Biomedical subjects

Dirk W Grijpma

Publications and source records attributed to Dirk W Grijpma.

At least 19 recordsLinked to original sources

PubMed2006

Release of anti-restenosis drugs from poly(ethylene oxide)-poly(DL-lactic-co-glycolic acid) nanoparticles.

Dexamethasone- or rapamycin-loaded nanoparticles based on poly(ethylene oxide) and poly(dl-lactic-co-glycolic acid) block copolymers (PEO-PLGA) were prepared without additional stabilizer using the salting-out method. A fast release of drug in PBS (pH 7.4) at 37 degrees C resulting in 100% release within 5 h was observed for both drugs. The rate of drug release was substantially reduced by treating the particles with gelatin or albumin after drug loading, resulting in a linear drug release in time. It was shown that the rate of drug release is related to the amount of protein associated with the nanoparticles. After gelatin treatment of drug-loaded nanoparticles, sustained release of dexamethasone for 17 days and of rapamycin for 50 days could be achieved.

Coronary Restenosis↗

PubMed2006

Thermo-sensitive transition of monomethoxy poly(ethylene glycol)-block-poly(trimethylene carbonate) films to micellar-like nanoparticles.

Monomethoxy poly(ethylene glycol)-block-poly(trimethylene carbonate) (mPEG(3)-PTMC(11), M(n) of mPEG=3.1 x 10(3) and M(n) of PTMC=10.8 x 10(3)g/mol) was synthesized by ring-opening polymerization of TMC using mPEG(3) as an initiator and stannous octoate as a catalyst. The block copolymer has a broad melting range with a peak at 49.5 degrees C and a heat of fusion of 47.6J/g. The heat of fusion normalized to the mPEG content is higher than that of the mPEG(3) polymer, suggesting that PTMC segments are also semi-crystalline. The mPEG(3)-PTMC(11) films were stable in water at room temperature, whereas at 37 degrees C the film specimens disintegrated and the amphiphilic block copolymer self-assembled into micellar-like nanoparticles with average sizes up to 210nm. The critical association concentration (CAC) of the formed micellar-like particles is 1.35 x 10(-3)mg/ml. The average size and polydispersity index of the formed mPEG(3)-PTMC(11) nanoparticles depend on temperature and storage time: the values decrease with increases in temperature and in storage time. By co-dissolving dexamethasone with mPEG(3)-PTMC(11) during the film preparation, micellar-like nanoparticles loaded with dexamethasone can be obtained after the film to micellar-like nanoparticles transition. A high loading efficiency of 93.3 wt.% was achieved. The sustained release of the drug was complete in 20d.

Delayed-Action Preparations↗

PubMed2006

Poly(trimethylene carbonate) and monomethoxy poly(ethylene glycol)-block-poly(trimethylene carbonate) nanoparticles for the controlled release of dexamethasone.

In this study, single emulsion and salting out methods were employed to prepare poly(trimethylene carbonate) (PTMC) and monomethoxy poly(ethylene glycol)-block-poly(trimethylene carbonate) (mPEG-PTMC) nanoparticles. Well-defined nanoparticles of a PTMC homopolymer were prepared using poly(vinyl alcohol) (PVA) as a stabilizer. The average size of the nanoparticles can be adjusted by varying the stirring speed and polymer concentration. These particles can be readily freeze-dried and redispersed, with little influence on the average particle size and size distribution. Nanoparticles based on amphiphilic mPEG-PTMC can be prepared without an additional stabilizer. In this case, the size of the obtained nanoparticles did not vary much and ranged between 95 and 120 nm. These nanoparticles could be freeze-dried and redispersed as well. Using the salting out method, dexamethasone was loaded into PTMC and mPEG-PTMC nanoparticles at a highest efficiency of respectively 54% and 88%. With the single emulsion method, the loading efficiencies were, respectively, 91% and 72%. These drug-loaded particles were stable in time for at least 20 weeks. It was found that the release of dexamethasone from these nanoparticles was diffusion-controlled and could be sustained for 14 to 60 days. Depending on the nature of the polymer employed and the preparation method, dexamethasone diffusion coefficients varied between 4.8 x 10(-18) and 22.6 x 10(-18) cm(2)/s.

