Search PubMed⌕ Search

Biomedical subjects

D J Lee

Publications and source records attributed to D J Lee.

At least 19 recordsLinked to original sources

Oxygen diffusion in active layer of aerobic granule with step change in surrounding oxygen levels.

High biomass density and large size limit the transfer of dissolved oxygen (DO) in aerobic granules. In the literature, the oxygen diffusivity is often employed as an input parameter for modeling transport processes in aerobic granules. The interior of an aerobic granule was observed to be highly heterogeneous. In this work, the distributions of extracellular polymeric substances (EPS) and cells in the interior of phenol-fed and acetate-fed granules were built up using a five-fold staining scheme, combined with the use of a confocal laser scanning microscope (CLSM). The steady-state and transient DO with step changes in surrounding DO levels at various depths were measured in the granules using microelectrodes. Cells were probed in a surface layer of thickness 125-375 microm. A marked fall in DO was also noted over this surface layer. No aerobic oxidation could occur beneath the active layer, indicating the oxygen transfer limit. Fitting the steady-state and transient DO data over the active surface layer yielded apparent diffusivities of oxygen were (9.5+/-3.5)x10(-10)m(2)s(-1) for the phenol-fed granule and (3.5+/-1.0)x10(-10)m(2)s(-1) for the phenol-fed granule. These values were lower than those adopted in models in the literature.

Acetates↗

Nanoparticles in wastewater from a science-based industrial park - coagulation using polyaluminum chloride.

The Hsinchu Science-based Industrial Park (HSIP) is the hi-tech manufacturing hub of Taiwan. Wastewater from the HSIP contains numerous nano-sized silicate particles whose size distributions peak at 2 and 90 nm. A 3-5 mg l(-1) as Al dose of polyaluminum chloride (PACl) was used in the field to coagulate these particles, but the removal efficiency was low. Laboratory scale tests indicated that although PACl coagulation removed 52% of the turbidity and 48% of the chemical oxygen demand (COD) from water, its effect on nano-particle removal was minimal. About 58% of the soluble COD was associated with colloidal Si particles. A light scattering test and transmission electron microscopy (TEM) demonstrated that the nano-particles agglomerated in approximately linear aggregates of sizes 100-300 nm. Prolonged contact between residual PACl and the nano-particles generated large aggregates with sizes of up to 10 microm and a fractal dimension of 2.24-2.63. The results presented herein should be of interest in the processing of "high-tech" wastewater that contains nanosized silica particles.

Aluminum Hydroxide↗

Membrane biofouling by extracellular polymeric substances or soluble microbial products from membrane bioreactor sludge.

This study extracted the soluble microbial products and loosely bound and tightly bound extracellular polymeric substances (EPS) from suspended sludge from a membrane bioreactor, original and aerobically/anaerobically digested, and compared their fouling potentials on a microfiltration membrane. The resistance of cake layer accounts for 95-98% of the total filtration resistances when filtering the whole sludges, with anaerobically digested sludge presenting the highest resistance among the three tested sludges. The tightly bound EPS has the highest potential to foul the membrane; however, the loosely bound EPS contribute most of the filtration resistances of the whole sludges. The foulants corresponding to the irreversible fouling have chemical fingerprints similar to those from loosely bound EPS, which have a greater predilection to proteins and humic substances than to polysaccharides.

Aerobiosis↗

Distribution of extracellular polymeric substances in aerobic granules.

Extracellular matrix provides an architectural structure and mechanical stability for aerobic granules. Distributions of cells and extracellular polymeric substances (EPS), including proteins, alpha- and beta-D-glucopyranose polysaccharides, in acetate-fed granules and phenol-fed granules were probed using a novel quadruple staining scheme. In acetate-fed granules, protein and beta-D-glucopyranose polysaccharides formed the core, whereas, the cells and alpha-D-glucopyranose polysaccharides accumulated in the granule outer layers. Based on these experimental findings, this study indicated that different conclusions can be obtained regarding EPS distributions when granules were stained differently. The core of phenol-fed granules, conversely, was formed principally by proteins; whereas, the cells and alpha- and beta-D-glucopyranose polysaccharides were accumulated at an outer filamentous layer. Using a series of confocal laser scanning microscope (CLSM) images whose threshold values were determined via Otsu's scheme, the three-dimensional distributions of cells and EPS were produced using a polygonal surface model. Structural information extracted can be applied in further development of comprehensive granule models.

Aerobiosis↗

Diffusivity of oxygen in aerobic granules.

