Biomedical subjects

D H Pashley

Publications and source records attributed to D H Pashley.

At least 37 records · Page 2Linked to original sources

PubMed2004

Collagen degradation by host-derived enzymes during aging.

Incompletely infiltrated collagen fibrils in acid-etched dentin are susceptible to degradation. We hypothesize that degradation can occur in the absence of bacteria. Partially demineralized collagen matrices (DCMs) prepared from human dentin were stored in artificial saliva. Control specimens were stored in artificial saliva containing proteolytic enzyme inhibitors, or pure mineral oil. We retrieved them at 24 hrs, 90 and 250 days to examine the extent of degradation of DCM. In the 24-hour experimental and 90- and 250-day control specimens, we observed 5- to 6-microm-thick layers of DCM containing banded collagen fibrils. DCMs were almost completely destroyed in the 250-day experimental specimens, but not when incubated with enzyme inhibitors or mineral oil. Functional enzyme analysis of dentin powder revealed low levels of collagenolytic activity that was inhibited by protease inhibitors or 0.2% chlorhexidine. We hypothesize that collagen degradation occurred over time, via host-derived matrix metalloproteinases that are released slowly over time.

Acid Etching, Dental↗

PubMed2004

Interaction of glass-ionomer cements with moist dentin.

Glass-ionomer cements (GICs) are regarded as aqueous gels made up of polyalkenoic acid salts containing ion-leachable glass fillers. The consequence of water permeation across the GIC-dentin interface is unknown. This study used SEM, field-emission/environmental SEM (FE-ESEM), and TEM to examine the ultrastructure of GIC-bonded moist dentin. Dentin surfaces bonded with 6 auto-cured GICs were examined along the fractured GIC-dentin interfaces. Additional specimens fractured 3 mm away from the interfaces were used as controls. SEM revealed spherical bodies along GIC-dentin interfaces that resembled hollow eggshells. FE-SEM depicted similar bodies with additional solid cores. Energy-dispersive x-ray analysis and TEM showed that the spherical bodies consisted of a silicon-rich GIC phase that was absent from the air-voids in the controls. The GIC inclusions near dentin surfaces result from a continuation of the GI reaction, within air-voids of the original polyalkenoate matrix, that occurred upon water diffusion from moist dentin.

Adhesiveness↗

PubMed2004

Osmotic blistering in enamel bonded with one-step self-etch adhesives.

One-step self-etch adhesives behave as permeable membranes after polymerization, permitting water to move through the cured adhesives. We hypothesize that osmotic blistering occurs in bonded enamel when these adhesives are used without composite coupling. Tooth surfaces from extracted human premolars were bonded with 5 one-step self-etch adhesives. They were immersed in distilled water or 4.8 M CaCl(2), and examined by stereomicroscopy, field-emission/environmental SEM, and TEM. Water blisters were observed in bonded enamel but not in bonded dentin when specimens were immersed in water. They collapsed when water was subsequently replaced with CaCl(2). Blisters were absent from enamel in specimens that were immersed in CaCl(2) only. Water trees were identified from adhesive-enamel interfaces. Osmotic blistering in enamel is probably caused by the low water permeability of enamel. This creates an osmotic gradient between the bonded enamel and the external environment, causing water sorption into the interface.

Acid Etching, Dental↗

PubMed2004

Collagen degradation in endodontically treated teeth after clinical function.

Endodontically treated teeth restored with posts are susceptible to coronal leakage after long-term function. We hypothesize that demineralized collagen matrices (DCMs) created in dentin by acidic zinc phosphate cement within the dowel spaces degrade with time. Forty-two post-restored teeth were extracted after three periods of clinical service and were examined, by means of scanning and transmission electron microscopy, for the status of the DCMs. SEM revealed a progressive degradation of the DCMs, becoming less dense after 3 to 5 years, losing structural integrity after 6 to 9 years, and partially disappearing after 10 to 12 years. TEM revealed evidence of collagenolytic activity within the DCMs, with loss of cross-banding and unraveling into microfibrils, and gelatinolytic activity that resulted in disintegration of the microfibrils. Bacterial colonization and the release of bacterial enzymes and of host-derived matrix metalloproteinases may contribute to the degradation of collagen fibrils in root dentin after clinical function.