Anti-Inflammatory Agents↗

PubMed2006

Porous hybrid structures based on P(DLLA-co-TMC) and collagen for tissue engineering of small-diameter blood vessels.

Poly (D,L-lactide)-7co-(1,3-trimethylene carbonate) [P(DLLA-co-TMC)] (83 mol % DLLA) was used to produce matrices suitable for tissue engineering of small-diameter blood vessels. The copolymer was processed into tubular structures with a porosity of approximately 98% by melt spinning and fiber winding, thus obviating the need of organic solvents that may compromise subsequent cell culture. Unexpectedly, incubation in culture medium at 37 degrees C resulted in disconnection of the contact points between the polymer fibers. To improve the structural stability of these P(DLLA-co-TMC) scaffolds, a collagen microsponge was formed inside the pores of the synthetic matrix by dip coating and freeze drying. Hybrid structures with a porosity of 97% and an average pore size of 102 mum were obtained. Structural stability was preserved during incubation in culture medium at 37 degrees C. Smooth-muscle cells (SMCs) were seeded in these hybrid scaffolds and cultured under pulsatile flow conditions in a bioreactor (120 beats/min, 80-120 mmHg). After 7 days of culture in a dynamic environment viable SMCs were homogeneously distributed throughout the constructs, which were five times stronger and stiffer than noncultured scaffolds. Values for yield stress (2.8 +/- 0.6 MPa), stiffness (1.6 +/- 0.4 MPa), and yield strain (120% +/- 20%) were comparable to those of the human artery mesenterica.

Blood Vessel Prosthesis↗

PubMed2005

The in vivo and in vitro degradation behavior of poly(trimethylene carbonate).

The in vivo and in vitro degradation behavior of poly(trimethylene carbonate) (PTMC) polymers with number average molecular weights of 69 x 10(3), 89 x 10(3), 291 x 10(3) and 457 x 10(3)g/mol (respectively abbreviated as PTMC(69), PTMC(89), PTMC(291) and PTMC(457)) was investigated in detail. PTMC rods (3mm in diameter and 4mm in length) implanted in the femur and tibia of rabbits degraded by surface erosion. The mass loss of high molecular weight PTMC(457) specimens was 60wt% in 8 wks, whereas the mass loss of the lower molecular weight PTMC(89) specimens in the same period was 3 times lower. PTMC discs of different molecular weights immersed in lipase solutions (lipase from Thermomyces lanuginosus) degraded by surface erosion as well. The mass and thickness of high molecular weight PTMC(291) discs decreased linearly in time with an erosion rate of 6.7 microm/d. The erosion rate of the lower molecular weight PTMC(69) specimens was only 1.4mum/d. It is suggested that the more hydrophilic surface of the PTMC(69) specimens prevents the enzyme from acquiring a (hyper)active conformation. When PTMC discs were immersed in media varying in pH from 1 to 13, the non-enzymatic hydrolysis was extremely slow for both the high and low molecular weight samples. It can be concluded that enzymatic degradation plays an important role in the surface erosion of PTMC in vivo.

Absorbable Implants↗

PubMed2005

Preparation of biodegradable networks by photo-crosslinking lactide, epsilon-caprolactone and trimethylene carbonate-based oligomers functionalized with fumaric acid monoethyl ester.

