Biomedical subjects

Chengtao Wang

Publications and source records attributed to Chengtao Wang.

22 records · Page 2Linked to original sources

PubMed2003

[The effect of magnitopuncture stimulation on HRV during simulated driving under vibration conditions].

The purpose of this study was to assess the effect of magnitopuncture stimuli for reducing driver mental stress and fatigue using power spectral analysis of the heart rate variability (HRV) and subjective evaluation. The experiments were divided into A-group and B-group. In both groups the subjects performed the simulator for 90 minutes under a vibration conditions with an erect sitting posture in a silent environment, and magnitopuncture was put on the acupoints when performing the task for one hour in A-group. In this study HRV exhibited a significant difference between the two groups after the simulating task (P < 0.05). A conclusion that magnitopuncture stimuli can reduce the driver mental stress and fatigue effectively was drawn.

Acupuncture Points↗

PubMed2002

Effect of magnitopuncture on sympathetic and parasympathetic nerve activities in healthy drivers--assessment by power spectrum analysis of heart rate variability.

The object of this study was to assess the effects of magnitopuncture applied to Dazhui (DU14) point and Neiguan (PC6) points on sympathetic and parasympathetic nerve activities by power spectrum analysis of heart rate variability in healthy drivers during simulated driving. Using power spectrum analysis, the low frequency (LF) and high frequency (HF) components of heart rate variability can be calculated reflecting the sympathetic and parasympathetic activity. The 40 healthy male subjects were randomly divided into two groups: A (study group) and B (control group). All subjects were required to be well rested before the experiment. The subjects of both groups were required to perform a simulated driving task for 3 h. During the driving, magnitopunctures were applied to the DU14 and PC6 points for A while the subject performed the task for 2.5 h, and for B magnitopunctures were applied to non-acupuncture points which were 1.5 cm away from the two acupuncture points respectively over the same time. Subjective response to a questionnaire was obtained after the simulated task in the two groups. At the end of the driving task the LF component in normalized units (NU) had decreased significantly ( P<0.05) indicating a reduced sympathetic nerve activity and the HF component (NU) increased significantly ( P<0.05) indicating a increased parasympathetic nerve activity for A compared with pre-stimulation while for B no significant differences were observed. There were significant group differences in LF (NU), HF (NU) and LF:HF at the end of the driving task ( P<0.05). It was concluded that a modulating effect of magnitopuncture on sympathetic and parasympathetic nerve activities in healthy subjects was associated with the acupuncture points. The findings represent physiological evidence that magnitopuncture may reduce mental fatigue in healthy drivers.

Acupuncture↗

PubMed2002

[Multiagent system for individual artificial hip joint].

Based on the introduction of multi-agent and individual artificial hip joints, this paper reports a multi-agent design system for individual artificial hip joints. Three agents are defined, the first is to optimize the diameter of hip joint, the second for FEM, the third for simulation between the prosthesis and acetabulum cup. The paper lays emphasis on the second agent.

Acetabulum↗

PubMedDate not supplied

Design and fabrication of auricular prostheses by CAD/CAM system.

PURPOSE: The purpose of this report is to describe a new technique for fabricating auricular prostheses by a computer-aided design/manufacturing (CAD/CAM) system. MATERIALS AND METHODS: A spiral CT was performed on a patient who had a right ear defect resulting from an accident. A 3-D image was reconstructed with the CT data. Through image ware, the image of the normal ear was extracted, mirrored, and Boolean operated with the image of the deformed side of the face. It was well modified and smoothed in the FreeForm model system so that it could precisely adapt to the deficient side of the face. A paper model ear was manufactured by rapid prototyping from the digitized data. Finally, silicone was poured into a silicone mold from the paper ear to create a silicone auricular prosthesis. RESULTS: The dimension, shape, and anatomic contour of the auricular prosthesis were quite similar to those of the normal ear and precisely matched the deformed area. CONCLUSION: The CAD/CAM system for creating auricular prostheses appears to be a practical technique.

Adult↗