Search PubMed⌕ Search

Biomedical subjects

C H Gibbs

Publications and source records attributed to C H Gibbs.

At least 19 recordsLinked to original sources
PubMed1999

An algometer for intraoral pain tolerance measurements.

An algometer was developed to provide a variable probing force (0-200 g force) which could be used intraorally. This algometer consisted of an autoclavable probe handpiece attached to an optical encoder, which recorded probing force to a computer when a button was pressed. The probe handpiece included a 0.40 mm diameter hemispherical tip which was placed in contact with the experimental site. The probe tip was pressed against the tissue with increasing force until the subject pressed the button, at which point the pain tolerance (PT) value was recorded by the computer. Intraoral soft tissue, PT values were obtained from nine healthy adult subjects during 6 weekly visits to determine the reproducibility of PT measurements. Five gingival sulcus sites and three gingival surface sites, all adjacent to the maxillary premolars constituted the experimental area. The reproducibility of PT values using the force stimulus from the algometer was evaluated using interclass correlation coefficients (R) for each of the eight sites. Visits 1 and 2 were training and calibration visits. Visits 3 through 6 were experimental visits. The R values ranged from 0.40 to 0.79 when data from all six visits were included. R values for Visits 3 through 6 were 0.63-0.97 indicating good to excellent correlation after subjects became familiar with the procedure. A complete repeated measures analysis of variance (ANOVA) showed no significant interaction between site and visit. Duncan's multiple range test was used to compare sensitivity across the eight sites. The results indicated that the three most anterior sites were significantly (P < 0.05) more sensitive than four of the posterior sites. When the sites were grouped into: (1) gingival surface sites; (2) mid-facial sulcus sites; and (3) interproximal sulcus sites, no significant differences were found in their PT values. The algometer is well suited for intraoral investigations because of its precision, computerized data entry and easily positioned, autoclavable handpiece. This new algometer may be useful for sensory and pain studies for other parts of the body.

Adult↗
PubMed1998

Pain threshold values during periodontal probing: assessment of maxillary incisor and molar sites.

Probing pain threshold (PPT) assessments were conducted in the facial and oral sulci of maxillary central incisors and first molars of 10 periodontally healthy adults. All subjects were systemically healthy, free of pain, and reported no current medication usage. A computer-linked electronic probe, modified to deliver steadily increasing forces up to 200 grams, was used to collect the data. The system contained a subject operated "off-switch" which, upon activation, signaled the computer to record the subject's PPT. Assessments of each subject's PPTs were conducted on 3 separate occasions at 7-day intervals. Results indicated that the facial sulci of the incisors were the most pain sensitive. They displayed a mean PPT of 50.9 +/- 26.6 grams. The oral sulci of the incisors exhibited a mean PPT of 76.5 +/- 45.2 grams. Facial and oral sulci of the molars evidenced mean PPT values of 102.6 +/- 52.1 grams and 113.5 +/- 51.3 grams, respectively. These data suggest that sulci associated with incisor teeth are nearly twice as pain sensitive as sulci associated with molar teeth. In addition, facial sulci are significantly more pain sensitive than oral sulci. Data did not indicate a visit effect nor a side-of-mouth effect on PPT values.

Adult↗
PubMed1996

The nonsurgical treatment of a Class II open bite malocclusion.

This case was treated by residents in the postgraduate orthodontic program at the University of Florida under the supervision of Dr. Hocevar. A treatment regimen that he developed to increase the strength and endurance of the masticatory muscles was used. The patient performed prescribed daily clenching and chewing exercise with resilient posterior bite-blocks and wore a hard acrylic posterior biteplane the remainder of the time. It was hoped that this approach would increase the chances of treatment success and stability.

Adolescent↗
PubMed1996

Light source-induced error in computer-assisted image analysis with a video-based system.

OBJECTIVE: We tested the hypothesis that two different light sources, an alternating current fluorescent viewbox and a direct current halogen viewbox, do not differ with respect to their ability to illuminate reproducibly a radiograph during image capture. STUDY DESIGN: Two radiographs were taken: one with four hydroxyapatite chips mounted against a dry mandible and one without the chips. They were digitally subtracted with a video-based imaging system. The procedure was repeated at different times. RESULTS: A statistically significant difference among optical density measurements was found when the alternating current fluorescent viewbox (p < 0.001) was used and was related to light intensity variation. Such effect was not observed with the direct current halogen viewbox (p = 0.873). CONCLUSION: Study design efficiency was increased by 212% with the use of the direct current halogen viewbox so that to detect a specified treatment effect with a given level of statistical confidence, the sample size has to be 2.12 times greater if the alternating current fluorescent viewbox is used.