Biodegradable polymer networks were prepared from fumaric acid derivatives of oligomeric esters. Photo-crosslinkable macromers were prepared by reacting star-shaped hydroxyl-group terminated lactide, epsilon-caprolactone and trimethylene carbonate based oligomers and fumaric acid monoethyl ester in the presence of N,N-dicyclohexylcarbodiimide and 4-dimethylamino pyridine at room temperature. The functionalization method is facile and suited for many hydroxyl-terminated oligomers. The reactivity of the fumarate end groups is such that, upon crosslinking by UV radical polymerization, networks with high gel contents (up to 96%) can be obtained without the addition of reactive diluents. The physical properties of the networks can be tuned by adjusting the composition, architecture and molecular weight of the oligomeric precursors. Such networks, built up of non-toxic compounds and designed to release benign degradation products, may find wide application in tissue engineering and other areas of biomedical research.

4-Aminopyridine↗

PubMed2004

In vitro degradation of nanoparticles prepared from polymers based on DL-lactide, glycolide and poly(ethylene oxide).

Nanoparticles of poly(DL-lactic acid) (PDLLA), poly(DL-lactic-co-glycolic acid) (PLGA) and poly(ethylene oxide)-PLGA diblock copolymer (PEO-PLGA) were prepared by the salting-out method. The in vitro degradation of PDLLA, PLGA and PEO-PLGA nanoparticles in PBS (pH 7.4) at 37 degrees C was studied. The particle size, molecular weight of the polymers and the amount of lactic and glycolic acids formed were followed in time. PDLLA nanoparticles gradually degraded over a period of 2 years and retain their size during that period. A faster degradation was observed for PLGA nanoparticles, which was nearly complete after 10 weeks. PLGA nanoparticles retained their size during that period. In PEO-PLGA nanoparticles, the ester bond connecting the PEO and the PLGA segments was preferentially cleaved, which led to a relatively fast decrease in molecular weight and to (partial) aggregation, as multimodal size distributions were observed. PEO-PLGA nanoparticles were almost completely degraded within 8 weeks.

Algorithms↗

PubMed2004

Liquid chromatographic-mass spectrometric studies on the in vitro degradation of a poly(ether ester) block copolymer.

A detailed study on the in vitro degradation of a poly(ethylene glycol) and poly(butylene terephthalate) (PEOT/PBT) segmented block copolymer was carried out using liquid chromatography/electrospray-mass spectrometry. Accelerated hydrolysis of PEOT/PBT was achieved by placing the material for 14 days in a refluxing phosphate buffered saline (pH 7.4) solution. All major degradation products and several side-products were identified using both the positive and the negative ion mode. The data indicate that degradation does not only occur in the "soft", but also in the "hard" segments of the polymer. Liquid chromatographic separation is required to distinguish between degradation products with different sequences but identical molecular mass. The addition of ammonium and sodium ions provided important complementary information on the number of monomer units present in the degradation products.

Chromatography, Liquid↗

PubMed2004

Creep-resistant porous structures based on stereo-complex forming triblock copolymers of 1,3-trimethylene carbonate and lactides.

Stereo-complexes (poly(ST-TMC-ST)) of enantiomeric triblock copolymers based on 1,3-trimethylene carbonate (TMC) and L- or D-lactide (poly(LLA-TMC-LLA) and poly(DLA-TMC-DLA)) were prepared. Films of poly(ST-TMC-ST) could be prepared by solvent casting mixtures of equal amounts of poly(LLA-TMC-LLA) and poly(DLA-TMC-DLA) solutions and by compression moulding co-precipitates. Although compression moulding was performed at 191 degrees C, thermal degradation was not apparent and materials with good tensile properties could be obtained. For compression-moulded poly(ST-TMC-ST) specimens containing approximately 16 mol % lactide, the values for E-modulus, yield stress and elongation at break were respectively 17, 1.7 MPa and 90%. Also a very low long-term creep rate of 2.2 x 10(-7)s(-1) was determined when specimens were loaded to 20% of the yield stress. When compared with compression-moulded poly(TMC), poly(ST-TMC-ST) specimens deform at a rate that is one to two orders of magnitude lower. Furthermore, poly(ST-TMC-ST) specimens showed complete dimensional recovery within 24 h after loading to 20% and 40% of the yield stress for 40 and 5.5 h, respectively. Highly porous poly(TMC) and poly(ST-TMC-ST) structures with interconnected pores were prepared by a method combining co-precipitation, compression moulding and salt leaching. After prolonged compressive deformation, solid and porous poly(ST-TMC-ST) discs showed significantly better recovery behaviour than poly(TMC) discs.