Bacteria↗

PubMed2004

In vivo and in vitro permeability of one-step self-etch adhesives.

Adhesive dentistry should effectively restore the peripheral seal of dentin after enamel removal. We hypothesize that non-rinsing, simplified, one-step self-etch adhesives are effective for minimizing dentin permeability after tooth preparation procedures. Crown preparations in vital human teeth were sealed with Adper Prompt, Xeno III, iBond, or One-Up Bond F. Epoxy resin replicas were produced from polyvinyl siloxane impressions for SEM examination. Dentin surfaces from extracted human teeth were bonded with these adhesives and connected to a fluid-transport model for permeability measurements and TEM examination. Dentinal fluid droplets were observed from adhesive surfaces in resin replicas of in vivo specimens. In vitro fluid conductance of dentin bonded with one-step self-etch adhesives was either similar to or greater than that of smear-layer-covered dentin. TEM revealed water trees within the adhesives that facilitate water movement across the polymerized, highly permeable adhesives. Both in vitro and in vivo results did not support the proposed hypothesis.

Acid Etching, Dental↗

PubMed2004

Water-dependent interfacial transition zone in resin-modified glass-ionomer cement/dentin interfaces.

The function of the interfacial transition zone (absorption layer) in resin-modified glass-ionomer cements bonded to deep dentin remains obscure. This study tested the hypotheses that the absorption layer is formed only in the presence of water derived from hydrated dentin and allows for better bonding of resin-modified glass-ionomer cements to dentin. Ten percent polyacrylic acid-conditioned, hydrated, and dehydrated deep dentin specimens were bonded with 2 resin-modified glass-ionomer cements and sealed with resins to prevent environmental water gain or loss. A non-particulate absorption layer was identified over hydrated dentin only, and was clearly discernible from the hybrid layer when bonded interfaces were examined with transmission electron microscopy. This layer was relatively more resistant to dehydration stresses, and remained intact over the dentin surface after tensile testing. The absorption layer mediates better bonding of resin-modified glass-ionomer cements to deep dentin, and functions as a stress-relieving layer to reduce stresses induced by desiccation and shrinkage.

Compomers↗

PubMed2004

Fluid movement across the resin-dentin interface during and after bonding.

This study evaluated the extent of water penetration through resin-dentin interfaces before and after being sealed with adhesives. Four adhesive resin systems (2 total-etch adhesives and 2 self-etching primer adhesives) were used in this study. Dentin disks were placed in a split-chamber device, and in situ fluid movement across dentin was measured, with and without physiological pressure, during bonding procedures or 24 hrs after bonding. The fluid movement across dentin occurs via dentin tubules after acid-etching. Large outward or inward fluid shifts across dentin were observed during air-drying and light-curing for resin application. The amount of fluid movement across resin-bonded dentin when total-etch adhesives were used was significantly greater than that with self-etching adhesives. The milder acid-etching effects of self-etching primers may retain hybridized smear plugs within the tubules that reduce outward fluid flow, resulting in superior dentin sealing.

Acid Etching, Dental↗

PubMed2003

Dimensional changes in acid-demineralized dentin matrices following the use of HEMA-water versus HEMA-alcohol primers.