Absorptiometry, Photon↗
PubMed1991

Analysis of repeated-measure multicycle unilateral mastication in children.

This study examined systematic and random errors associated with repeated-measure, multiple-cycle unilateral mastication in children during single recording sessions with the Replicator system. Twenty-six recording sessions with 17 children (10 boys, 7 girls) were examined. Nine of these children had a functional-shift unilateral crossbite malocclusion and were recorded before and after crossbite correction. Repeated recordings (trials) of mandibular movement during each session were made of right-side chewing of similar-sized pieces of cheese. The following variables were computed for each chewing cycle (stroke): time closed, maximum closure velocity, maximum opening velocity, chewing rate, vertical opening, and lateral deviation. From the multiple cycles of each trial, two pattern descriptors--the average and standard deviation--were determined for each variable. In addition, the mean and variance of these pattern descriptors were determined from the multiple trials of each recording session and were the dependent variables in a stepwise multiple regression analysis, with treatment status, sex, age, dentition stage, crossbite presence, and right side status the independent variables. The results disclosed bias in repeated measures of human chewing in response to adaptation to the recording session; this was evident in the average response but not in the variability of the measures. Sex and functional status of the subjects were associated with the mean and variance of measures describing the chewing pattern.

Adolescent↗
PubMed1990

Biting strength and chewing forces in complete denture wearers.

Most studies concur that denture wearers have only about one fifth to one fourth the bite strength and masticatory force of natural dentition subjects. There appears to be a wide range of acceptable chewing forces, as evidenced by the wide variation in bite strength of natural dentition subjects. However, bite strength and masticatory forces in denture wearers fall below the natural dentition range and therefore it is concluded that denture wearers are handicapped in bite force. The occlusal form of the posterior denture teeth did not significantly influence masticatory force.

Analysis of Variance↗
PubMed1990

Temporomandibular joint forces measured at the condyle of Macaca arctoides.

Forces were measured at the articular surface of the temporomandibular joint (TMJ) condyle in two stump-tail monkeys (Macaca arctoides) during chewing, incisal biting, and drinking and also during aggressive behaviors. Force was measured with a thin piezoelectric foil transducer, which was cemented over the anterior and superior surfaces of the condyle. Wires from the upper and lower surfaces of the foil were insulated between two layers of Teflon tape and run subcutaneously to a telemetry unit, which was implanted in the upper back. Force applied across the foil by the condyle was detected by the telemetry unit and transmitted to an FM radio receiver outside the animal. The FM signals were received and demodulated, and a signal proportional to the force applied between the condyle and the TMJ fossa was displayed on a chart recorder. Data were collected over an 8-day period. The animals were not constrained. The TMJ was found to be load bearing. The greatest force of 39.0 lb (17.7 kg) was measured during feisty vocal aggression. Forces ranged as high as 34.5 lb (15.7 kg) during chewing and 28.5 lb (13.0 kg) during incisal biting. Forces were greater on the working (food) side than on the nonworking (balancing) side by average ratios of 1.4 to 2.6. A large unilateral interference at the most distal molar greatly disturbed chewing. It reduced TMJ forces by 50% or more, and the monkey refused to chew on the side opposite the interference.

Aggression↗
PubMed1989

A preliminary study of the effects of tooth guidance on working-side condylar movement.

Clinical observations have indicated that lateral working-side tooth contacts can produce a posterior shift of the working-side condyle, resulting in pain in the temporomandibular joint. This study examined the influence of lateral retrusive and lateral protrusive tooth guidance on the movements of working condyles of the lateral pole. Four patients with lateral retrusive natural tooth contacts and four patients with lateral protrusive natural tooth contacts were studied. Movement of the lateral pole of the working condyle was recorded under the following conditions: (1) natural teeth in contact, (2) wearing of a mandibular acrylic resin splint that created lateral protrusive or lateral retrusive tooth guidance, and (3) a central bearing screw and bearing plate separating the teeth. The results indicated that the condition of the patient's temporomandibular joints was a crucial factor in consistency of condylar tracings. Condylar tracings from patients with temporomandibular joint condyle-disk lacking coordination were inconsistent and unreproducible. Consistent, reproducible tracings for patients without condyle-disk disorders indicated that lateral retrusive guidance can cause a more posterior pathway of the lateral pole of the working condyle than lateral protrusive guidance. Future studies are necessary to establish the relationship between lateral tooth guidance and temporomandibular disorders.

