Search PubMed⌕ Search

Biomedical subjects

F Devlieghere

Publications and source records attributed to F Devlieghere.

At least 37 records · Page 2Linked to original sources
PubMed2005

Factors affecting the inactivation of micro-organisms by intense light pulses.

AIM: To determine the influence of several factors on the inactivation of micro-organisms by intense light pulses (ILP). METHODS AND RESULTS: Micro-organisms on agar media were flashed 50 times under different conditions and their inactivation measured. Micro-organisms differed in sensitivity to ILP but no pattern was observed among different groups. Several enumeration methods to quantify the effect of ILP were investigated and showed relevant differences, shading effect and photoreactivation accounted for them, the strike method yielded the most reliable results. Higher decontamination efficiencies were obtained for Petri dishes located close to the strobe and inside the illumination cone. Decontamination efficacy decreased significantly at contamination levels >6.85 log(10). After 13 successive treatments, no resistance to ILP could be demonstrated. Media warming up depended on the distance from the strobe and the number of flashes. CONCLUSIONS: For an industrial implementation: the position and orientation of strobes in an unit will determine the lethality, products should be flashed as soon as possible after contamination occurs, a cooling system should be used for heat-sensitive products and flashed products should be light protected. No resistant flora is expected to develop. SIGNIFICANCE AND IMPACT OF THE STUDY: Conclusions derived from this work will allow a better implementation of this decontamination technique at industrial level.

Bacteria↗
PubMed2005

Environmental factors influencing the relationship between optical density and cell count for Listeria monocytogenes.

AIMS: The effect of temperature (2-30 degrees C), pH (4.8-7.4) and water activity (0.946-0.995) on the relationship between optical density (OD) at 600 nm and the plate count (CFU ml(-1)) was investigated for Listeria monocytogenes. METHODS AND RESULTS: Calibration curves, relating OD with plate counts, were collected by measuring the OD of consecutive one-half dilution series, before determining the cell density by classic plate count methods. The calibration curves were observed to be shifting in a parallel way, with increasing stress levels. Especially pH influenced the curve in a great extent, while the other variables were showing more synergetic effects. The reason for the shift was investigated by a microscopic viability test, showing a viability decrease with increasing stress levels, causing the shift of the calibration curve. In a last step a model was made describing the effect of environmental factors on the calibration curve, with different data transformations being tested. A polynomial equation was fitted to the data, taking into account a set of constraints to incorporate microbiological knowledge in the black box model. Hence, illogical interpolation results and overfitting of the data could be avoided. CONCLUSIONS: Different stress factors are affecting the relationship between the OD and the cell count of L. monocytogenes by lowering the cell viability. These effects could be modelled using a constrained polynomial model. SIGNIFICANCE AND IMPACT OF THE STUDY: The observed phenomena are important when calculating growth parameters, like growth rate and lag phase, based on OD data.

Calibration↗
PubMed2005

Protective influence of several packaging materials on light oxidation of milk.

Light-induced degradation reactions in milk create a serious problem for the dairy industry because of the development of off-flavors, the decrease in nutritional quality, and the severity and speed by which these phenomena develop. Packaging materials are essential to avoid this particular deterioration of milk. Therefore, efforts are being made to design protective polyethylene terephthalate (PET) packages. In the present study, a number of PET bottles were compared for their ability to avoid photo-oxidation in UHT semi-skimmed milk. The milk was packed in 3 types of PET bottles: one transparent bottle provided with an active oxygen-binding inner layer, one bottle with perfect light barrier, and one transparent bottle provided with a UV-absorbing additive. During 2 storage experiments, running parallel to each other for 2 mo, chemical milk quality parameters such as fat oxidation, vitamin and protein degradation, oxygen consumption, and color change were monitored. A trained taste panel compared the sensory quality of the illuminated milk stored in these bottles, with milk perfectly protected against light and oxygen. In the first study, milk was continuously illuminated at room temperature. A comparison was made for milk under storage conditions that simulated those expected during display in retail and supermarkets. The results of the 2 shelf-life studies showed that an adequate light barrier was apparently sufficient to avoid the light-induced oxidation of milk during extended storage. Oxygen barriers, on the other hand, did not provide a significant protection, nor did bottles with UV filter. If wavelengths detrimental to riboflavin were not completely excluded by the packaging material, incoming light could still give rise to photo degradation of milk. Accordingly, riboflavin and vitamin A were gradually degraded, milk fat was photo-oxidized, oxygen dissolved in the milk was consumed, and the sensorial quality decreased significantly.