Although dried acid-etched dentin can be reexpanded by hydroxyethyl methacrylate (HEMA)/water primers, the primed dentin collapses when the water is evaporated. Experimental HEMA/alcohol primers should stiffen the matrix and permit less shrinkage when the solvent is evaporated. The purpose of this study was to test the hypotheses that matrix shrinkage induced by solvent evaporation from HEMA primers is inversely related to solvent-induced matrix stiffness. Dentine discs were prepared from midcoronal dentine of unerupted human third molars. After demineralization in 37% phosphoric acid, the specimens were placed in the well of a linear variable differential transformer instrument, which measures changes in the matrix height and stiffness by load displacement after the application of weights. This was done in their hydrated state after water had been applied, after drying with dry nitrogen gas, and after the application of 35 vol % HEMA-water, HEMA-methanol, HEMA-ethanol, or HEMA-propanol primers. The degree of reexpansion after the application of the primers to the dentine in the dried state was found to be highest using the HEMA-water primer, followed by HEMA-methanol and HEMA-ethanol, with the HEMA-propanol primer producing no expansion. However, when the solvents were evaporated the HEMA-water-treated specimens shrank the most, the HEMA-ethanol-treated specimens shrank an intermediate amount, and the HEMA-methanol-treated specimens shrank the least. The net result of expansion minus shrinkage produced by evaporation determines how much HEMA remains in the hybrid layer just prior to polymerization.

Acids↗

PubMed2003

Optimizing filler content in an adhesive system containing pre-reacted glass-ionomer fillers.

OBJECTIVES: (1) To evaluate the optimal concentration of the calcium type pre-reacted glass-ionomer (PRG-Ca) fillers in experimental light-activated adhesives for bonding to tooth substrates and fluoride release; (2) to evaluate the polymerization reactivity of these experimental filled adhesives; and (3) to examine the ultrastructure of the resin-dentin interface bonded with the commercial version of this self-etching adhesive (Imperva Fluoro Bond, Shofu Inc., Kyoto, Japan). MATERIALS AND METHODS: PRG-Ca fillers were prepared from the acid-base reaction of calcium type fluoroaluminosilicate glass with poly(acrylic acid) in water. Different experimental light-cured adhesives were prepared, with 0-57wt% PRG-Ca fillers and 3wt% aerosil silica incorporated in a resin matrix. Twenty-four hours shear bond strengths to bovine enamel and dentin were assessed using the adhesive with/or without accelerated aging. The cumulative amount of fluoride released from the cured adhesives and differential scanning calorimetry (DSC) measurements were also conducted. 180-grit SiC paper polished human dentin disks were treated with Imperva Fluoro Bond that contains 17wt% PRG-Ca fillers and prepared for TEM examination. RESULTS: Increase in PRG-Ca filler content of experimental adhesives was highly correlated with the decrease in bond strengths to dentin (r=-0.96 to -0.99), the increase in cumulative fluoride release, (r=0.97) and the decrease in polymerization energy (cal/g) of the adhesives (r=-0.99) (p<0.001). A PRG-Ca content of 17wt% provided optimal bond strength to enamel and dentin after accelerated aging and fluoride release. TEM showed that salt-like matrices were present around the hydrogels and remnant glass cores of the PRG-Ca fillers. The commercial self-etching primer completely dissolved the smear layer and formed 2 micrometer thick hybrid layers in intact dentin. SIGNIFICANCE: The use of silanized PRG-Ca fillers provides good adhesion and a source of fluoride release in a commercially available self-etching adhesive system.

Analysis of Variance↗

PubMed2003

Aging affects two modes of nanoleakage expression in bonded dentin.

Water sorption into resin-dentin interfaces precedes hydrolytic degradation. We hypothesized that these processes are morphologically manifested by the uptake of ammoniacal silver nitrate, which is thought to trace hydrophilic domains and water-filled channels within matrices. Water sorption is thought to be nonuniform and can be traced by the use of silver nitrate. Human teeth bonded with an experimental filled-adhesive were aged in artificial saliva (experimental) or non-aqueous mineral oil (control). Specimens retrieved for up to a 12-month period were immersed in 50 wt% ammoniacal silver nitrate and examined by transmission electron microscopy for identification of the changes in their silver uptake. Reticular silver deposits initially identified within the bulk of hybrid layers in the experimental group were gradually reduced over time, but were subsequently replaced by similar deposits that were located along the hybrid layer-adhesive interface. Silver uptake in water-binding domains of the adhesive layers increased with aging, resulting in water tree formation. These water-filled channels may act as potential sites for hydrolytic degradation of resin-dentin bonds.