Biocompatible Materials↗

PubMed2003

Adhesion and growth of human Schwann cells on trimethylene carbonate (co)polymers.

Seeding of artificial nerve grafts with Schwann cells is a promising strategy for bridging large nerve defects. The aim of the present study was to evaluate the adhesion and growth of human Schwann cells (HSCs) on 1,3-trimethylene carbonate (TMC) and epsilon-caprolactone copolymers, with the final goal of using these materials in the development of an artificial nerve graft. The adhesion, proliferation, and morphology of HSCs on copolymers containing 10 and 82 mol % of TMC and on the parent homopolymers were investigated. HSCs adhered faster and in greater numbers on the copolymer with 82 mol % of TMC and on the TMC homopolymer compared with the other (co)polymers. On all polymer films, cell adhesion was lower than on gelatin (positive control). Despite differences in cell adhesion, cells displayed exponential growth on all tested surfaces, with similar growth rates. Cell numbers doubled approximately every 3 days on all substrates. When the polymer films were coated with fibronectin, no significant differences in cell adhesion and proliferation were observed between coated polymer surfaces and gelatin. The results indicate that all tested materials support the adhesion and proliferation of HSCs and can in principle be used for the preparation of flexible and slowly degrading nerve guides.

Cell Adhesion↗

PubMed2003

Preparation of interconnected highly porous polymeric structures by a replication and freeze-drying process.

Three-dimensional degradable porous polymeric structures with high porosities (93-98%) and well-interconnected pore networks have been prepared by freeze-drying polymer solutions in the presence of a leachable template followed by leaching of the template. Templates of the pore network were prepared by fusing sugar or salt particles to form a well-connected structure. The interstices of the template were then filled with a polymer solution (5-15% w/v) in 1,4-dioxane, followed by freeze-drying of the solvent. Subsequent leaching of the sugar template ensures the connectivity of the pore network. The scaffold architecture consists of relatively large interconnected pores modeled after the template and smaller pores resulting from the freeze-drying process. The total porosity of the resultant porous structures is determined by the interstitial space of the leachable template and by the polymer concentration in the freeze-drying solution. The freezing temperature also has an effect on the final morphology of the porous structures. Compared with freeze-drying and combination of freeze-drying /particulate leaching techniques, this method facilitates higher interconnectivity of the scaffolds. Porous structures have been prepared from several relevant polymers in the biomedical and tissue-engineering field: poly(D,L-lactide) (PDLLA), 1000PEOT70PBT30, a segmented poly(ether ester) based on polyethylene oxide and polybutylene terephthalate, and poly(epsilon-caprolactone) (PCL). The mechanical properties of the porous structures prepared by this technique depend on the nature of the polymer, porosity, and the freezing temperature. With porosities in the range of 95-97%, the compression moduli of scaffolds prepared from the different polymers could be varied between 13.0 and 301.5 kPa.

Biocompatible Materials↗

PubMed2003

The preparation of monodisperse biodegradable polyester nanoparticles with a controlled size.

In local drug delivery, nanoparticles based on biodegradable polymers can function as vehicles with controlled drug-release properties. To achieve a well-controlled drug-release profile, control over the particle size is of great importance. Therefore, biodegradable polyester nanoparticles were prepared by the salting-out method. Process variables were varied to study the effect on the particle size. The monodisperse particles obtained were between 100 and 400 nm in size and spherical in shape. It was found that the particle size could be adjusted by varying the preparation conditions upon which the polymer concentration had the most pronounced effect.