Animals↗
PubMed2004

Obtaining single cells: analysis and evaluation of an experimental protocol by means of a simulation model.

The research presented in this paper analyses a newly developed experimental protocol for isolating single cells by constructing a simulation model of the process. The protocol involves sequential 50% dilutions of a cell suspension in a microtiter plate, so that eventually, wells are obtained containing exactly one cell. The aim of this modelling study is (i) to gain insight in the governing mechanisms of the dilution process, (ii) to confirm experimental findings and (iii) to enable the prediction of an average outcome for future experiments. The model construction process is presented chronologically. The initial basic model simulates the experiment as a sequence of binomial processes, using Monte Carlo techniques. Statistical analysis of the results shows that aggregational factors need to be taken into account in the form of a lognormal distribution. Several issues involved in this adaptation are discussed. To fully account for cell aggregation in the dilution process, a cell clumping algorithm is built into the simulation model. Simulation data from the resulting model show similar statistical characteristics as the experimental data and yield reliable prediction intervals for the available experimental data. The simulation model is a useful tool to support experimental findings and predict the outcome of future experiments. Even more importantly, this study emphasises the importance of careful statistical analysis in single cell research. The impact of stochastic effects is considerably amplified at the low cell concentrations involved and needs to be taken into account in any modelling effort.

Bacteria↗
PubMed2004

Modelling the individual cell lag phase: effect of temperature and pH on the individual cell lag distribution of Listeria monocytogenes.

The individual-based approach of the lag phase is gaining interest, especially for pathogens that initially contaminate food products in low amounts. In this paper, the effect of temperature (30, 10, 7, 4 and 2 degrees C) and pH (7.4, 6.1, 5.5, 5.0, 4.7 and 4.4) on the individual cell lag phase of Listeria monocytogenes was examined in a factorial design, using OD measurements. Individual lag phases of about 100 individual cells per condition were examined and calculated using a linear extrapolation method. Generation times were calculated out of the slope. The obtained data were analyzed at three different levels: in a first approach, the mean values were calculated for each set of environmental conditions and compared to predictions made by the USDA's Pathogen Modeling Program (PMP) for analogous growth conditions. The PMP predictions of the generation times were in the same order of magnitude as the obtained data, although a persistent underestimation could be observed. The observed individual cell lag data differed from lag phase predictions by PMP. Possible reasons for this discrepancy are discussed. Secondly, histograms of individual lag phase measurements were constructed for the different temperature-pH combinations. In this way, the influence of both factors on the variability of individual lag phases could be estimated. At low stress levels, most individual cells showed a short lag phase resulting in a compression of the histograms at the zero-lag level, while, at high stress levels, the histograms shifted to longer lag phases with a significant increase in variability. Thirdly, 37 different distribution types were fitted to the datasets to reveal the distributions that fitted best the obtained data. The gamma distribution was preferred at moderate stress levels, while the Weibull distribution was chosen for harsher growth conditions.

Colony Count, Microbial↗
PubMed2004

Evaluation of meat born lactic acid bacteria as protective cultures for the biopreservation of cooked meat products.