This work for the first time estimated apparent oxygen diffusivity (D(app)) of two types of aerobic granules, acetate-fed and phenol-fed, by probing the dissolved oxygen (DO) level at the granule center with a sudden change in the DO of the bulk liquid. With a high enough flow velocity across the granule to minimize the effects of external mass transfer resistance, the diffusivity coefficients of the two types of granules were estimated with reference to a one-dimensional diffusion model. The carbon source has a considerable effect on the granule diameter (d) and the oxygen diffusivity. The diffusivity coefficients were noted 1.24-2.28 x 10(-9) m2/s of 1.28-2.50 mm acetate-fed granules, and 2.50-7.65 x 10(-10) m2/s of 0.42-0.78 mm phenol-fed granules. Oxygen diffusivity declined with decreasing granule diameter, in particular, the diffusivity of acetate-fed granules is proportional to the size, whereas the diffusivity of phenol-fed granules is proportional to the square of granule diameter. The existence of large pores in granule, evidenced by FISH-CLSM imaging, was proposed to correspond to the noted size-dependent oxygen diffusivity. The phenol-fed granules exhibited a higher excellular polymer (ECP) content than the acetate-fed granules, hence yielding a lower oxygen diffusivity.

Acetates↗

Micromechanics of wastewater sludge floc: force-deformation relationship at cyclic freezing and thawing.

This study examined shape changes in two typical wastewater flocs subjected to cyclic freezing and thawing and the associated force exerted by the ice front. While freezing, the engulfing ice front gradually pulled the floc apart. Subsequent thawing only partially restored the floc's shape. By the Maxwell model, used to interpret gross shape deformations, both flocs were visco-elastic objects exhibiting time-varying rheological characteristics which were more viscous than elastic. Detailed observations of floc 1 deformation demonstrated a two-stage force-displacement relationship. Following 1 cycle of freezing and thawing, the interior structure of the floc deteriorated and the force required to elongating a unit length of floc decreased by 60%. The original floc 2 had a dense "core" and loose "tail"; the core was more resistant to deformation under normal stress than the loose tail. Although both flocs had similar shapes and sizes and were acquired from the same activated sludge stream at a wastewater treatment plant, their rheological behaviors differed substantially. A comprehensive theoretical model for freezing and thawing processes should incorporate these rheological characteristics as they corresponded to observed structural changes and reduction in bound water content in sludge following a cyclic treatment of freezing and thawing.

Journal Article↗

Nitrogen removal from recycled landfill leachate by ex situ nitrification and in situ denitrification.

A three-compartment system, comprising a landfill column with fresh municipal solid waste, a column with a well-decomposed refuse layer as methane producer, and a sequential batch reactor as ex situ nitrifying reactor, was employed to remove nitrogen from municipal solid waste leachate. Since food waste comprised a major portion of refuse collected in Shanghai, an intense hydrolysis reaction occurred and caused the rapid accumulation of ammonia nitrogen (NH(3)-N) and total organic carbon in the leachate. This paper discusses the role of the three mentioned units and the design and operation of the proposed system. With most NH(3)-N being converted to nitrite nitrogen (NO(2)(-)-N) or nitrate nitrogen (NO(3)(-)-N) by the nitrifying reactor, and with the well-decomposed refuse layer transforming most dissolved organic compounds to CO(2), carbonates and methane, it was found that the fresh refuse column could efficiently denitrify the hydrolyzed nitrogen to N(2) gas. The role of the three mentioned units and comments on the design and operation of the proposed system are also discussed.

Ammonia↗

Effect of alkali metal cation on the anaerobic hydrolysis and acidogenesis of vegetable waste.

Five batch testing scenarios were designed to evaluate the effects of alkali metal cations on anaerobic hydrolysis and acidogenesis. These scenarios were A (c=0 g l(-1)), B (cNa+=25 g l(-1)), C (cNa+=50 g l(-1)), D (cK+=25 g l(-1)), and E (cK+=50 g l(-1), pH 7.0). A solution pH of 7.0 or above favored protein hydrolysis, higher proteinase activity and higher ammonia production. However, such a pH suppressed carbohydrate hydrolysis, as indicated by low alpha-amylase activity. Cation interference at pH 5.0-6.0 seemed not to affect carbohydrate hydrolysis, as showed by the unimpaired alpha-amylase activity at 50 g l(-1) K+. Acidogenesis was more sensitive to alkali metal cations, so acid production and the drop in pH were lowest in a 25-50 g l(-1) Na+, acidic environment (pH 4.0-6.0). It was insensitive to cations when the pH was maintained at 7.0-8.0. When the pH was uncontrolled and decreased freely to acidic values, 25 g l(-1) of cation inhibited the action of the microbes, which rapidly acclimated, as presented by the slow transformation of soluble polymers to soluble metabolites. However, acidogenetic microbes could not easily recover from inhibition by 50 g l(-1) of cation. When the pH was maintained at over 7.0, the microbes were not inhibited by cation (50 g l(-1)) as indicated by the more active acidogenesis. The metabolic pathways to lactate, acetate and alcohols were not fully coupled.