Chemistry, Pharmaceutical↗

PubMed2003

Biodegradable elastomeric scaffolds for soft tissue engineering.

Elastomeric copolymers of 1,3-trimethylene carbonate (TMC) and epsilon-caprolactone (CL) and copolymers of TMC and D,L-lactide (DLLA) have been evaluated as candidate materials for the preparation of biodegradable scaffolds for soft tissue engineering. TMC-DLLA copolymers are amorphous and degrade more rapidly in phosphate-buffered saline (PBS) of pH 7.4 at 37 degrees C than (semi-crystalline) TMC-CL copolymers. TMC-DLLA with 20 or 50 mol% TMC loose their tensile strength in less than 5 months and are totally resorbed in 11 months. In PBS, TMC-CL copolymers retain suitable mechanical properties for more than a year. Cell seeding studies show that rat cardiomyocytes and human Schwann cells attach and proliferate well on the TMC-based copolymers. TMC-DLLA copolymers with either 20 or 50 mol% of TMC are totally amorphous and very flexible, making them excellent polymers for the preparation of porous scaffolds for heart tissue engineering. Porous structures of TMC-DLLA copolymers were prepared by compression molding and particulate leaching techniques. TMC-CL (co)polymers were processed into porous two-ply tubes by means of salt leaching (inner layer) and fiber winding (outer layer) techniques. These grafts, seeded with Schwann cells, will be used as nerve guides for the bridging of large peripheral nerve defects.

Animals↗

PubMed2003

Porous PEOT/PBT scaffolds for bone tissue engineering: preparation, characterization, and in vitro bone marrow cell culturing.

The preparation, characterization, and in vitro bone marrow cell culturing on porous PEOT/PBT copolymer scaffolds are described. These scaffolds are meant for use in bone tissue engineering. Previous research has shown that PEOT/PBT copolymers showed in vivo degradation, calcification, and bone bonding. Despite this, several of these copolymers do not support bone marrow cell growth in vitro. Surface modification, such as gas-plasma treatment, is needed to improve the in vitro cell attachment. Porous structures were prepared using a freeze-drying and a salt-leaching technique, the latter one resulting in highly porous interconnected structures of large pore size. Gas-plasma treatment with CO(2) generated a surface throughout the entire structure that enabled bone marrow cells to attach. The amount of DNA was determined as a measure for the amount of cells present on the scaffolds. No significant effect of pore size on the amount of DNA present was seen for scaffolds with pore sizes between 250-1000 microm. Light microscopy data showed cells in the center of the scaffolds, more cells were observed in the scaffolds of 425-500 microm and 500-710 microm pore size compared to the ones with 250-425 microm and 710-1000 microm pores.

Alkaline Phosphatase↗

PubMed2003

Porous polymeric structures for tissue engineering prepared by a coagulation, compression moulding and salt leaching technique.

A technique for the preparation of porous polymeric structures involving coagulation, compression moulding and particulate leaching has been developed. The technique combines the advantages of thermal processing methods and particulate leaching. A high molecular weight polymer solution in an organic solvent containing dispersed water-soluble salt particles is precipitated into an excess of non-solvent. The polymer-salt composite is then processed by thermal processing methods into devices of varying shapes and sizes, which can subsequently be extracted to give the desired porous structures. The porosities of the scaffolds could be varied between 70% and 95% by adjusting the polymer to salt ratio and the pore size could be controlled independently by varying the leachable particle size. This versatility provides for the optimisation of scaffolds used in medicine and in tissue engineering. Compared with commonly used porosifying methods such as sintering, compression moulding combined with salt leaching, and freeze-drying, this process allows excellent control over pore size and porosity and yields scaffolds with a much more homogeneous pore morphology. We have prepared porous structures from several relevant polymers in the biomedical field: poly(D,L-lactide), poly(epsilon-caprolactone) and 1000PEOT70PBT30, a segmented poly(ether ester) based on polyethylene oxide and polybutylene terephthalate.