Absorption↗

PubMed2003

Effects of HEMA/solvent combinations on bond strength to dentin.

Re-expansion of dried demineralized dentin is required to optimize resin adhesion. This study tested the hypothesis that bond strengths to dentin depend upon the ability of experimental HEMA(2-hydroxy-ethyl-methacrylate)/solvent primers to re-expand the matrix. Dentin surfaces were acid-etched with 37% phosphoric acid for 20 sec, air-dried for 30 sec, primed with either 35/65% (v/v) HEMA/water, HEMA/methanol, HEMA/ethanol, or HEMA/propanol for 60 sec, and bonded with 4-META-TBBO(4-methacryloyloxyethyl trimellitate anhydride-tri-n-butyl borane) adhesive. After storage in water for 1 day at 37 degrees C, the samples were prepared for microtensile bond strength testing. We used transmission electron microscopy to measure the width of interfibrillar spaces in the hybrid layers. The HEMA/ethanol primer and the HEMA/propanol primer produced the highest and the lowest bond strengths, respectively (p < 0.05). Bond strengths were directly correlated with the width of the interfibrillar spaces (p < 0.05). Bond strengths are related to the ability of the primer to maintain the re-expansion of collapsed demineralized dentin matrix.

1-Propanol↗

PubMed2003

Integrating oxalate desensitizers with total-etch two-step adhesive.

Compromised bonding of total-etch adhesives to dentin treated with oxalate desensitizers results from the interference of a surface layer of acid-resistant crystals of calcium oxalate. We hypothesize that effective tubular occlusion and dentin bonding may be simultaneously achieved by depleting dentin surfaces of calcium with acids before desensitizer application. Dentin specimens treated with 4 oxalate desensitizers before or after being acid-etched were bonded with a two-step adhesive. Microtensile bond strengths ( micro TBS) were significantly lower, compared with the control, when oxalates were used before the specimens were acid-etched; in contrast, when oxalates were used after acid-etching. micro TBS were similar to nonoxalate-treated controls. Dentin surfaces and tubular orifices were covered with a surface layer of crystals when desensitizers were applied to fractured dentin and smear-layer-covered dentin before specimens were acid-etched. However, when the dentin was acid-etched prior to the application of oxalate desensitizers, the crystals were largely limited to the subsurface of dentinal tubules, where they did not interfere with subsequent resin bonding.

Acid Etching, Dental↗

PubMed2002

Micro-tensile bond strengths to sclerotic dentin using a self-etching and a total-etching technique.

OBJECTIVES: To evaluate the in vitro regional micro-tensile bond strengths of a self-etching/self-priming adhesive system to sclerotic dentin, in the absence or presence of phosphoric acid conditioning. METHODS: Naturally-occurring, non-carious cervical lesions on extracted premolars were hand-cleaned with a slurry of pumice and chlorhexidine, then bonded without further cavity preparation. One group was bonded using Clearfil Liner Bond 2V (Kuraray Co. Ltd., Osaka, Japan). The other group was first conditioned with K-etchant; 40% phosphoric acid gel (Kuraray) prior to the application of the self-etching primer. Artificially prepared wedge-shaped cavities were also made in sound premolars and bonded with the two methods as controls. Resin composite build-ups were made using Clearfil Protect Liner F and AP-X resin composite (Kuraray). After storage in water for 24h, the teeth were sectioned into 0.7 x 0.7 mm composite-dentin beams along the occlusal and gingival walls, and at the apex of the lesions. The use of two conditioning methods, two substrate types, and three different locations yielded 10-14 beams for each of the 12 groups. After testing for the microTBS, representative beams that were stressed to failure were examined with SEM. Remaining fractured beams were demineralized and processed for TEM examination. Statistical analysis was performed using a three-way ANOVA and Student-Newman-Keuls tests. RESULTS: Regardless of the conditioning methods, bond strengths to sound dentin were significantly higher than to sclerotic dentin (P< 0.05). With sclerotic dentin, there was no significant difference for the conditioning methods used, except that K-etchant significantly improved the bond strength at the gingival aspect of the lesions. Fractographic analysis revealed that the self-etching primer could not etch beyond the surface hypermineralized layer of sclerotic dentin. Interfacial failure occurred along the surface of the mineralized intermicrobial matrix and/or hypermineralized layer. With the use of phosphoric acid, a hybrid layer was only seen when the surface layers were thin. Incompletely removed sclerotic casts were evident in both groups. SIGNIFICANCE: Removal of the surface layers of sclerotic dentin and/or conditioning with stronger acids may be beneficial to obtain stronger bonding to sclerotic dentin.