Bacteria, Anaerobic↗

Sludge production and management processes: case study in China.

In 2010, the sewage sludge production rate will be 178,500 t dried solids (ds) for Beijing and 294,000 t-ds for Shanghai, respectively. Beijing adopts a centralized system to stabilize 78% of her sludge in three rural Stabilization Centres. Aerated composting technique will be used. Shanghai on the contrary decentralizes the management plan to treat the sludge on site. Diverse treatment trains, such as aerobic/anaerobic digestion, drying, incineration, and composting will be applied. Production rate, treatment plan, and the associated costs, energy consumption, carbon dioxide emission, and risk assessment for heavy metals and pathogens on human health were evaluated in this report for sludges yielded in Beijing and Shanghai, China.

Animals↗

Pulmonary tuberculosis in young Korean soldiers: incidence, drug resistance and treatment outcomes.

OBJECTIVE: To determine the incidence and treatment outcomes of pulmonary tuberculosis (PTB) in young soldiers of South Korea. DESIGN: From 2000 to 2004, all soldiers with a new diagnosis of tuberculosis (TB) were enrolled in the study, based on the official records of the Armed Forces Medical Command. The demographic and clinical data of the cases were evaluated retrospectively. RESULTS: A total of 3115 TB cases were reported during the study period, of whom 2071 (66.5%) were reported as PTB. The annual incidence rates of PTB were 96.4 per 100,000 population in 2000, 89.3 in 2001, 67.6 in 2002, 60.2 in 2003, and 63.1 in 2004. A total of 270 patients diagnosed and treated at the Armed Forces Capital Hospital were analysed. Of the Mycobacterium tuberculosis isolates, 87.4% were susceptible to all available anti-tuberculosis drugs; 253 (93.7%) patients eventually completed initial anti-tuberculosis treatment. Among the patients with smear-positive PTB, the cure rate was 89.3% (100/112). CONCLUSION: Our results demonstrate that the incidence of PTB in Korean soldiers, although still high, was declining steadily. With good case management, the overall success rate of initial treatment was approximately 90%.

Adult↗

Diffusion coefficient of Brownian particle in rough micro-channel.

This study examines the feasibility of using of the lattice Boltzmann method to determine how the surface roughness of a quadrate channel affects the diffusion coefficient of Brownian particle(s). The surface was represented by a regular array of spheres. Surface roughness reduced the diffusion coefficient of the Brownian particle(s) because of a change in the velocity autocorrelation function decay and in pressure. Additionally, the neighboring particles increased the diffusion coefficient of Brownian particle.

Journal Article↗

Rheological characteristics of the cationic polyelectrolyte flocculated wastewater sludge.

The rheological characteristics of the wastewater sludge were investigated by using a Haake Rheostress RS 75 rheometer. The stress-sweep experiments and the small-amplitude-oscillatory-shearing (SAOS) tests were conducted. The stress-sweep measurements demonstrate that addition of polymer coagulants to sludge samples could significantly influence the corresponding complex shear modulus G*. Furthermore, the SAOS tests indicate that the sludge samples treated with polymer coagulants will form more rigid structures. The original sludge samples mostly show typical viscoelastic liquid-like behavior. However, the solid-like behaviors were always observed in the samples treated with polymers.

Elasticity↗

Fragmentation of wastewater sludge floc by planar ice front.

Floc size has substantial impact on sludge dewaterability, which might be increased or reduced after freezing and thawing. It is commonly assumed that floc size would be increased by low-speed freezing, with a planar ice front rejecting most flocs ahead of it to form large aggregates. We demonstrate in this work that an advancing planar ice front can not only engulf an activated sludge floc of size 3030 mum, but also fragment it. During floc freezing, when the ice engulfed a thin layer of floc, the latter would be pulled apart vertically by the action of the former. This particular portion of floc was then axially elongated and fixed in the frozen layer, with accumulated force pushing upward. In the present test the floc's vertical length was increased by over 92% and its width decreased by 37% over freezing. The force measurement and floc morphology tracking revealed that the force gradient that pulled apart the floc was 0.0027 N/m. The floc under investigation was fragmented at the point where the normal stress acting on the interior network exceeded 8 Pa.

Journal Article↗

Thermodynamic parameters for adsorption equilibrium of heavy metals and dyes from wastewater with low-cost adsorbents.