In this study, 91 strains, originating from meat products, were subjected to a step-by-step screening and characterisation to search for potential protective cultures to be used in the cooked cured meat industry. Strains were first tested on their homofermentative and psychrotrophic character and salt tolerance. Secondly, the antibacterial capacities towards Listeria monocytogenes, Leuconostoc mesenteroides, Leuconostoc carnosum and Brochotrix thermosphacta were determined in an agar spot test. In total, 38% of the tested strains were inhibitory towards all indicator strains. However, 91%, 88% and 74% of the strains could inhibit, respectively, L. monocytogenes, B. thermosphacta and Leuc. mesenteroides. Finally, 12 strains, with the highest antibacterial capacities, were evaluated on their competitive nature by comparing their growth rate, acidifying character and lactic acid production at 7 degrees C under anaerobic conditions in a liquid broth. All 12 strains, except for a bacteriocin producing Lactobacillus plantarum strain and the lactocin S producing Lactobacillus sakei 148, combined a fast growth rate with a deep and rapid acidification caused by the production of high levels of lactic acid. The 12 selected strains were then further investigated for their growth capacity on a model cooked ham product to establish whether the presence of these cultures on the ham did not negatively influence the sensory properties of the ham. All strains grew in 6 days at 7 degrees C from a level of 10(5)-10(6) to 10(7)-10(8) cfu/g and again the bacteriocin producing L. plantarum strain was the slowest growing strain. As the glucose level of the model cooked ham product was low (0.09+/-0.03%), growth of the putative protective cultures resulted in glucose depletion and a limited lactic acid production and accompanying pH decrease. Cooked ham inoculated with isolates 13E, 10A, 14A (all three identified as L. sakei subsp. carnosus by SDS-PAGE) and with strains L. sakei 148 (LS5) and L. sakei subsp. carnosus SAGA 777 (LS8) were not rejected by the sensory panel at the 34th day of the vacuum packaged storage at 7 degrees C. Therefore, these strains could have potential for the use as protective culture in cooked meat products.

Animals↗
PubMed2004

Development of a novel approach for secondary modelling in predictive microbiology: incorporation of microbiological knowledge in black box polynomial modelling.

This research deals with the development of a novel secondary modelling procedure within the framework of predictive microbiology. The procedure consists of three steps: (i) careful formulation of the available microbiological information, both from literature and from the experimental case study at hand, (ii) translation of these requirements in mathematical terms under the form of partial derivatives throughout the complete interpolation region of the experimental design, and (iii) determination of parameter values with suitable optimisation techniques for a flexible black box modelling approach, e.g., a polynomial model or an artificial neural network model. As a vehicle for this procedure, the description of the maximum specific growth rate of Lactobacillus sakei in modified BHI-broth as influenced by suboptimal temperature, water activity, sodium lactate and dissolved carbon dioxide concentration is under study. The procedure results in a constrained polynomial model with excellent descriptive and interpolating features in comparison with an extended Ratkowsky-type model and classical polynomial model, by combining specific properties of both model types. The developed procedure is illustrated on the description of the lag phase as well. It is stressed how the confrontation with experimental data is very important to appreciate the descriptive and interpolating capacities of new or existing models, which is nowadays not always carefully performed. Alternatively, the first two steps of the novel procedure can be used as a tool to demonstrate clearly (possible) interpolative shortcomings of an existing model with straightforward spreadsheet calculations.

Carbon Dioxide↗
PubMed2004

Evaluation of a challenge testing protocol to assess the stability of ready-to-eat cooked meat products against growth of Listeria monocytogenes.

Challenge testing of ready-to-eat (RTE) foods with Listeria monocytogenes is recommended to assess the potential for growth. The present study was undertaken to evaluate a protocol for challenge testing applied to RTE cooked meat products. In order to choose L. monocytogenes strains with a representative behaviour, initially, the variability of the response of multiple L. monocytogenes strains of human and food origin to different stress and growth conditions was established. The strains were not inhibited in their growth at moderate acid pH (5.25) and the four strains tested in particular showed a similar acid-adaptive response. Growth of the various strains under four different combined stress conditions indicated that no L. monocytogenes strain had consistently significant longer or shorter lag phase or higher or lower maximum specific growth rates. The effect of choice of strain and history (pre-incubation temperature 7 or 30 degrees C) on growth of L. monocytogenes under optimum conditions (Brain Heart Infusion, BHI) and modified BHI simulating conditions of cooked ham and paté was studied. In general, all four L. monocytogenes strains behaved similarly. In BHI, no difference in lag phase was observed for the cold-adapted and standard inoculum, whereas in BHI adjusted to ham and pâté conditions, a ca. 40-h reduction of the lag phase was noted for the cold-adapted inoculum. Subsequently, microbial challenge testing of L. monocytogenes in modified atmosphere packaged sliced cooked ham and paté was performed. A mixed inoculum of four L. monocytogenes strains and an inoculum level of ca. 1-10 cfu/g was used. On vacuum packed sliced cooked ham, the concentration of 100 cfu/g, the safety limit considered as low risk for causing listeriosis, was exceeded after 5 days whereas ca. 10(5) cfu/g were obtained after 14 days when also LAB spoilers reached unacceptable numbers (ca. 10(7) cfu/g) whether standard or cold-adapted inoculum was used. The concentration of sodium lactate determined the opportunities for growth of L. monocytogenes in pâté. If growth of L. monocytogenes in pâté was noticed, the threshold of 100 cfu/ml was crossed earlier for the cold-adapted inoculum compared to the standard inoculum.