Adult↗
PubMed1988

Description and clinical evaluation of a new computerized periodontal probe--the Florida probe.

A new periodontal probing system has been developed which incorporates the advantages of constant probing force, precise electronic measurement to 0.1 mm and computer storage of the data. The system includes a probe handpiece, displacement transducer with digital readout, foot switch, computer interface and personal computer. A unique movable arm design enables the probe handpiece to maintain smooth operation and makes it easy to clean and sterilize. Electronic recording of the data (actuated by pressing a foot switch) eliminates errors which occur when probe tip markings are read visually and the data are called to an assistant. Computer storage and analysis of the data facilitates detecting changes in pocket depth and attachment level by rapidly comparing data recorded at different visits. The system was evaluated in 3 experiments using a 0.4 mm diameter tip and a 25 g probing force. The standard deviation of repeated pocket depth measurement was less (0.58 mm versus 0.82 mm) than that of a common probe. With paired readings referenced to an occlusal stent, the standard deviation of repeated attachment level measurements was 0.28 mm. A loss of attachment level was detected to a certainty of 99% with less than a 1 mm change. This is a significant improvement over common probes, which require a 2-3 mm change for equivalent positive identification of change in attachment level.

Computers↗
PubMed1988

Correlation between electronic and visual readings of pocket depths with a newly developed constant force probe.

The purpose of this study was to compare probing measurements obtained using a newly developed constant force electronic probe, which eliminates errors of visual reading and variable force, to those obtained using a standard periodontal probe. The probe was connected to a digital readout through a linear variable differential transformer; the digital readout was connected to a printer and a foot switch. When the probe was in position and the foot switch depressed, the pocket depth was printed to the nearest 0.1 mm. 12 subjects with minimal to early periodontitis were selected for the study. The pocket depths of each patient were recorded electronically utilizing a constant force of 25 g, and conventionally using the same instrument in a "locked" position and visual reading. Probings were performed on each subject by 3 different examiners, on 3 separate occasions 2-3 days apart. The results showed a high correlation between manual and electronic probing. The average correlations for the 3 investigators between examinations were consistently higher for the electronic probings. In comparing the 3 examiners to each other, consistently higher correlations were found for the electronic pocket readings. Correlations for single-rooted teeth were lower for all 3 examiners. The pocket depth measurements recorded when using the manual probe with visual readings were consistently deeper than those obtained using the electronic probe with computer readings. It was concluded that the reproducibility of measurements obtained with the electronic probe was significantly superior to that obtained with a manual probe.

Adult↗
PubMed1988

Attachment level measurements with a constant force electronic probe.

The purpose of the present investigation was to evaluate the reproducibility of probing attachment level measurements using a newly developed constant force electronic probe. The probing force was preset at 25 g (probe diameter 0.4 mm) and was connected to a computer through a variable differential transformer. The measurements were performed on 10 patients with minimal signs of periodontal disease, using individually made acrylic stents. When the probe was in place and a foot switch depressed, the measurement was stored on the computer to the nearest 0.1 mm. The measurements were performed by one periodontist and one hygienist during one visit, and were then repeated by the same periodontist and another hygienist during a second visit. The results showed high correlations between the periodontist and the hygienist during one visit, between the two visits for the periodontist, and between the two hygienists at two different visits. The subject threshold for attachment loss was calculated according to Haffajee and co-workers, and was found to average 0.84 mm for the measurements performed by the periodontist and the hygienist during the same visit. For the periodontist during two separate visits and for the two different hygienists, the average threshold was 0.99 and 1.02 mm, respectively. Duplicate measurements were also performed by one periodontist at one visit on 10 patients with advanced periodontal disease. The average subject threshold for these patients was 0.60 mm. It may be concluded that with the constant force electronic probe, loss of attachment can be detected earlier than when conventional instruments are used.

Dental Hygienists↗