Acid Etching, Dental↗

PubMed2002

Dimensional changes and ultimate tensile strengths of wet decalcified dentin applied with one-bottle adhesives.

OBJECTIVES: The objectives of this study were to test the null hypothesis that no dimensional changes in wet decalcified dentin matrices will occur during the application of one-bottle adhesives, and to evaluate the ultimate tensile strengths (UTS) of resin-infiltrated dentin matrices using the microtensile test. METHODS: Dentin disks 0.2 mm thick were prepared from mid-coronal dentin of human unerupted third molars. They were completely decalcified in 0.5 M EDTA (pH 7.4) for 5 days at 25 degrees C and then placed in the bottom of an aluminum well to permit use of the LVDT portion of a thermal mechanical analyzer. Changes in matrix height in response to the application of Single Bond, One-Step or Prime & Bond NT were measured along with the UTS of resin-infiltrated specimens that were compared using a one-way ANOVA and Fisher's PLSD test. RESULTS: All one-bottle adhesives produced a gradual, progressive shrinkage of the decalcified matrix of 26-33%. The shrinkage produced by Single Bond was significantly greater (p<0.05) than that produced by the other adhesives. The UTS of One-Step was significantly higher (<0.05) than that of Prime & Bond NT (42.0+/-13.6 vs 29.7+/-1.9 MPa, respectively), with Single Bond producing intermediate UTS (34.3+/-7.4 MPa). SIGNIFICANCE: If the durability of resin-dentin bonds depends upon the size of interfibrillar spaces for both diffusion channels and resin uptake, then adhesive formulations should be designed to minimize matrix shrinkage during resin infiltration.

Analysis of Variance↗

PubMed2002

Hygroscopic expansion of a compomer and a composite on artificial gap reduction.

OBJECTIVE: This study compared the effect of water sorption on the extent of marginal gap reduction in a compomer (Dyract AP, Dentsply) and a composite (Spectrum, Dentsply) over a 12-week storage period. MATERIALS AND METHODS: Artificial gaps were created in 40 borosilicate glass cylinders, each 5mm deep and with an internal diameter of 5.5mm. Half of the internal bonding surface of each cylinder was sandblasted, silanised and coated with a dentine adhesive (Prime&Bond NT, Dentsply). Twenty partially bonded cylinders were incrementally filled with Dyract AP (AP) and the rest with Spectrum (S). For each material, 10 specimens were stored in de-ionised water (W), and 10 (control) in non-aqueous silicone fluid (O) at 37 degrees C. The dimension of the same maximum gap created in each specimen was repeatedly measured at 0, 1, 2, 4, 6, 8, 10 and 12 weeks, using a light microscope under incident light at 570x magnification. Gap widths in each of the four groups (n=10) were statistically compared. Correlations between mean gap width reduction and storage time were also examined. RESULTS: Friedman repeated measures ANOVA on ranks revealed significant differences (p<0.001) among the gap widths measured at different time intervals in groups AP-W and S-W. No significant differences (p>0.05) were found in groups AP-O and S-O. Tukey's multiple comparison test indicated that no significant differences (p>0.05) were detectable beyond the sixth week in AP-W and the fourth week in S-W. Linear regression analyses showed that mean gap widths decreased exponentially with time for AP-W (r=0.97) and S-W (r=0.90). From the slopes of the regression lines, the rate of marginal gap reduction in AP-W was 4.6 times faster than S-W. CONCLUSION: Marginal gap reduction in both the materials are directly attributed to water sorption and that the reduction is larger and more rapid in Dyract AP.