Adaptation, Physiological↗
PubMed2004

Influence of polymer matrix and adsorption onto silica materials on the migration of alpha-tocopherol into 95% ethanol from active packaging.

In this study, the effect of polymer materials with different polarity, namely low density polyethylene (LDPE) and ethylene vinyl acetate (EVA), on the migration behaviour of alpha-tocopherol from active packaging was investigated. The antioxidant was also adsorbed onto silica materials, namely SBA-15 (Santa Barbara-15) and Syloblock, in order to protect the antioxidant during extrusion and to ensure a controlled and sufficient release during the shelf-life of the food product. Migration experiments were performed at 7.0 +/- 0.5 degrees C and 95% ethanol was used as fatty food simulant. All films contained a high concentration of alpha-tocopherol, approximately 2000 mg kg(-1), to obtain an active packaging. Polymer matrix had a small influence on the migration profile. The migration of 80% of total migrated amount of antioxidant was retarded for 2.4 days by using LDPE instead of EVA. When alpha-tocopherol was adsorbed onto both silica materials, the migration of 80% of total migrated amount of antioxidant was retarded for 3.4 days in comparison to pure alpha-tocopherol. No difference was seen between the migration profiles of alpha-tocopherol adsorbed onto both silica materials. In the case of pure alpha-tocopherol, 82% of the initial amount of alpha-tocopherol in the film migrated into the food simulant at a rather fast migration rate. In the case of adsorption on silica materials, a total migration was observed. These antioxidative films can have positive food applications.

Adsorption↗
PubMed2004

Effect of chemicals on the microbial evolution in foods.

In contrast with most chemical hazardous compounds, the concentration of food pathogens changes during processing, storage, and meal preparation, making it difficult to estimate the number of microorganisms or the concentration of their toxins at the moment of ingestion by the consumer. These changes are attributed to microbial proliferation, survival, and/or inactivation and must be considered when exposure to a microbial hazard is assessed. The number of microorganisms can also change as a result of physical removal, mixing of food ingredients, partitioning of a food product, or cross-contamination (M. J. Nauta. 2002. Int. J. Food Microbiol. 73:297-304). Predictive microbiology, i.e., relating these microbial evolutionary patterns to environmental conditions, can therefore be considered a useful tool for microbial risk assessment, especially in the exposure assessment step. During the early development of the field (late 1980s and early 1990s), almost all research was focused on the modeling of microbial growth over time and the influence of temperature on this growth. Later, modeling of the influence of other intrinsic and extrinsic parameters garnered attention. Recently, more attention has been given to modeling of the effects of chemicals on microbial inactivation and survival. This article is an overview of different applied strategies for modeling the effect of chemical compounds on microbial populations. Various approaches for modeling chemical growth inhibition, the growth-no growth interface, and microbial inactivation by chemicals are reviewed.

Bacteria↗
PubMed2003

Relation between microbiological quality, metabolite production and sensory quality of equilibrium modified atmosphere packaged fresh-cut produce.