Absorbable Implants↗

PubMed2003

Positively charged biomaterials exert antimicrobial effects on gram-negative bacilli in rats.

Biomaterial-centered infection is a much-dreaded complication associated with the use of biomedical implants. Although positively charged biomaterial surfaces stimulate bacterial adhesion, it has been suggested that surface growth of adhering Gram-negative bacilli is inhibited on positively charged surfaces. In the present paper, we determined the infection rate of differently charged poly(methacrylates) in rats. To this end, 2 x 10(6)/cm(2) Escherichia coli O2K2 or 2 x 10(4)/cm(2) Pseudomonas aeruginosa AK1 were seeded on glass discs coated with three differently charged poly(methacrylates) coatings in a parallel plate flow chamber. Three rats received six subcutaneous discs (two discs of each charge variant) seeded with E. coli, while three other rats received discs seeded with P. aeruginosa. The numbers of viable bacteria on the surfaces were determined 48h after implantation. On 50% of all positively charged discs viable E. coli were absent, while the negatively charged discs were all colonized by E. coli. P. aeruginosa, however, were isolated from both positively and negatively charged discs. Probably, P. aeruginosa can circumvent the antimicrobial effect of the positive charge through the formation of extracellular polysaccharides.

Animals↗

PubMed2003

Physical properties of high molecular weight 1,3-trimethylene carbonate and D,L-lactide copolymers.

High molecular weight statistical copolymers of 1,3-trimethylene carbonate (TMC) and D,L-lactide (DLLA) were synthesized and characterized with the aim of assessing their potential in the development of degradable and flexible materials for application in the biomedical field. Under the applied polymerization conditions (130 degrees C, 3 days using stannous octoate as a catalyst) monomer conversion was high or almost complete, and high molecular weight polymers (M(n) above 170 000) were obtained. Significant improvement of the mechanical performance of these materials was observed in comparison to results previously reported for TMC and DLLA based copolymers of lower molecular weight. For the entire range of compositions the polymers are amorphous with a glass transition temperature ranging between -17 degrees C for poly(TMC) and 53 degrees C for poly(DLLA). The polymers vary from rubbers to stiff materials as the content of TMC decreases. All polymers are hydrophobic with very low equilibrium water absorption (<1.5 wt %). Thermal analyses and tensile tests were performed on polymer samples after water uptake. Due to a plasticizing effect of the water, the thermal properties, and consequently the mechanical performance, of the copolymers with higher content of DLLA were the most affected. After water absorption, the polymer mechanical behavior can change from glassy to rubbery, as observed for the copolymer with 80 mol % of DLLA. The obtained results suggest that these copolymers are promising candidates as biomaterials in the preparation of degradable medical devices and systems.

Journal Article↗

PubMed2002

Design of segmented poly(ether ester) materials and structures for the tissue engineering of bone.

In this study, PEOT/PBT segmented copolymers of different compositions have been evaluated as possible scaffold materials for the tissue engineering of bone. By changing the composition of PEOT/PBT copolymers, very different mechanical and swelling behaviors are observed. Tensile strengths vary from 8 to 23 MPa and elongations at break from 500 to 1300%. Water-uptake ranges from 4 up to as high as 210%. The in vitro degradation of PEOT/PBT copolymers occurs both by hydrolysis and oxidation. In both cases degradation is more rapid for copolymers with high PEO content. PEOT/PBT scaffolds with varying porosities and pore sizes have been prepared by molding and freeze-drying techniques in combination with particulate-leaching. The most hydrophilic PEOT/PBT copolymers did not sustain goat bone marrow cell adhesion and growth. However, surface modification by gas plasma treatment showed a very much improved polymer-cell interaction for all PEOT/PBT copolymer compositions. Their mechanical properties, degradability and ability to sustain bone marrow cell growth make PEOT/PBT copolymers excellent materials for bone tissue engineering.

Animals↗