaces acetonitrile from the inner layer and is the predominant molecule on the surface. Here water is present as an oriented molecule with the oxygen end pointing toward the metal. The potential (and surface charge) where water is the dominant molecule in the inner Helmholtz layer is determined by the solvation energy of the cation.

Journal Article↗
PubMed2001

Structure and dynamics of dense monolayers of no adsorbed on Rh(111) in equilibrium with the gas phase in the Torr pressure range.

Using scanning tunneling microscopy, we show the phase transition between new structures of NO on Rh(111) in equilibrium with the gas phase near 300 K, in the Torr pressure range. Two phases with (2 x 2) and (3 x 3) periodicity transform into each other as the pressure and temperature change around the equilibrium P-T line. By measuring P and T at coexistence, we determined the heat of adsorption in the (3 x 3) structure. From the phase boundary dynamics, the activation energy barrier between phases were estimated. The results demonstrate that unique information can be obtained from high-pressure and high-temperature studies.

Journal Article↗
PubMed2001

Polymer surface science.

Molecular level studies of the structure and mechanical properties of polymer surfaces have been carried out by sum frequency generation (SFG) surface vibrational spectroscopy and atomic force microscopy (AFM). The surfaces of different grades of polyethylene and polypropylene have been characterized-including during the glass transition and when mechanically stretched. Copolymers that have hard and soft segments with different glass transition temperatures show phase separation, an effect of hydrogen bonding between the hard and soft segments, that influences their adhesive and friction properties. AFM and SFG show that low surface energy additives migrate to the surface and alter the surface mechanical properties. Polymers, where the chemical nature of the end groups is different from the backbone, show surface segregation of the hydrophobic part of the chain in air and the hydrophilic part in water. Likewise, in miscible polymer blends, surface segregation of the more hydrophobic component in air and the more hydrophilic component in water is observed. This area of surface science requires increased attention because of the predominance of polymers as structural materials and as biomaterials.

Biocompatible Materials↗
PubMed2001

Friction studies of hydrogel contact lenses using AFM: non-crosslinked polymers of low friction at the surface.

The surface of soft contact lenses made of crosslinked poly(2-hydroxyethyl methacrylate). pHEMA, has been investigated with atomic force microscopy in contact mode. The friction force and adhesive force measurements were able to differentiate the non-crosslinked pHEMA chains from the surface of the crosslinked pHEMA networks. These non-crosslinked pHEMA chains at the surface were anchored to the crosslinked pHEMA network, most likely by entanglement and their surfaces were about 2-4nm higher than the surrounding surface in a dehydrated state. In saline solution, the surface friction and adhesive force of the contact lens were significantly reduced compared to those measured for the surface-dehydrated contact lens.

Adhesiveness↗
PubMed2001

Catalysis research of relevance to carbon management: progress, challenges, and opportunities.

The goal of the "Opportunities for Catalysis Research in Carbon Management" workshop was to review within the context of greenhouse gas/carbon issues the current state of knowledge, barriers to further scientific and technological progress, and basic scientific research needs in the areas of H2 generation and utilization, light hydrocarbon activation and utilization, carbon dioxide activation, utilization, and sequestration, emerging techniques and research directions in relevant catalysis research, and in catalysis for more efficient transportation engines. Several overarching themes emerge from this review. First and foremost, there is a pressing need to better understand in detail the catalytic mechanisms involved in almost every process area mentioned above. This includes the structures, energetics, lifetimes, and reactivities of the species thought to be important in the key catalytic cycles. As much of this type of information as is possible to acquire would also greatly aid in better understanding perplexing, incomplete/inefficient catalytic cycles and in inventing new, efficient ones. The most productive way to attack such problems must include long-term, in-depth fundamental studies of both commercial and model processes, by conventional research techniques and, importantly, by applying various promising new physicochemical and computational approaches which would allow incisive, in situ elucidation of reaction pathways. There is also a consensus that more exploratory experiments, especially high-risk, unconventional catalytic and model studies, should be undertaken. Such an effort will likely require specialized equipment, instrumentation, and computational facilities. The most expeditious and cost-effective means to carry out this research would be by close coupling of academic, industrial, and national laboratory catalysis efforts worldwide. Completely new research approaches should be vigorously explored, ranging from novel compositions, fabrication techniques, reactors, and reaction conditions for heterogeneous catalysts, to novel ligands and ligation geometries (e.g., biomimetic), reaction media, and activation methods for homogeneous ones. The interplay between these two areas involving various hybrid and single-site supported catalyst systems should also be productive. Finally, new combinatorial and semicombinatorial means to rapidly create and screen catalyst systems are now available. As a complement to the approaches noted above, these techniques promise to greatly accelerate catalyst discovery, evaluation, and understanding. They should be incorporated in the vigorous international research effort needed in this field.

Journal Article↗
PubMed1985

Correlation between catalytic activity and bonding and coordination number of atoms and molecules on transition metal surfaces: Theory and experimental evidence.

Correlation between catalytic activity and low-energy local electronic fluctuations in transition metals is proposed. A theory and calculations are presented which indicate that maximum electronic fluctuations take place at high-coordination metal sites. Either (i) atomically rough surfaces that expose to the reactant molecules atoms with large numbers of nonmagnetic or weakly magnetic neighbors in the first or second layer at the surface or (ii) stepped and kinked surfaces are the most active in carrying out structure-sensitive catalytic reactions. The synthesis of ammonia from N(2) and H(2) over iron and rhenium surfaces, (1)H(2)/(2)H(2) exchange over stepped platinum crystal surfaces at low pressures, and the hydrogenolysis (C-C bond breaking) of isobutane at kinked platinum crystal surfaces are presented as experimental evidence in support of the theory.

Journal Article↗
PubMed1982

Photodissociation of water by p- and n-type polycrystalline iron oxides by using visible light (</=2.7 eV) in the absence of external potential.

A polycrystalline p/n diode assembly, consisting of pressed magnesium- and silicon-doped iron oxide powders, has been shown to photodissociate water by using visible light in the absence of any external potential. In the investigated pH range (8-14) the device produces hydrogen catalytically in amounts that are readily detectable by gas chromatography. The relatively low-power conversion efficiency of 0.05% is believed to be due to the poor change-transfer properties of the p-type iron oxide used.

Journal Article↗