The quality of four types of fresh-cut produce, packaged in consumer-sized packages under an equilibrium modified atmosphere and stored at 7 degrees C, was assessed by establishing the relation between the microbial outgrowth and the corresponding production of nonvolatile compounds and related sensory disorders. In vitro experiments, performed on a lettuce-juice-agar, demonstrated the production of nonvolatile compounds by spoilage causing lactic acid bacteria and Enterobacteriaceae. Pseudomonas fluorescens and yeasts, however, were not able to produce detectable amounts of nonvolatile metabolites. The type of spoilage and quality deterioration in vivo depended on the type of vegetable. Mixed lettuce and chicory endives, leafy tissues, containing naturally low concentrations of sugars, showed a spoilage dominated by Gram-negative microorganisms, which are not producing nonvolatile compounds. Sensory problems were associated with visual properties and the metabolic activity of the plant tissue. Mixed bell peppers and grated celeriac, on the other hand, demonstrated a fast and intense growth of spoilage microorganisms, dominated by lactic acid bacteria and yeasts. This proliferation resulted in detectable levels of organic acids and the rejection by the trained sensory panel was based on the negative perception of the organoleptical properties (off-flavour, odour and taste). The applied microbiological criteria corresponded well with detectable changes in sensory properties and measurable concentrations of nonvolatile compounds, surely in the cases where lactic acid bacteria and yeasts were provoking spoilage. Consequently, the freshness of minimally processed vegetables, sensitive for outgrowth of lactic acid bacteria and yeasts (e.g., carrots, celeriac, bell peppers, mixtures with non-leafy vegetables) can be evaluated via analysis of the produced nonvolatile compounds.

Bacteria↗
PubMed2003

Modelling the individual cell lag phase. Isolating single cells: protocol development.

AIMS: To develop a protocol to isolate single cells in wells of a microtitre plate, having a high certainty of individual cells, combined with a sufficient yield. METHODS AND RESULTS: Single cells were obtained using 1/2 dilution series in microtitre plates. Seventy-two Lactococcus lactis dilution series were checked by plate counting. When the last five columns of the plates were observed, the chance of having one single cell was 80%, while the yield was 75 wells containing cells. A simulation model confirmed these results. This method was compared with the commonly applied method. CONCLUSIONS: This method makes it possible to combine a higher chance of having one cell in a microtitre well with a slightly higher yield. SIGNIFICANCE AND IMPACT OF THE STUDY: A tool is developed to isolate single cells to provide a suitable base for investigating and modelling the individual cell lag phase.

Cell Division↗
PubMed2002

Predictive modelling for packaging design: equilibrium modified atmosphere packages of fresh-cut vegetables subjected to a simulated distribution chain.

The impact of temperature fluctuations in a simulated cold distribution chain, typical of commercial practice, was investigated on both the microbial and sensorial quality of equilibrium modified atmosphere (EMA) packaged minimally processed vegetables. The internal O2 concentration of the designed packages could be predicted for the different steps of the simulated distribution chain by applying an integrated mathematical system. The internal atmosphere in the packages remained in its aerobic range during storage in the chain due to the application of high permeable packaging films for O2 and CO2. Spoilage microorganisms were proliferating fast on minimally processed bell peppers and lettuce. Yeasts showed to be the shelf-life limiting group. Visual properties limited the sensorial shelf-life. Listeria monocytogenes was able to multiply on cucumber slices, survived on minimally processed lettuce and decreased in number on bell peppers due to the combination of low pH and refrigeration. Aeromonas caviae was multiplying on both cucumber slices and mixed lettuce, but was as well inhibited by the low pH of bell peppers. Storage temperature control was found to be of paramount importance for the microbial (spoilage and safety) and sensorial quality evaluation of EMA-packaged minimally processed vegetables.

Bacteria↗
PubMed2002

Effectiveness of some recent antimicrobial packaging concepts.

A new type of active packaging is the combination of food-packaging materials with antimicrobial substances to control microbial surface contamination of foods. For both migrating and non-migrating antimicrobial materials, intensive contact between the food product and packaging material is required and therefore potential food applications include especially vacuum or skin-packaged products, e.g. vacuum-packaged meat, fish, poultry or cheese. Several antimicrobial compounds have been combined with different types of carriers (plastic and rubber articles, paper-based materials, textile fibrils and food-packaging materials). Until now, however, few antimicrobial concepts have found applications as a food-packaging material. Antimicrobial packaging materials cannot legally be used in the EU at the moment. The potential use would require amendments of several different legal texts involving areas such as food additives, food packaging, hygiene, etc. The main objective of this paper is to provide a state of the art about the different types of antimicrobial concepts, their experimental development and commercialization, and to present a case study summarizing the results of investigations on the feasibility of a low-density polyethylene (LDPE)-film containing triclosan to inhibit microbial growth on food surfaces and consequently prolong shelf-life or improve microbial food safety. In contrast with the strong antimicrobial effect in in-vitro simulated vacuum-packaged conditions against the psychrotrophic food pathogen L. monocytogenes, the 1000 mg kg(-1) containing triclosan film did not effectively reduce spoilage bacteria and growth of L. monocytogenes on refrigerated vacuum-packaged chicken breasts stored at 7 degrees C.