This note revisits the literature evaluating the thermodynamic parameters of adsorption equilibrium uptakes of heavy metals and dyes from water and wastewater streams using low-cost adsorbents derived from agricultural waste, industrial wastes, inorganic particulates, or some natural products. We highlighted the possible flaws in some adsorption studies when their thermodynamic parameters were assessed, since compensation effects during enthalpy and entropy evaluation were possibly overlooked.

Adsorption↗

Energy demand in sludge dewatering.

This work investigates the energy required to dewater a suspension, i.e., activated sludge dewatered by centrifugation or consolidation. Total energy input to the suspension from the dewatering device, bond strength between adjacent water and solid surface, and intra-cake friction loss were evaluated for original and flocculated sludges. In centrifugal dewatering, most energy input during the initial stage was consumed by overcoming process irreversibility other than intra-cake friction, and, thereby, had a low energy efficiency. To increase centrifuge speed or to flocculate the sludge at optimal flocculant dosage would yield a high-energy input. In the consolidation test, most energy input at the initial stage was consumed in breaking down the bond strength until the moisture content reduced to less than the critical content. During subsequent dewatering stages, friction loss became the dominant source of energy loss. Dewatering sludge with high-energy efficiency is beneficial to optimally operate a dewatering process.

Centrifugation↗

Size-dependent anaerobic digestion rates of flocculated activated sludge: role of intrafloc mass transfer resistance.

The anaerobic digestion rate for flocculated sludge has been considered to be lower than that of original sludge, particularly in the later stages of digestion; attributed this relatively slower rate to the increased mass transfer resistance for reactants through the large flocs after flocculation. This study confirmed that methane production was retarded by flocculation. The structure of the floc was identified with fluorescence in situ hybridization (FISH) and a confocal laser scanning microscope (CLSM) technique. To verify the mass transfer resistance induced by flocculation, microsensors were applied to assess the response of oxygen concentration distribution inside the flocs that are subjected to sudden changes in ambient oxygen levels. Response time for the electrode at a floc's center was five times greater than the response time in original sludge flocs. Although the effective diffusivity of oxygen in the floc increased by 2.3 times after flocculation, the increased size of the flocculated floc was the major contributor to the total mass transfer resistance to oxygen.

Bacteria, Anaerobic↗

Steady-state humic-acid-containing blanket in upflow suspended bed.

We investigated the effects of turbidity and concentration of humic acid on the steady-state behavior of the blanket, which was coagulated using polyaluminum chloride (PACl) as coagulant. The three-dimensional solid-flux plot was constructed. Based on fixed PACl dosage, the iso-humic-acid solid-flux surfaces stacked that enveloped the feasible regime for the blanket bed. The steady-state point moved toward low solid flux and low solid fraction regime with decreasing initial raw water turbidity and/or increasing humic-acid concentration. Low water turbidity and high humic-acid concentration yielded a bulky blanket, with the former producing clean, and the latter turbid effluent. The presence of humic acid was thereby harmful to blanket strength, except for the case of low raw water turbidity. An optimal range of humic acid for blanket strength and clarification efficiency existed at 1 mg l(-1). Low level of humic acid is beneficial to blanket development with low-turbidity raw water.

Aluminum Chloride↗

Effects of aerobic exercise and obesity phenotype on abdominal fat reduction in response to weight loss.

OBJECTIVE: To test the effects on abdominal fat reduction of adding aerobic exercise training to a diet program and obesity phenotype in response to weight loss. DESIGN: A prospective clinical trial with a 14-week weight-loss intervention design. SETTING AND PARTICIPANTS: In total, 209 overweight and obese women were assigned to four subgroups depending on type of treatment and the subject's obesity phenotype: diet alone (DA) with intra-abdominal fat (IF) obesity (> or =mean IF area), diet plus exercise (DE) with IF obesity, DA with abdominal subcutaneous fat (ASF) obesity (<mean IF area) and DE with ASF obesity. Abdominal fat areas were evaluated by CT scans, with values adjusted for selected variables. RESULTS: Values were adjusted for age, menopausal status and change in body weight and total fat mass. The IF reductions were significantly (P<0.0001) greater in subjects with IF obesity phenotype (-45.1 cm2) compared to the ASF obesity phenotype (-22.2 cm2). The ASF reductions were significantly (P<0.001) greater for subjects with ASF obesity (-74.5 cm2) compared to IF obesity (-55.5 cm2). For IF obesity, the IF reduction was significantly (P<0.01) greater in the DE group (-49.3 cm2) than in the DA group (-37.8 cm2). CONCLUSION: These results suggest that for individuals with IF obesity, the efficacy on reducing IF of adding aerobic exercise training to a diet-alone weight-reduction program is more prominent (-49.3 cm2/-37.8 cm2=1.3 times) compared with DA. Moreover, abdominal fat reduction was found to be modified by obesity phenotype in response to weight loss.

Adult↗