Absorption↗

PubMed2002

A quantitative evaluation of apical leakage of four root-canal sealers.

AIM: This in vitro study evaluated the microleakage of root fillings involving four root-canal sealers including AH Plus (De-Trey, Switzerland), RoekoSeal (Roeko, Germany). Ketac-Endo (ESPE, (Germany) and Sultan (Sultan Chemists, USA. METHODOLOGY: Forty extracted human maxillary anterior teeth were used. The coronal part of each tooth was removed and the root canals were prepared using the step-back technique and apical enlargement to size 60 file. The specimens were randomly divided into four groups of 10 samples, filled with one of the test materials and gutta-percha cones by the cold lateral condensation technique. A fluid filtration method was used for quantitative evaluation of apical leakage. The leakage was measured by the movement of an air bubble in a capillary glass tube connected to the experimental root section. Measurements of fluid movement were made at 2-min intervals for 8 min. Water transport through existing voids in the obturated canals could be measured reproducibly in this way. The quality of the seal of each specimen was measured after 7,14 and 21 days. RESULTS: Statistical analysis indicated that all the root fillings showed less leakage after 21 days (P < 0.05). Fillings incorporating Sultan showed significantly more leakage than all other sealers. CONCLUSIONS: Root fillings with RoekoSeal in combination with cold lateral condensation technique showed better sealing than those with Ketac-Endo, AH Plus and Sultan sealers after 21 days. The fluid filtration test used in this study gave quantitative results and allowed nondestructive long-term evaluation of specimens.

Analysis of Variance↗

PubMed2002

Two modes of nanoleakage expression in single-step adhesives.

Self-etch adhesives that etch, prime, and bond simultaneously should not exhibit incomplete resin infiltration within hybrid layers. We hypothesized that nanoleakage patterns in these systems are artifacts caused by mineral dissolution in mildly acidic silver nitrate. Resin-dentin interfaces bonded with four single-step, self-etch adhesives were examined for nanoleakage by conventional (pH 4.2) and basic ammoniacal (pH 9.5) silver nitrate and prepared for transmission electron microscopy. All adhesives exhibited a reticular mode of nanoleakage within hybrid layers when conventional silver nitrate was used. With ammoniacal silver nitrate, an additional spotted pattern of nanoleakage was observed within adhesive and hybrid layers. The reticular mode of nanoleakage in self-etch adhesives probably represents sites of incomplete water removal that leads to regional suboptimal polymerization. The spotted pattern identified with the use of ammoniacal silver nitrate probably represents potentially permeable regions in the adhesive and hybrid layers that result from the interaction of the basic diamine silver ions with acidic/hydrophilic resin components.

Acid Etching, Dental↗

PubMed2002

Reversal of compromised bonding in bleached enamel.

Oxygen inhibits polymerization of resin-based materials. We hypothesized that compromised bonding to bleached enamel can be reversed with sodium ascorbate, an anti-oxidant. Sandblasted human enamel specimens were treated with distilled water (control) and 10% carbamide peroxide gel with or without further treatment with 10% sodium ascorbate. They were bonded with Single Bond (3M-ESPE) or Prime&Bond NT (Dentsply DeTrey) and restored with a composite. Specimens were prepared for microtensile bond testing and transmission electron microscopy after immersion in ammoniacal silver nitrate for nanoleakage evaluation. Bond strengths of both adhesives were reduced after bleaching but were reversed following sodium ascorbate treatment (P < 0.001). Resin-enamel interfaces in bleached enamel exhibited more extensive nanoleakage in the form of isolated silver grains and bubble-like silver deposits. Reduction of resin-enamel bond strength in bleached etched enamel is likely to be caused by a delayed release of oxygen that affects the polymerization of resin components.

Acid Etching, Dental↗