Animals↗
PubMed2001

Effect of high oxygen modified atmosphere packaging on microbial growth and sensorial qualities of fresh-cut produce.

The application of High Oxygen Atmospheres (HOA) (i.e. > 70% O2) for packaging ready-to-eat vegetables was evaluated as an alternative technique for low O2 Equilibrium Modified Atmosphere (EMA) packaging (3% O2-5% CO2-balance N2) for respiring products. Comparative experiments between both techniques were performed in-vitro and in-vivo. Typical spoilage causing microorganisms (Pseudomonas fluorescens, Candida lambica), the moulds Botrytis cinerea, Aspergillus flavus and the opportunistic psychrotrophic human pathogenic microorganism associated with refrigerated minimally processed vegetables. Aeromonas caviae (HG4), showed a retarded growth during the conducted in-vitro studies at 4 degrees C in 70%, 80% and 95% O2 as examples of HOA compared to the in-vitro experiments in 5% O2 (as example of EMA packaging) and the effect was more pronounced in 95% O2. The effect of the high O2-concentrations on the human pathogen Listeria monocytogenes resulted in an extended lag phase (95% O2). The plant pathogen Erwinia carotovora was increasingly stimulated by increasing high O2-concentrations. During a storage experiment of three types of ready-to-eat vegetables (mushroom slices, grated celeriac and shredded chicory endive), which are sensitive to enzymatic browning and microbial spoilage, the effect of EMA and HOA (95% O2-5% N2) on their quality and shelf life was compared. High O2 atmospheres were found to be particularly effective in inhibiting enzymatic browning of the tested vegetables. Also, the microbial quality was better as a reduction in yeast growth was observed. The HOA can be applied as an alternative for low O2 modified atmospheres for some specific types of ready-to-eat vegetables, sensitive to enzymatic browning and spoilage by yeasts.

Bacteria↗
PubMed2001

Influence of acetate and CO2 on the TMAO-reduction reaction by Shewanella baltica.

In this work, the TMAO-reduction by Shewanella baltica, one of the representative spoilage organisms in modified atmosphere packaged marine fish fillets, and the effect of acetate and CO2 on this reduction were studied in vitro. The growth of S. baltica and the corresponding evolution of some compounds (acetate, lactate, pyruvate, glucose and trimethylamine (TMA)) were followed during storage at 4 degrees C in two types of broths. The first medium was a defined medium (pH = 6.8) to which lactate or pyruvate was added as hydrogen donor. Pyruvate showed to be more efficient as H-donor for S. baltica than lactate, as growth was much faster when equimolar amounts of pyruvate instead of lactate were present. Although the growth of S. baltica, when pyruvate is used as H-donor and no acetate is added, was not much inhibited by the CO2-atmosphere, CO2 had a pronounced effect on the studied reactions as it partly inhibited the reduction of pyruvate to acetate. The effect of acetate on this reaction was, on the other hand, not significant. To simulate the reactions occurring in situ, a buffered fish extract (pH = 6.8) was used. In spite of the neutral pH, the growth of S. baltica in this medium was highly inhibited by relatively small concentrations of acetate (< 0.3%). When 0.1% of acetate was added to the fish extract, less acetate was formed and lactate was more slowly consumed in comparison to the experiments without the addition of acetate. The consumption of lactate and the production of acetate were almost completely inhibited when the fish extract contained 0.25% of acetate. Apparently, the addition of acetate inhibited the use of lactate as H-donor. After extended storage times (17 days at 4 degrees C) TMA production started. Most probably, alternative H-donors were used by S. baltica, from which the pathway seems to be less energy efficient. This can be deduced from the exceptional growth inhibition of S. baltica by small amounts of acetate. However, when practical storage times for fish (e.g. 6 days at 4 degrees C after packaging) are considered, growth and TMAO-reduction by S. baltica was completely inhibited during this period by 0.25% of acetate.

Acetates↗